Centrifugal fan

Centrifugal fan
Figure 1: Components of a centrifugal fan
Figure 2: Centrifugal fan

A centrifugal fan (also blower, or squirrel-cage fan, as it looks like a hamster wheel) is a mechanical device for moving air or other gases. It has a fan wheel composed of a number of fan blades, or ribs, mounted around a hub. As shown in Figure 1, the hub turns on a driveshaft that passes through the fan housing. The gas enters from the side of the fan wheel, turns 90 degrees and accelerates due to centrifugal force as it flows over the fan blades and exits the fan housing.[1]

Centrifugal fans can generate pressure increases in the gas stream. Accordingly, they are well-suited for industrial processes and air pollution control systems. They are also common in central heating/cooling systems.

The centrifugal fan was invented by Russian military engineer Alexander Sablukov in 1832, and found its usage both in the Russian light industry (such as sugar making) and abroad.[2]

Contents

Fan components

The major components of a typical centrifugal fan include the fan wheel, fan housing, drive mechanism, and inlet and/or outlet dampers.

Types of drive mechanisms

The fan drive determines the speed of the fan wheel (impeller) and the extent to which this speed can be varied. There are three basic types of fan drives.[1]

Direct drive

The fan wheel can be linked directly to the shaft of an electric motor. This means that the fan wheel speed is identical to the motor's rotational speed. With this type of fan drive mechanism, the fan speed cannot be varied unless the motor speed is adjustable. Often the motor has several electric wires. Air conditioning will then automatically provide faster speed because colder air is more dense.

Belt drive

A set of sheaves are mounted on the motor shaft and the fan wheel shaft, and a belt transmits the mechanical energy from the motor to the fan.

The fan wheel speed depends upon the ratio of the diameter of the motor sheave to the diameter of the fan wheel sheave and can be obtained from this equation:[1]

rpm_{fan} = rpm_{motor}\,\bigg(\frac{\,D_{motor}}{D_{fan}}\bigg)

where:  
rpmfan = fan wheel speed, revolutions per minute
rpmmotor = motor nameplate speed, revolutions per minute
Dmotor = diameter of the motor sheave
Dfan = diameter of the fan wheel sheave

Fan wheel speeds in belt-driven fans are fixed unless the belts slip. Belt slippage can reduce the fan wheel speed several hundred revolutions per minute (rpm).

Variable drive

Variable drive fans use hydraulic or magnetic couplings (between the fan wheel shaft and the motor shaft) that allow control of the fan wheel speed independent of the motor speed. The fan speed controls are often integrated into automated systems to maintain the desired fan wheel speed.[1]

An alternate method of varying the fan speed is by use of an electronic variable-speed drive which controls the speed of the motor driving the fan. This offers better overall energy efficiency at reduced speeds than mechanical couplings.


Bearings

Bearings are an important part of a fan.

Sleeve-ring oil bearings are used extensively in fans. Some sleeve-ring bearings may be water-cooled. Water-cooled Sleeve bearings are used when hot gases are being moved by the fan. Heat is conducted through the shaft and into the oil which must be cooled to prevent overheating of the bearing.

Since lower speed fans which have a bearings in tough-to-get-to spots, Grease-packed anti-friction bearings are used.

Fan dampers and Vanes

Fan dampers are used to control gas flow into and out of the centrifugal fan. They may be installed on the inlet side or on the outlet side of the fan, or both. Dampers on the outlet side impose a flow resistance that is used to control gas flow. Dampers on the inlet side (inlet vanes) are designed to control gas flow by changing the amount of gas or air admitted to the fan inlet.

Inlet dampers (Inlet vanes) reduce fan energy usage due to their ability to affect the airflow pattern into the fan.[1]

Fan ribs

Figure 3: Centrifugal fan blades

The fan wheel consists of a hub on which a number of fan blades are attached. The fan blades on the hub can be arranged in three different ways: forward-curved, backward-curved or radial.[1]

Forward-curved blades

Forward-curved blades, as in Figure 3(a), use blades that curve in the direction of the fan wheel's rotation. These are especially sensitive to particulates. Forward-curved blades are for high flow, low pressure applications.[citation needed]

Backward-curved blades

Backward-curved blades, as in Figure 3(b), use blades that curve against the direction of the fan wheel's rotation. The backward curvature mimics that of an airfoil cross section and provides good operating efficiency with relatively economical construction techniques. These types of fan wheels are used in fans designed to handle gas streams with low to moderate particulate loadings[citation needed]. They can be easily fitted with wear protection but certain blade curvatures can be prone to solids build-up.[citation needed]

Backward curved fans can have a high range of specific speeds but are most often used for medium specific speed applications-- high pressure, medium flow applications.[citation needed]

Backward-curved fans are much more energy efficient than radial blade fans and so, for high power applications may be a suitable alternative to the lower cost radial bladed fan.[citation needed]

Straight radial blades

Radial fan blades, as in Figure 3(c), extend straight out from the hub. A radial blade fan wheel is often used on particulate-laden gas streams because it is the least sensitive to solids build-up on the blades, but it is often characterized by greater noise output. High speeds, low volumes, and high pressures are common with radial fans[citation needed], and are often used in vacuum cleaners, pneumatic material conveying systems, and similar processes.

