- Blow molding
Blow molding (also known as blow moulding or blow forming) is a manufacturing process by which hollow plastic parts are formed. In general, there are three main types of blow molding: extrusion blow molding, injection blow molding, and stretch blow molding. The blow molding process begins with melting down the plastic and forming it into a parison or preform. The parison is a tube-like piece of plastic with a hole in one end in which compressed air can pass through.
The parison is then clamped into a mold and air is pumped into it. The air pressure then pushes the plastic out to match the mold. Once the plastic has cooled and hardened the mold opens up and the part is ejected.
History of blow molding
There has been evidence found suggesting that Egyptians and Babylonians blew plastic materials, but Enoch Ferngren and William Kopitke were the first verified people who used the blow molding process. The process principle comes from the idea of glassblowing. Ferngren and Kopitke produced a blow molding machine and sold it to Hartford Empire Company in 1937. This was the beginning of the commercial blow molding process. During the 1940s the variety and number of products was still very limited and therefore blow molding did not take off until later. Once the variety and production rates went up the number of products created followed soon afterwards. In the United States soft drink industry, the number of plastic containers went from zero in 1977 to ten billion pieces in 1999. Today, even a greater number of products are blown and it is expected to keep increasing.
For amorphous metals, also known as bulk metallic glasses (BMGs), blow molding has been recently demonstrated under pressures and temperatures comparable to plastic blow molding. This technique allows molding BMGs with an about 50 times higher strength than plastics into shapes that were previously not achievable with crystalline metals.
Typologies of blow molding
Extrusion blow molding
In extrusion blow molding (EBM), plastic is melted and extruded into a hollow tube (a parison). This parison is then captured by closing it into a cooled metal mold. Air is then blown into the parison, inflating it into the shape of the hollow bottle, container or part. After the plastic has cooled sufficiently, the mold is opened and the part is ejected. Continuous and Intermittent are two variations of Extrusion Blow Molding. In Continuous Extrusion Blow Molding the parison is extruded continuously and the individual parts are cut off by a suitable knife. In Intermittent blow molding there are two processes: straight intermittent is similar to injection molding whereby the screw turns, then stops and pushes the melt out. With the accumulator method, an accumulator gathers melted plastic and when the previous mold has cooled and enough plastic has accumulated, a rod pushes the melted plastic and forms the parison. In this case the screw may turn continuously or intermittently.
EBM processes may be either continuous (constant extrusion of the parison) or intermittent. Types of EBM equipment may be categorized as follows:
Continuous extrusion equipment
- rotary wheel blow molding systems
- shuttle machinery
Intermittent extrusion machinery
- reciprocating screw machinery
- accumulator head machinery
Examples of parts made by the EBM process include dairy containers, shampoo bottles, hoses/pipes, and hollow industrial parts such as drums.
Injection blow molding
The process of injection blow molding (IBM) is used for the production of hollow glass and plastic objects in large quantities. In the IBM process, the polymer is injection molded onto a core pin; then the core pin is rotated to a blow molding station to be inflated and cooled. This is the least-used of the three blow molding processes, and is typically used to make small medical and single serve bottles. The process is divided into three steps: injection, blowing and ejection.
The injection blow molding machine is based on an extruder barrel and screw assembly which melts the polymer. The molten polymer is fed into a manifold where it is injected through nozzles into a hollow, heated preform mold. The preform mold forms the external shape and is clamped around a mandrel (the core rod) which forms the internal shape of the preform. The preform consists of a fully formed bottle/jar neck with a thick tube of polymer attached, which will form the body.
The preform mold opens and the core rod is rotated and clamped into the hollow, chilled blow mold. The core rod opens and allows compressed air into the preform, which inflates it to the finished article shape.
After a cooling period the blow mold opens and the core rod is rotated to the ejection position. The finished article is stripped off the core rod and leak-tested prior to packing. The preform and blow mold can have many cavities, typically three to sixteen depending on the article size and the required output. There are three sets of core rods, which allow concurrent preform injection, blow molding and ejection.
Stretch blow molding
In the stretch blow molding (SBM) process, the plastic is first molded into a "preform" using the injection molding process. These preforms are produced with the necks of the bottles, including threads (the "finish") on one end. These preforms are packaged, and fed later (after cooling) into a reheat stretch blow molding machine. In the SBM process, the preforms are heated (typically using infrared heaters) above their glass transition temperature, then blown using high pressure air into bottles using metal blow molds. The preform is always stretched with a core rod as part of the process. In the single-stage process both preform manufacture and bottle blowing are performed in the same machine. The stretching of some polymers, such as PET (polyethylene terephthalate) results in strain hardening of the resin, allowing the bottles to resist deforming under the pressures formed by carbonated beverages, which typically approach 60 psi.The main applications are bottles, jars and other containers.
