# Microstrip

﻿
Microstrip
Cross-section of microstrip geometry. Conductor (A) is separated from ground plane (D) by dielectric substrate (C). Upper dielectric (B) is typically air.

Microstrip is a type of electrical transmission line which can be fabricated using printed circuit board technology, and is used to convey microwave-frequency signals. It consists of a conducting strip separated from a ground plane by a dielectric layer known as the substrate. Microwave components such as antennas, couplers, filters, power dividers etc. can be formed from microstrip, the entire device existing as the pattern of metallization on the substrate. Microstrip is thus much less expensive than traditional waveguide technology, as well as being far lighter and more compact. Microstrip was developed by ITT laboratories as a competitor to stripline (first published by Grieg and Engelmann in the December 1952 IRE proceedings[1]).

The disadvantages of microstrip compared with waveguide are the generally lower power handling capacity, and higher losses. Also, unlike waveguide, microstrip is not enclosed, and is therefore susceptible to cross-talk and unintentional radiation.

For lowest cost, microstrip devices may be built on an ordinary FR-4 (standard PCB) substrate. However it is often found that the dielectric losses in FR4 are too high at microwave frequencies, and that the dielectric constant is not sufficiently tightly controlled. For these reasons, an alumina substrate is commonly used.

On a smaller scale, microstrip transmission lines are also built into monolithic microwave integrated circuits.

Microstrip lines are also used in high-speed digital PCB designs, where signals need to be routed from one part of the assembly to another with minimal distortion, and avoiding high cross-talk and radiation.

Microstrip is very similar to stripline and coplanar waveguide,[citation needed] and it is possible to integrate all three on the same substrate.

## Inhomogeneity

The electromagnetic wave carried by a microstrip line exists partly in the dielectric substrate, and partly in the air above it. In general, the dielectric constant of the substrate will be different (and greater) than that of the air, so that the wave is travelling in an inhomogeneous medium. In consequence, the propagation velocity is somewhere between the speed of radio waves in the substrate, and the speed of radio waves in air. This behaviour is commonly described by stating the effective dielectric constant (or effective relative permittivity) of the microstrip; this being the dielectric constant of an equivalent homogeneous medium (i.e. one resulting in the same propagation velocity).

Further consequences of an inhomogeneous medium include:

• The line will not support a true TEM wave; at non-zero frequencies, both the E and H fields will have longitudinal components (a hybrid mode).[2] The longitudinal components are small however, and so the dominant mode is referred to as quasi-TEM.
• The line is dispersive. With increasing frequency, the effective dielectric constant gradually climbs towards that of the substrate, so that the phase velocity gradually decreases.[2][3] This is true even with a non-dispersive substrate material (the substrate dielectric constant will usually fall with increasing frequency).
• The characteristic impedance of the line changes slightly with frequency (again, even with a non-dispersive substrate material). The characteristic impedance of non-TEM modes is not uniquely defined, and depending on the precise definition used, the impedance of microstrip either rises, falls, or falls then rises with increasing frequency.[4] The low-frequency limit of the characteristic impedance is referred to as the quasi-static characteristic impedance, and is the same for all definitions of characteristic impedance.
• The wave impedance varies over the cross-section of the line.

## Characteristic Impedance

A closed-form approximate expression for the quasi-static characteristic impedance of a microstrip line was developed by Wheeler:[5][6][7]

$Z_\textrm{microstrip} = \frac{Z_{0}}{2 \pi \sqrt{2 (1 + \varepsilon_{r})}} \mathrm{ln}\left( 1 + \frac{4 h}{w_\textrm{eff}} \left( \frac{14 + \frac{8}{\varepsilon_{r}}}{11} \frac{4 h}{w_\textrm{eff}} + \sqrt{\left( \frac{14 + \frac{8}{\varepsilon_{r}}}{11} \frac{4 h}{w_\textrm{eff}}\right)^{2} + \pi^{2} \frac{1 + \frac{1}{\varepsilon_{r}}}{2}}\right)\right)$

where weff is the effective width, which is the actual width of the strip, plus a correction to account for the non-zero thickness of the metallization. The effective width is given by

$w_\textrm{eff} = w + t \frac{1 + \frac{1}{\varepsilon_{r}}}{2 \pi} \mathrm{ln}\left( \frac{4 e}{\sqrt{\left( \frac{t}{h}\right)^{2} + \left( \frac{1}{\pi} \frac{1}{\frac{w}{t} + \frac{11}{10}}\right)^{2}}}\right)$

with

Z0 = impedance of free space,
εr = dielectric constant of substrate,
w = width of strip,
h = thickness ('height') of substrate and
t = thickness of strip metallization.

