Drilling and blasting

Drilling and blasting

Before the advent of tunnel boring machines, drilling and blasting was the only economical way of excavating long tunnels through hard rock, where digging is not possible. Even today, the method is still used in the construction of tunnels, such as in the construction of the Lötschberg Base Tunnel. The decision whether to construct a tunnel using a TBM or using a drill and blast method includes a number of factors such as:

  • Tunnel length
  • Managing the risks of variations in ground quality
  • Required speed of construction
  • The required shape of the tunnel

Tunnel length is a key issue that needs to be addressed because large TBMs for a rock tunnel have a high capital cost, but because they are usually quicker than a drill and blast tunnel the price per metre of tunnel is lower.[1] This means that shorter tunnels tend to be less economical to construct with a TBM and are therefore usually constructed by drill and blast. Managing ground conditions can also have a significant effect on the choice with different methods suited to different hazards in the ground.

Contents

History

While drilling and blasting saw limited use in pre-industrial times using gunpowder (such as with the Blue Ridge Tunnel in the United States, built in the 1850s), it was not until more powerful (and safer) explosives, such as dynamite (patented 1867), as well as powered drills were developed, that its potential was fully realised.

Drilling and blasting was successfully used to construct tunnels throughout the world, notably the St. Gotthard Tunnel, the Jungfraubahn and even the longest road tunnel in the world, Lærdalstunnelen, are constructed using this method.

Procedure

As the name suggests, drilling and blasting works as follows:

  • A number of holes are drilled into the rock, which are then filled with explosives.
  • Detonating the explosive causes the rock to collapse.
  • Rubble is removed and the new tunnel surface is reinforced.
  • Repeating these steps will eventually create a tunnel.

The positions and depths of the holes (and the amount of explosive each hole receives) are determined by a carefully constructed pattern, which, together with the correct timing of the individual explosions, will guarantee that the tunnel will have an approximately circular cross-section.

Rock support

As the tunnel is incrementally excavated the roof and sides of the tunnel need to be supported to stop the rock falling into the excavation. The philosophy and methods for rock support vary widely but typical rock support systems can include:

  • Rock bolts or rock dowels
  • Shotcrete
  • Ribs or mining arches and lagging
  • Cable bolts
  • In-situ concrete

Typically a rock support system would include a number of these support methods, each intended to undertake a specific role in the rock support such as the combination of rock bolting and shotcrete.

References

Notes
  1. ^ Kolymbas, Dimitrios (2005). Tunelling and tunnel mechanics: a rational approach to tunnelling. Springer-Verlag. pp. 444. ISBN 3-540-25196-0. 



Wikimedia Foundation. 2010.

Игры ⚽ Поможем написать курсовую

Look at other dictionaries:

  • Drilling rig — For a detailed diagram of a Petroleum drilling rig, see List of components of oil drilling rigs. Drilling rig preparing rock blasting …   Wikipedia

  • tunnels and underground excavations — ▪ engineering Introduction        Great tunnels of the world Great tunnels of the worldhorizontal underground passageway produced by excavation or occasionally by nature s action in dissolving a soluble rock, such as limestone. A vertical opening …   Universalium

  • Tunnel and Reservoir Plan — The Tunnel and Reservoir Plan (abbreviated TARP and more commonly known as the Deep Tunnel Project or the Chicago Deep Tunnel) is a large civil engineering project that aims to reduce flooding in the metropolitan Chicago area, and to reduce the… …   Wikipedia

  • drilling machinery —       equipment used to drill holes in the ground for such activities as prospecting, well sinking (petroleum, natural gas, water, and salt), and scientific explorations. Drilling holes in rock to receive blasting charges is an operation in… …   Universalium

  • blasting —       process of reducing a solid body, such as rock, to fragments by using an explosive. Conventional blasting operations include (1) drilling holes, (2) placing a charge and detonator (blasting cap) in each hole, (3) detonating the charge, and… …   Universalium

  • Cold Regions Research and Engineering Laboratory — Established 1 February 1961 (1 February 1961) Research Type …   Wikipedia

  • Rock blasting — is the controlled use of explosives (or other methods such as gas pressure pyrotechnics or plasma processess) to excavate, break down or remove rock. It is practised most often in mining, quarrying and civil engineering such as dam or road… …   Wikipedia

  • Mold growth, assessment, and remediation — Mold assessment and mold remediation are techniques used in occupational health: mold assessment is the process of identifying the location and extent of the mold hazard in a structure, and mold remediation is the process of removal and/or… …   Wikipedia

  • Josh Lewis and Reva Shayne — Jeva (for Josh and Reva) on internet message boards. Storyline Josh Lewis and Reva Shayne met while growing up in Tulsa, Oklahoma. Reva s family worked for the wealthy Lewis clan. They were childhood sweethearts until Josh left for college.… …   Wikipedia

  • List of fictional elements, materials, isotopes and atomic particles — This list contains chemical elements, materials, isotopes or (sub)atomic particle that exist primarily in works of fiction (usually fantasy or science fiction). No actual periodic elements end in ite , though many minerals have names with this… …   Wikipedia

Share the article and excerpts

Direct link
Do a right-click on the link above
and select “Copy Link”