DC-to-DC converter

DC-to-DC converter
An assortment of 78xx series ICs, linear DC-DC converters

A DC-to-DC converter is an electronic circuit which converts a source of direct current (DC) from one voltage level to another. It is a class of power converter.

Contents

Usage

DC to DC converters are important in portable electronic devices such as cellular phones and laptop computers, which are supplied with power from batteries primarily. Such electronic devices often contain several sub-circuits, each with its own voltage level requirement different from that supplied by the battery or an external supply (sometimes higher or lower than the supply voltage). Additionally, the battery voltage declines as its stored power is drained. Switched DC to DC converters offer a method to increase voltage from a partially lowered battery voltage thereby saving space instead of using multiple batteries to accomplish the same thing.

Most DC to DC converters also regulate the output. Some exceptions include high-efficiency LED power sources, which are a kind of DC to DC converter that regulates the current through the LEDs, and simple charge pumps which double or triple the input voltage.

Conversion methods

Electronic

Linear

Linear regulators can only output at lower voltages from the input. They are very inefficient when the voltage drop is large and the current is high as they dissipate heat equal to the product of the output current and the voltage drop; consequently they are not normally used for large-drop high-current applications.

The inefficiency wastes power and requires higher-rated, and consequently more expensive and larger, components. The heat dissipated by high-power supplies is a problem in itself as it must be removed from the circuitry to prevent unacceptable temperature rises.

They are practical if the current is low, the power dissipated being small, although it may still be a large fraction of the total power consumed. They are often used as part of a simple regulated power supply for higher currents: a transformer generates a voltage which, when rectified, is a little higher than that needed to bias the linear regulator. The linear regulator drops the excess voltage, reducing hum-generating ripple current and providing a constant output voltage independent of normal fluctuations of the unregulated input voltage from the transformer / bridge rectifier circuit and of the load current.

Linear regulators are inexpensive, reliable if good heat sinking is used and much simpler than switching regulators. As part of a power supply they may require a transformer, which is larger for a given power level than that required by a switch-mode power supply. Linear regulators can provide a very low-noise output voltage, and are very suitable for powering noise-sensitive low-power analog and radio frequency circuits. A popular design approach is to use an LDO, Low Drop-out Regulator, that provides a local "point of load" DC supply to a low power circuit.

Switched-mode conversion

Electronic switch-mode DC to DC converters convert one DC voltage level to another, by storing the input energy temporarily and then releasing that energy to the output at a different voltage. The storage may be in either magnetic field storage components (inductors, transformers) or electric field storage components (capacitors). This conversion method is more power efficient (often 75% to 98%) than linear voltage regulation (which dissipates unwanted power as heat). This efficiency is beneficial to increasing the running time of battery operated devices. The efficiency has increased since the late 1980s due to the use of power FETs, which are able to switch at high frequency more efficiently than power bipolar transistors, which incur more switching losses and require a more complicated drive circuit. Another important innovation in DC-DC converters is the use of synchronous rectification replacing the flywheel diode with a power FET with low "On" resistance, thereby reducing switching losses.

Most DC to DC converters are designed to move power in only one direction, from the input to the output. However, all switching regulator topologies can be made bi-directional by replacing all diodes with independently controlled active rectification. A bi-directional converter can move power in either direction, which is useful in applications requiring regenerative braking.

Drawbacks of switching converters include complexity, electronic noise (EMI / RFI) and to some extent cost, although this has come down with advances in chip design.

DC to DC converters are now available as integrated circuits needing minimal additional components. DC to DC converters are also available as a complete hybrid circuit component, ready for use within an electronic assembly.

Magnetic

In these DC to DC converters, energy is periodically stored into and released from a magnetic field in an inductor or a transformer, typically in the range from 300 kHz to 10 MHz. By adjusting the duty cycle of the charging voltage (that is, the ratio of on/off time), the amount of power transferred can be controlled. Usually, this is applied to control the output voltage, though it could be applied to control the input current, the output current, or maintain a constant power. Transformer-based converters may provide isolation between the input and the output. In general, the term "DC to DC converter" refers to one of these switching converters. These circuits are the heart of a switched-mode power supply. Many topologies exist. This table shows the most common.

Forward
  • Energy goes from the input, through the magnetics and to the load, simultaneously
Flyback
  • Energy goes from the input and stored in the magnetics
  • Later, it is released from the magnetics to the load
No transformer
  • Non-isolated
Step-down (Buck) - The output voltage is lower than the input voltage, and of the same polarity
  • Non-inverting: The output voltage is the same polarity as the input
    • Step-up (Boost) - The output voltage is higher than the input voltage
    • SEPIC - The output voltage can be lower or higher than the input
  • Inverting: the output voltage is of the opposite polarity as the input
True Buck-Boost - The output voltage is the same polarity as the input and can be lower or higher
Split-Pi (Boost-Buck) - Allows bidirectional voltage conversion with the output voltage the same polarity as the input and can be lower or higher
With transformer
  • May be isolated
Flyback - 1 or 2 transistor drive

In addition, each topology may be:

  • Hard switched - transistors switch quickly while exposed to both full voltage and full current
  • Resonant - an LC circuit shapes the voltage across the transistor and current through it so that the transistor switches when either the voltage or the current is zero

Magnetic DC to DC converters may be operated in two modes, according to the current in its main magnetic component (inductor or transformer):

  • Continuous - the current fluctuates but never goes down to zero
  • Discontinuous - the current fluctuates during the cycle, going down to zero at or before the end of each cycle

A converter may be designed to operate in Continuous mode at high power, and in Discontinuous mode at low power.

