Comparison of synchronous and asynchronous signalling

Comparison of synchronous and asynchronous signalling

Synchronous and asynchronous transmissions are two different methods of transmission synchronization. Synchronous transmissions are synchronized by an external clock, while asynchronous transmissions are synchronized by special signals along the transmission medium.

Contents

The need for synchronization

Whenever an electronic device transmits digital (and sometimes analogue) data to another electronic device, there must be a certain rhythm established between the two devices, i.e., the receiving device must have some way of knowing, within the context of the fluctuating signal that it's receiving, where each unit of data begins and where it ends.

For example, a television transmitter produces a continuous stream of data in which each horizontal line of image must be distinguishable from the preceding and succeeding lines, so that a TV will be able to distinguish between them upon reception.

Or, a serial data signal between two PCs must have individual bits and bytes that the receiving PC can distinguish. If it doesn't, then the receiving PC can't tell where one byte or bit ends and the next one begins.

So the signal must be synchronized in a way that the receiver can distinguish the bits and bytes as the transmitter intends them to be distinguished.

Methods of synchronization

There are two ways to synchronize the two ends of the communication.

The synchronous signalling methods use 2 different signals. A pulse on one signal indicates when another bit of information is ready on the other signal.

The asynchronous signalling methods use only 1 signal. The receiver uses transitions on that signal to figure out the transmitter bit rate ("autobaud") and timing, and set a local clock to the proper timing, typically using a phase-locked loop (PLL) to synchronize with the transmission rate. A pulse from the local clock indicates when another bit is ready.

Data/strobe synchronous transmission

In synchronous transmission, the stream of data to be transferred is encoded as fluctuating voltages on one wire, and a periodic pulse of voltage is put on another wire (often called the "clock" or "strobe") that tells the receiver "here's where one bit/byte ends and the next one begins".

Practically all parallel communications protocols use such synchronous transmission. For example, in a computer, address information is transmitted synchronously—the address bits over the address bus, and the read strobe in the control bus.

Single-wire synchronous signalling

Synchronization can also be embedded into a signal on a single wire. In differential Manchester encoding, used on broadcast quality video tape systems[citation needed], each transition from a low to high or high to low represents a logical zero. A logical one is indicated when there are two transitions in the same time frame as a zero. Another example is the Manchester code where a transition from low to high indicates a one and a transition from high to low indicates a zero. When there are successive ones or zeros, an opposite transition is required on the edge of the time frame to prepare for the next transition.

Asynchronous transmission

In one form of asynchronous transmission, there is only one wire/signal carrying the transmission. The transmitter sends a stream of data and periodically inserts a certain signal element into the stream which can be "seen" and distinguished by the receiver as a sync signal.

That sync signal might be a single pulse (a "start bit" in asynchronous start/stop communication), or it may be a more complicated syncword or self-synchronizing code such as HDLC or 8B/10B encoding.

Other forms of asynchronous communication use two wires for each data bit (dual-rail encoding) or one wire for each data bit and a separate timing wire (bundled data). Both of these require a separate acknowledge wire.

Obviously, the term "asynchronous" is misleading in its literal interpretation considering that the resynchronization problem can be easily rectified...

Advantages and disadvantages

Advantages Disadvantages
Asynchronous transmission
  • Simple, doesn't require synchronization of both communication sides
  • Cheap, timing is not as critical as for synchronous transmission, therefore hardware can be made cheaper
  • Set-up is very fast, so well suited for applications where messages are generated at irregular intervals, for example data entry from the keyboard
  • Large relative overhead, a high proportion of the transmitted bits are uniquely for control purposes and thus carry no useful information
Synchronous transmission
  • Lower overhead and thus, greater throughput
  • Slightly more complex
  • Hardware is more expensive

Wikimedia Foundation. 2010.

Игры ⚽ Нужно решить контрольную?

Look at other dictionaries:

  • Asynchronous serial communication — describes an asynchronous, serial transmission protocol in which a start signal is sent prior to each byte, character or code word and a stop signal is sent after each code word. The start signal serves to prepare the receiving mechanism for the… …   Wikipedia

  • Data transmission — Data transmission, digital transmission, or digital communications is the physical transfer of data (a digital bit stream) over a point to point or point to multipoint communication channel. Examples of such channels are copper wires, optical… …   Wikipedia

  • Synchronization — Synchrony redirects here. For linguistic synchrony, see Synchronic analysis. For the X Files episode, see Synchrony (The X Files). For similarly named concepts, see Synchronicity (disambiguation). Not to be confused with data… …   Wikipedia

  • Serial communication — In telecommunication and computer science, serial communication is the process of sending data one bit at one time, sequentially, over a communication channel or computer bus. This is in contrast to parallel communication, where several bits are… …   Wikipedia

  • Synchronization (computer science) — In computer science, synchronization refers to one of two distinct but related concepts: synchronization of processes, and synchronization of data. Process synchronization refers to the idea that multiple processes are to join up or handshake at… …   Wikipedia

  • 56 kbit/s modem — 56k modems are voiceband modems nominally capable of download speeds up to 56 kbit/s (56,000 bits per second). At the beginning of the 21st Century, most personal computers contained one, their use declining as broadband technologies such as DSL… …   Wikipedia

  • Code division multiple access — This article is about a channel access method. For the mobile phone technology referred to as CDMA, see IS 95 and CDMA2000. Multiplex techniques Circuit mode (constant bandwidth) TDM · FDM  …   Wikipedia

  • Static random access memory — (SRAM) is a type of semiconductor memory where the word static indicates that, unlike dynamic RAM (DRAM), it does not need to be periodically refreshed, as SRAM uses bistable latching circuitry to store each bit. SRAM exhibits data remanence,cite …   Wikipedia

  • Interrupt — This article is about computer interrupts. For the study of the effect of disruptions on job performance, see Interruption science. In computing, an interrupt is an asynchronous signal indicating the need for attention or a synchronous event in… …   Wikipedia

  • Symbol rate — In digital communications, symbol rate (also known as baud or modulation rate) is the number of symbol changes (waveform changes or signalling events) made to the transmission medium per second using a digitally modulated signal or a line code.… …   Wikipedia

Share the article and excerpts

Direct link
Do a right-click on the link above
and select “Copy Link”