Backflow prevention device

Backflow prevention device
In this situation, dirty water from the hillside pool will back siphon or back flow down the hosepipe and into the clean water tank. To prevent this from happening, the house's external tap should be fitted with a backflow prevention device.

A backflow prevention assembly is used to protect water supplies from contamination or pollution.

In water supply systems, water is normally maintained at a significant pressure to enable water to flow from the tap, shower etc. When pressure fails or is reduced as may happen if a water main bursts, pipes freeze or there is unexpectedly high demand on the water system, the pressure in the pipe may be reduced and may allow contaminated water from the ground, from storage or from other sources to be drawn into the system.

Back pressure is another way that an undesirable contaminant may enter your potable water piping. Sources of back pressure may be pumps in the water distribution system, boilers or heat exchanging equipment and even power washing equipment. In these cases you may have an almost constant risk of overcoming the static water pressure in the piping and when chemicals are used, as they are for commercial/industrial descaling (boilers) or residentially as in deck/siding cleaning such as bleaches (power washing), you would benefit greatly from having a backflow preventer.

To prevent such an occurrence, many regulatory regimes require there to be an air gap or mechanical backflow prevention assembly between the delivery point of mains water and local storage or use [1] Where submerged mains inflow is permitted a backflow prevention assembly is required. In this way the backflow prevention assembly protects the potable water system from contamination hazards which can be severe. There are over 10,000 reported cases of backflow contamination each year. Some cases can be fatal.

In many countries where regulations allow for the possibility of backflow, approved backflow prevention assemblies are required by law and must be installed in accordance with plumbing or building codes.

A typical backflow assembly has test cocks and shut-off valves and must be tested each year, if relocated or repaired, and when installed.

In the United States, the Environmental Protection Agency (EPA) holds local water suppliers responsible for maintaining a certain amount of purity in potable water systems. Many states and/or local municipalities require annual testing of backflow prevention assemblies. A check valve is a common form of backflow prevention. In most cases, the law requires a double check (DC), an Reduced Pressure Principle Device(RP) device or an air gap when backflow prevention is mandated.

The simplest, and most effective way to provide backflow prevention is to provide an air gap. An air gap is simply a space between any device that opens to a plumbing system (like a valve or faucet) and any place where water can collect or pool.

Partial list of backflow prevention devices

References

External links


Wikimedia Foundation. 2010.

Игры ⚽ Нужно сделать НИР?

Look at other dictionaries:

  • Reduced pressure backflow prevention assembly — A reduced pressure (RP) backflow prevention device is a device used to protect the potable water supply from contaminated water. An RP valve consists of an automatic pressure relief valve in between two check valves. The pressure relief valve… …   Wikipedia

  • Reduced pressure zone device — A Reduced Pressure Zone Device (RPZD, RPZ or RPZ valve) is a type of backflow prevention device used to protect water supplies from contamination. An RPZD is considered suitable for high hazard applications, that is, where the consequence of… …   Wikipedia

  • Fertigation — is the application of fertilizers, soil amendments, or other water soluble products through an irrigation system. Chemigation, a related and sometimes interchangeable term, is the application of chemicals through an irrigation system. Chemigation …   Wikipedia

  • Atmospheric vacuum breaker — An Atmospheric Vacuum Breaker (AVB) is a backflow prevention device used in plumbing to prevent backflow of non potable liquids into the drinking water system. It is usually constructed of brass and resembles a 90 degree elbow with a hood on its… …   Wikipedia

  • Pressure vacuum breaker — A Pressure Vacuum Breaker (PVB) is a type of backflow prevention device,used to keep non potable (or contaminated) water from entering the water supply. A PVB is similar to an atmospheric vacuum breaker (AVB), except that the PVB contains a… …   Wikipedia

  • Check valve — Tilting disc inconel check valve …   Wikipedia

  • Double check valve — A double check valve or double check assembly (DCA) is a backflow prevention device designed to protect water supplies from contamination. It is also a valve used in air brake systems on heavy trucks. Usage in Water Supply: In the case of usage… …   Wikipedia

  • Water supply network — Public infrastructure …   Wikipedia

  • Tap water — Indoor Tap commonly found in the bathroom or kitchen. This tap is a single handle, double spout tap (one spout for hot water, one spout for cold water). Tap water (running water, city water, municipal water, etc.) is a principal component of… …   Wikipedia

  • Air gap (plumbing) — An air gap, as it relates to the plumbing trade, is the unobstructed vertical space between the water outlet and the flood level of a fixture.A simple example is the space between a wall mounted faucet and the sink rim (this space is the air gap) …   Wikipedia

Share the article and excerpts

Direct link
Do a right-click on the link above
and select “Copy Link”