make+cylindrical

  • 41 Sushi — This article is about Japanese cuisine. For other uses, see Sushi (disambiguation). Different types of nigiri zushi ready to be eaten …

    Wikipedia

  • 42 Screw — This article is about the fastener. For other uses, see Screw (disambiguation). Screws come in a variety of shapes and sizes for different purposes. U.S. quarter coin (diameter 24 mm) shown for scale. A screw, or bolt, is a type of fastener… …

    Wikipedia

  • 43 Corrective lens — A bifocal corrective eyeglass lens A pair of contact le …

    Wikipedia

  • 44 sound — sound1 soundable, adj. /sownd/, n. 1. the sensation produced by stimulation of the organs of hearing by vibrations transmitted through the air or other medium. 2. mechanical vibrations transmitted through an elastic medium, traveling in air at a… …

    Universalium

  • 45 Slide rule — For other uses, see Slide rule (disambiguation). A typical ten inch student slide rule (Pickett N902 T simplex trig). The slide rule, also known colloquially as a slipstick,[1] is a mechanical analog computer. The slide rule is used primarily for …

    Wikipedia

  • 46 History of cartography — The Fra Mauro map, one of the greatest memorial of medieval cartography, was made around 1450 by the Venetian monk Fra Mauro. It is a circular world map drawn on parchment and set in a wooden frame, about two meters in diameter Cartography (from… …

    Wikipedia

  • 47 Anamorphic format — is a term that can be used either for the cinematography technique of capturing a widescreen picture on standard 35 mm film, or other visual recording media with a non widescreen native aspect ratio, or a photographic projection format in which… …

    Wikipedia

  • 48 orthopteran — /awr thop teuhr euhn/, adj. 1. orthopterous. n. 2. an orthopterous insect. [1895 1900; < NL Orthopter(a) (see ORTHOPTERON) + AN] * * * ▪ insect Introduction   broadly, any member of one of four insect orders. Orthopteran has come to be regarded… …

    Universalium

  • 49 art and architecture, Oceanic — ▪ visual arts Introduction       the visual art (art) and architecture of native Oceania, including media such as sculpture, pottery, rock art, basketry, masks, painting, and personal decoration. In these cultures, art and architecture have often …

    Universalium

  • 50 Native American music — Introduction       music of the indigenous peoples of the Western Hemisphere. The Americas contain hundreds of native communities, each with its own distinctive history, language, and musical culture. These communities although united in placing… …

    Universalium

  • 51 Castle — This article is about medieval fortifications. For other uses, see Castle (disambiguation). For a list of all castles, see List of castles. For similar but unrelated structures in Japan, see Japanese castle …

    Wikipedia

  • 52 Gear — For the gear like device used to drive a roller chain, see Sprocket. This article is about mechanical gears. For other uses, see Gear (disambiguation). Two meshing gears transmitting rotational motion. Note that the smaller gear is rotating… …

    Wikipedia

  • 53 Elevator — For other uses, see Elevator (disambiguation). A set of lifts in the lower level of a London Underground station. The arrows indicate each elevator s position and direction of travel …

    Wikipedia

  • 54 architecture — /ahr ki tek cheuhr/, n. 1. the profession of designing buildings, open areas, communities, and other artificial constructions and environments, usually with some regard to aesthetic effect. Architecture often includes design or selection of… …

    Universalium

  • 55 Carbon nanotube — Not to be confused with Carbon fiber. Part of a series of articles on Nanomaterials Fullerenes …

    Wikipedia

  • 56 Eyeglass prescription — Using a phoropter to determine a prescription for eyeglasses An eyeglass prescription is an order written by an eyewear prescriber, such as an optometrist or ophthalmologist, that specifies the value of all parameters the prescriber has deemed… …

    Wikipedia

  • 57 Milling cutter — Milling cutters are cutting tools typically used in milling machines or machining centres (and occasionally in other machine tools). They remove material by their movement within the machine (e.g., a ball nose mill) or directly from the cutter s… …

    Wikipedia

  • 58 bore — I. verb (bored; boring) Etymology: Middle English, from Old English borian; akin to Old High German borōn to bore, Latin forare to bore, ferire to strike Date: before 12th century transitive verb 1. to pierce with a turning or twisting movement… …

    New Collegiate Dictionary

  • 59 Magnet — This article is about objects and devices that produce magnetic fields. For a description of magnetic materials, see magnetism. For other uses, see Magnet (disambiguation) …

    Wikipedia

  • 60 Lathe — A lathe (pronEng|ˈleɪð) is a machine tool which spins a block of material to perform various operations such as cutting, sanding, knurling, drilling, or deformation with tools that are applied to the workpiece to create an object which has… …

    Wikipedia


We are using cookies for the best presentation of our site. Continuing to use this site, you agree with this.