Surface micromachining

Surface micromachining

Surface micromachining is a process used to produce micromachinery or MEMS.

Unlike Bulk micromachining, where a silicon substrate (wafer) is selectively etched to produce structures, surface micromachining is based on the deposition and etching of different structural layers on top of the substrate. [cite journal |last=Bustillo |first=J.M. |coauthors=R.T. Howe and R.S. Muller |year=1998 |month=August |title=Surface micromachining for microelectromechanical systems |journal=Proceedings of the IEEE |volume=86 |issue=8 |pages=1552–1574 |doi=10.1109/5.704260]

As the structures are built on top of the substrate and not inside it, the substrate's properties are not as important as in bulk micromachining, and the expensive silicon wafers can be replaced by cheaper substrates, such as glass or plastic. The size of the substrates can also be much larger than a silicon wafer, and surface micromachining is used to produce TFTs on large area glass substrates for flat panel displays. This technology can also be used for the manufacture of thin film solar cells, which can be deposited on glass, but also on PET substrates or other non-rigid materials.

Fabrication Process

Surface micromachining starts with a silicon wafer or other substrate and grows layers on top. These layers are selectively etched by photolithography and either a wet etch involving an acid or a dry etch involving an ionized gas, or plasma. Dry etching can combine chemical etching with physical etching, or ion bombardment of the material. Surface micromachining can involve as many layers as is needed with a different mask (producing a different pattern) on each layer. Modern integrated circuit fabrication uses this technique and can use dozens of layers, approaching 100. Micromachining is a younger technology and usually uses no more than 5 or 6 layers. Surface micromachining uses developed technology (although sometimes not enough for demanding applications)which is very repeatable for volume production.

acrificial Layers

Complicated components, such as movable parts, are built using a "sacrificial layer". For example, a suspended cantilever can be built by depositing and structuring a sacrificial layer, which is then selectively removed at the locations where the future beams must be attached to the substrate (i.e. the anchor points). The "structural layer" is then deposited on top of the polymer and structured to define the beams. Finally, the sacrificial layer is removed to release the beams, using a selective etch process that will not damage the structural layer.

There are many possible combinations of structural/sacrificial layer. The combination chosen depends on the process. For example it is important for the structural layer not to be damaged by the process used to remove the sacrificial layer.

References


Wikimedia Foundation. 2010.

Игры ⚽ Поможем решить контрольную работу

Look at other dictionaries:

  • Micromachining — may refer to: Superfinishing, a metalworking process for producing very fine surface finishes Various microelectromechanical systems Bulk micromachining Surface micromachining High aspect ratio microstructure technologies See also High aspect… …   Wikipedia

  • Bulk micromachining — is a process used to produce micromachinery or microelectromechanical systems (MEMS).Unlike surface micromachining, which uses a succession of thin film deposition and selective etching, bulk micromachining defines structures by selectively… …   Wikipedia

  • Microelectromechanical systems — (MEMS) (also written as micro electro mechanical, MicroElectroMechanical or microelectronic and microelectromechanical systems) is the technology of very small mechanical devices driven by electricity; it merges at the nano scale into… …   Wikipedia

  • Microfluidics — deals with the behavior, precise control and manipulation of fluids that are geometrically constrained to a small, typically sub millimeter, scale. Typically, micro means one of the following features: small volumes (nl, pl, fl) small size low… …   Wikipedia

  • Microtechnology — is technology with features near one micrometre (one millionth of a metre, or 10−6 metre, or 1μm). In the 1960s, scientists learned that by arraying large numbers of microscopic transistors on a single chip, microelectronic circuits could be… …   Wikipedia

  • Micromachinery — micromachines redirects here. For the toys, see Micro Machines. For the video games based on the toys, see Micro Machines (video games). A micromachine by Sandia is moved by a lit LED at Miraikan in Tokyo …   Wikipedia

  • 3D microfabrication — relates to the engineering of bulk solids on the micrometre or submicrometre scale. Although the term nanofabrication might be considered for the submicrometre scale, it is not in common use, and tends to relate to a bottom up approach (while… …   Wikipedia

  • Nanofluidic circuitry — is a nanotechnology aiming for control of fluids in nanometer scale. Due to the effect of an electrical double layer within the fluid channel, the behavior of nanofluid is observed to be significantly different compared with its microfluidic… …   Wikipedia

  • Millipede memory — Computer memory types Volatile RAM DRAM (e.g., DDR SDRAM) SRAM In development T RAM Z RAM TTRAM Historical Delay line memory Selectron tube Williams tube Non volatile …   Wikipedia

  • Comb drive — Comb drives capacitive actuators, often used linear actuators that utilize electrostatic forces that act between two electrically conductive combs. Comb drive actuators typically operate at the micro or nanometer scale and are generally… …   Wikipedia

Share the article and excerpts

Direct link
Do a right-click on the link above
and select “Copy Link”