The Half bridge and Flyback topologies are similar in that energy stored in the magnetic core needs to be dissipated so that the core does not saturate. Power transmission in a flyback circuit is limited by the amount of energy that can be stored in the core, while forward circuits are usually limited by the I/V characteristics of the switches.

Although MOSFET switches can tolerate simultaneous full current and voltage (although thermal stress and electromigration can shorten the MTBF), bipolar switches generally can't so require the use of a snubber (or two).

Capacitive

Switched capacitor converters rely on alternately connecting capacitors to the input and output in differing topologies. For example, a switched-capacitor reducing converter might charge two capacitors in series and then discharge them in parallel. This would produce an output voltage of half the input voltage, but at twice the current (minus various inefficiencies). Because they operate on discrete quantities of charge, these are also sometimes referred to as charge pump converters. They are typically used in applications requiring relatively small amounts of current, as at higher current loads the increased efficiency and smaller size of switch-mode converters makes them a better choice.[citation needed] They are also used at extremely high voltages, as magnetics would break down at such voltages.

Electrochemical

A further means of DC to DC conversion in the kiloWatt to many MegaWatts range is presented by using redox flow batteries such as the vanadium redox battery, although this technique has not been applied commercially to date.

Terminology

Step-down - A converter where output voltage is lower than the input voltage. Like a Buck converter.

Step-up - A converter that outputs a voltage higher than the input voltage. Like a Boost converter.

Continuous Current Mode - Current and thus the magnetic field in the inductive energy storage never reach zero.

Discontinuous Current Mode - Current and thus the magnetic field in the inductive energy storage may reach or cross zero.

Noise - Since all properly designed DC to DC converters are completely inaudible, "noise" in discussing them always refers to unwanted electrical and electromagnetic signal noise.

Output noise - The output of a DC to DC converter is designed to have a flat, constant output voltage. Unfortunately, all real DC to DC converters produce an output that constantly varies up and down from the nominal designed output voltage. This varying voltage on the output is the output noise. All DC to DC converters, including linear regulators, have some thermal output noise. Switching converters have, in addition, switching noise at the switching frequency and its harmonics. Some sensitive radio frequency and analog circuits require a power supply with so little noise that it can only be provided by a linear regulator. Many analog circuits require a power supply with relatively low noise, but can tolerate some of the less-noisy switching converters.[1]

Input noise - If the converter loads the input with sharp load edges. Electrical noise can be emitted from the supplying power lines as RF noise. Which should be prevented with proper filtering in the input stage of the converter.

RF noise - Switching converters inherently emit radio waves at the switching frequency and its harmonics. Switching converters that produce triangular switching current, such as the Split-Pi or Ćuk converter in continuous current mode, produce less harmonic noise than other switching converters.[1] Linear converters produce practically no RF noise. Too much RF noise causes electromagnetic interference (EMI).

See also

References

  1. ^ a b "Making -5V 14-bit Quiet" by Kevin Hoskins 1997


External links


Wikimedia Foundation. 2010.

Игры ⚽ Поможем решить контрольную работу

Look at other dictionaries:

  • Converter — may refer to: Contents 1 Electromagnetics 2 Electronics 2.1 In television 3 Information technology …   Wikipedia

  • Converter — Жанр power noise rhythmic noise Страна …   Википедия

  • converter — em converteu o dinheiro em acções. converter a converteu o ao cristianismo …   Dicionario dos verbos portugueses

  • converter — [kən vʉr′tər] n. a person or thing that converts; specif., a) a furnace for converting pig iron into steel in the Bessemer process b) an electrical device for converting alternating current into direct current: cf. INVERTER c) the part of a radio …   English World dictionary

  • Converter — Con*vert er, n. 1. One who converts; one who makes converts. [1913 Webster] 2. (Steel Manuf.) A retort, used in the Bessemer process, in which molten cast iron is decarburized and converted into steel by a blast of air forced through the liquid… …   The Collaborative International Dictionary of English

  • Converter — Converter. См. Конвертер. (Источник: «Металлы и сплавы. Справочник.» Под редакцией Ю.П. Солнцева; НПО Профессионал , НПО Мир и семья ; Санкт Петербург, 2003 г.) …   Словарь металлургических терминов

  • Converter — См. Реактор конвертер Термины атомной энергетики. Концерн Росэнергоатом, 2010 …   Термины атомной энергетики

  • converter reactor — n. a nuclear reactor that produces less fissionable material than it consumes, or one that produces a different fissionable material than it consumes * * * …   Universalium

  • converter — (n.) 1530s, agent noun from CONVERT (Cf. convert) (v.). Of machinery, from 1867 …   Etymology dictionary

  • converter — |ê| v. tr. 1. Operar a conversão de. 2. Mudar, transformar. 3. Substituir. 4. Mudar (moralmente) para melhor. 5. Abraçar (uma religião) …   Dicionário da Língua Portuguesa

  • converter reactor — n. a nuclear reactor that produces less fissionable material than it consumes, or one that produces a different fissionable material than it consumes …   English World dictionary

Share the article and excerpts

Direct link
Do a right-click on the link above
and select “Copy Link”