Advantages of blow molding include: low tool and die cost; fast production rates; ability to mold complex part; produces recyclable parts
Disadvantages of blow molding include: limited to hollow parts, wall thickness is hard to control.
Using a deformable die
To overcome problems with radial wall thickness, Harald Feuerherm patented PWDS. The system consisted of a flexible steel die that could be squeezed into a series of shapes as the moulding emerged. This gave a degree of control over wall thickness. The system is currently used to produce complex extruded shapes such as automotive fuel tanks and is used widely for UN drums and jerry cans. An enhancement of PDS is the 3DX deformable die system for radial wall thickeness control 
Containers such as jars often have an excess of material due to the molding process. This is trimmed off by spinning the container while a blade cuts the material away. This excess plastic is then recycled to create new mouldings. Spin Trimmers are used on a number of materials, such as PC, PET, PVC, HDPE, PE+LDPE and LLDPE. Different types of the materials have their own physical characteristics affecting trimming. For example, moldings produced from amorphous materials are much more difficult to trim than crystalline materials. Titanium coated blades are often used rather than standard steel to increase life by a factor of 30 times.
- ^ Jan Schroers, Thomas M. Hodges, Golden Kumar, Hari Raman, Anthony J. Barnes, Quoc Pham, Theodore A. Waniuk (February 2011). "Thermoplastic blow molding of metals". Materials Today 14: 14–19. doi:10.1016/S1369-7021(11)70018-9.
- ^ Extrusion Blow Molding Technology, Hanser Gardner Publications, ISBN 1-56990-334-4
- ^ Blow molding Guide
- ^ Harald Feuerherm Patent List
- ^ 3DX deformable die
- ^ Example of Spin Trimmer
- Lee, Norman (1990), Plastic Blow Molding Handbook, Van Nostrand Reinhold, ISBN 9780442207526.
- Lee, Norman (2006), Practical Guide to Blow Moulding, Smithers Rapra Technology, ISBN 9781859575130, http://books.google.com/books?id=blHcc6B8JO0C.
- Lee, Norman (2008), Blow Molding Design Guide (2nd ed.), Hanser-Gardner Publications, ISBN 9781569904268.
- Extrusion Blow Molding, Hanser-Gardner Publications, ISBN 1-56990-334-4
- Ottmar Brandau, Obplastics (talk) 17:35, 26 October 2011 (UTC)Stretch Blow Molding, PETplanet Publisher GmbH, ISBN 3-9807497-2-X
- Yam, K. L., "Encyclopedia of Packaging Technology", John Wiley & Sons, 2009, ISBN 978-0-470-08704-6
Wikimedia Foundation. 2010.
Look at other dictionaries:
blow molding — blowing (def. 3). * * * in glass production, method of forming an article of glass by blowing molten glass into a mold. This operation is performed with the aid of a hollow metal tube that has a mouthpiece at one end. A gob of molten glass… … Universalium
blow molding — noun : blowing 4 * * * blowing (def. 3). * * * blow molding, a process for forming hollow articles of plastic or similar materials in which the plastic is placed inside a mold and forced outward against the mold by compressed air … Useful english dictionary
Rotary wheel blow molding systems — are used for the high output production of a wide variety of plastic extrusion blow molded articles. Containers may be produced from small, single serve bottles to large containers up to 20 30 liters in volume but wheel machines are often sized… … Wikipedia
Molding (process) — One half of a bronze mold for casting a socketed spear head dated to the period 1400 1000 BC. There are no known parallels for this mold … Wikipedia
Reciprocating screw machinery — is used for the extrusion blow molding of hollow containers. Examples of parts manufactured from these machines include lightweight HDPE bottles for dairy and water, as well as large 3 5 gallon polycarbonate bottles for water coolers. Description … Wikipedia
plastic — plastically, plasticly, adv. /plas tik/, n. 1. Often, plastics. any of a group of synthetic or natural organic materials that may be shaped when soft and then hardened, including many types of resins, resinoids, polymers, cellulose derivatives,… … Universalium
Accumulator head machinery — [Accumulator Head Machinery is used for the extrusion blow molding of large industrial hollow parts. Examples of parts produced on this machinery include drums, trash cans, automotive panels, playground equipment, and large containers, such as… … Wikipedia
Shuttle machinery — Shuttle machines are a significant workhorse in the extrusion blow molding of hollow plastic articles such as bottles for food storage. Description s to be blown and cooled to the side, without interfering with the parisons, which are continually … Wikipedia
Bottle — This article is about bottles in general. For baby bottles, see Baby bottle. Composite body, painted, and glazed bottle. Dated 16th century. From Iran. New York Metropolitan Museum of Art … Wikipedia
Molded pulp — Molded pulp, also named Moulded pulp or Molded Fibre, is a packaging material, typically made from recycled paperboard and/or newsprint. It is used for protective packaging or for food service trays and beverage carriers. Other typical uses are… … Wikipedia