Centrifugal fan ratings

Ratings found in centrifugal fan performance tables and curves are based on standard air SCFM. Fan manufacturers define standard air as clean, dry air with a density of 0.075 pounds mass per cubic foot (1.2 kg/m³), with the barometric pressure at sea level of 29.92 inches of mercury (101.325 kPa) and a temperature of 70 °F (21 °C). Selecting a centrifugal fan to operate at conditions other than standard air requires adjustment to both static pressure and power.

At higher than standard elevation (sea level) and higher than standard temperature, air density is lower than standard density. Air density corrections need to be taken into account for centrifugal fans that are specified for continuous operation at higher temperatures. The centrifugal fan will displace a constant volume of air in a given system regardless of the air density.

When a centrifugal fan is specified for a given CFM and static pressure at conditions other than standard, an air density correction factor must be applied to select the proper size fan to meet the new condition. Since 200 °F (93 °C) air weighs only 80% of 70 °F (21 °C) air, the centrifugal fan will create less pressure and require less power. To get the actual pressure required at 200 °F (93 °C), the designer would have to multiply the pressure at standard conditions by an air density correction factor of 1.25 (i.e., 1.0/0.8) to get the system to operate correctly. To get the actual power at 200 °F (93 °C), the designer would have to divide the power at standard conditions by the air density correction factor.

Air Movement and Control Association (AMCA)

The centrifugal fan performance tables provide the fan RPM and power requirements for the given CFM and static pressure at standard air density. When the centrifugal fan performance is not at standard conditions, the performance must be converted to standard conditions before entering the performance tables. Centrifugal fans rated by the Air Movement and Control Association (AMCA) are tested in laboratories with test setups that simulate installations that are typical for that type of fan. Usually they are tested and rated as one of four standard installation types as designated in AMCA Standard 210.[3]

AMCA Standard 210 defines uniform methods for conducting laboratory tests on housed fans to determine airflow rate, pressure, power and efficiency, at a given speed of rotation. The purpose of AMCA Standard 210 is to define exact procedures and conditions of fan testing so that ratings provided by various manufacturers are on the same basis and may be compared. For this reason, fans must be rated in SCFM.

See also

References

  1. ^ a b c d e f Fan types (U.S. Environmental Protection Agency‎ website page)
  2. ^ A History of Mechanical Fan (Russian)
  3. ^ ANSI/AMCA Standard 210-99, "Laboratory Methods Of Testing Fans for Aerodynamic Performance Rating"

Wikimedia Foundation. 2010.

Игры ⚽ Поможем написать курсовую

Look at other dictionaries:

  • Centrifugal compressor — Centrifugal compressors, sometimes termed radial compressors, are a sub class of dynamic axisymmetric work absorbing turbomachinery.[1] Centrifugal impeller with a highly polished surface likely to improve performance …   Wikipedia

  • Fan — /fan, fahn/, n., pl. Fans, (esp. collectively) Fan. Fang. * * * I Rigid or folding handheld device used for cooling, air circulation, or ceremony or as a sartorial accessory throughout the world from ancient times. As evidenced by Egyptian… …   Universalium

  • Fan — or FANS may refer to the following: Ventilation A device to agitate or move air or other gasThe human powered Fan (implement) is a hand held implement used by waving it back and forth.Motor powered Fans: mechanical fans such as oscillating fans,… …   Wikipedia

  • Fan (mechanical) — A mechanical fan is an electrically powered device used to produce an airflow for the purpose of creature comfort (particularly in the heat), ventilation, exhaust, or any other gaseous transport.Mechanically, a fan can be any revolving vane or… …   Wikipedia

  • fan — fan1 fanlike, adj. fanner, n. /fan/, n., v., fanned, fanning. n. 1. any device for producing a current of air by the movement of a broad surface or a number of such surfaces. 2. an implement of feathers, leaves, paper, cloth, etc., often in the… …   Universalium

  • Fan disk — is the part of a turbofan jet engine that contains the fan blades. It is considered one of the most critical components of the engine and has four main functions:*React to centrifugal loads from the fan blades both during normal operation and… …   Wikipedia

  • centrifugal machine — noun : a machine (as a blower, compressor, fan, filter, or separator) acting by centrifugal force * * * centrifugal machine noun A centrifuge • • • Main Entry: ↑centrifugal …   Useful english dictionary

  • fan shaped — Synonyms and related words: centrifugal, delta shaped, deltalike, deltoid, divaricate, divaricating, divergent, diverging, fan shape, fanlike, fanned, fanning, flabelliform, flared, flaring, open, outspread, outstretched, palmate, palmated,… …   Moby Thesaurus

  • Mechanical fan — Household electric box fan with a propeller style blade A mechanical fan is a machine used to create flow within a fluid, typically a gas such as air. A fan consists of a rotating arrangement of vanes or blades which act on the air. Usually, it… …   Wikipedia

  • Computer fan — A 3D illustration of four 80 mm fans, a type of fan commonly used in personal computers (sometimes as a set, or mixed with other fan sizes). A computer fan is any fan inside, or attached to, a computer case used for cooling purposes, and may… …   Wikipedia

Share the article and excerpts

Direct link
Do a right-click on the link above
and select “Copy Link”