This formula is asymptotic to an exact solution in three different cases

1. $w \gg h$, any εr (parallel plate transmission line),
2. $w \ll h$, εr = 1 (wire above a ground-plane) and
3. $w \ll h$, $\varepsilon_{r} \gg 1.$

It is claimed that for most other cases, the error in impedance is less than 1%, and is always less than 2%.[7] By covering all aspect-ratios in one formula, Wheeler 1977 improves on Wheeler 1965[6] which gives one formula for w / h > 3.3 and another for $w / h \le 3.3$ (thus introducing a discontinuity in the result at w / h = 3.3). Nevertheless, the 1965 paper is perhaps the more often cited. A number of other approximate formulae for the characteristic impedance have been advanced by other authors. However, most of these are applicable to only a limited range of aspect-ratios, or else cover the entire range piecewise.

Curiously, Harold Wheeler disliked both the terms 'microstrip' and 'characteristic impedance', and avoided using them in his papers.

## Bends

In order to build a complete circuit in microstrip, it is often necessary for the path of a strip to turn through a large angle. An abrupt 90° bend in a microstrip will cause a significant portion of the signal on the strip to be reflected back towards its source, with only part of the signal transmitted on around the bend. One means of effecting a low-reflection bend, is to curve the path of the strip in an arc of radius at least 3 times the strip-width.[8] However, a far more common technique, and one which consumes a smaller area of substrate, is to use a mitred bend.

Microstrip 90° mitred bend. The percentage mitre is 100x/d

To a first approximation, an abrupt un-mitred bend behaves as a shunt capacitance placed between the ground plane and the bend in the strip. Mitring the bend reduces the area of metallization, and so removes the excess capacitance. The percentage mitre is the cut-away fraction of the diagonal between the inner and outer corners of the un-mitred bend.

The optimum mitre for a wide range of microstrip geometries has been determined experimentally by Douville and James.[9] They find that a good fit for the optimum percentage mitre is given by,

$M = 100 \frac{x}{d} \% = (52 + 65 e^{- \frac{27}{20} \frac{w}{h}}) \%$

subject to $w/h \ge 0.25$ and the with the substrate dielectric constant $\varepsilon_{r} \le 25$. This formula is entirely independent of εr. The actual range of parameters for which Douville and James present evidence is $0.25 \le w/h \le 2.75$ and $2.5 \le \varepsilon_{r} \le 25$. They report a VSWR of better than 1.1 (i.e. a return better than -26dB) for any percentage mitre within 4% (of the original d) of that given by the formula. Note that for the minimum w / h of 0.25, the percentage mitre is 96%, so that the strip is very nearly cut through.

For both the curved and mitred bends, the electrical length is somewhat shorter than the physical path-length of the strip.

## References

1. ^ Grieg, D. D.; Engelmann, H. F. (Dec. 1952). "Microstrip-A New Transmission Technique for the Klilomegacycle Range". Proceedings of the IRE 40 (12): 1644 – 1650. doi:10.1109/JRPROC.1952.274144. ISSN 0096-8390.
2. ^ a b E. J. Denlinger, “A frequency dependent solution for microstrip transmission lines”; IEEE Trans. Microwave Theory Tech., vol. MTT-19, pp. 30-39, Jan. 1971.
3. ^ H. Cory, “Dispersion characteristics of microstrip lines”; IEEE Trans. Microwave Theory Tech., vol. MTT-29, pp. 59-61, Jan. 1981.
4. ^ B. Bianco, L. Panini, M. Parodi, and S. Ridetlaj “Some considerations about the frequency dependence of the characteristic impedance of uniform microstrips”: IEEE Trans. Microwave Theory Tech., vol. MTT-26, pp. 182-185, March 1978.
5. ^ H. A. Wheeler, “Transmission-line properties of parallel wide strips by a conformal-mapping approximation”, IEEE Trans. Microwave Theory Tech., vol. MTT-12, pp. 280-289, May 1964.
6. ^ a b H. A. Wheeler, “Transmission-line properties of parallel strips separated by a dielectric sheet”, IEEE Tran. Microwave Theory Tech., vol. MTT-13, pp. 172-185, Mar. 1965.
7. ^ a b H. A. Wheeler, “Transmission-line properties of a strip on a dielectric sheet on a plane”, IEEE Tran. Microwave Theory Tech., vol. MTT-25, pp. 631-647, Aug. 1977.
8. ^ T.H. Lee, Planar Microwave Engineering; Cambridge University Press, pp. 173-174, 2004.
9. ^ R. J. P. Douville and D. S. James, Experimental study of symmetric microstrip bends and their compensation; IEEE Trans. Microwave Theory Tech., vol. MTT-26, pp. 175-182, Mar. 1978.

Wikimedia Foundation. 2010.

### Look at other dictionaries:

• Microstrip — Este artículo o sección sobre ciencia necesita ser wikificado con un formato acorde a las convenciones de estilo. Por favor, edítalo para que las cumpla. Mientras tanto, no elimines este aviso puesto el 19 de diciembre de 2007. También puedes… …   Wikipedia Español

• Microstrip — HF Baugruppe (Verstärker) mit Streifenleiter Strukturen (u. a. zur Impedanzanpassung, als Bandpass, Bandsperre, Tiefpass); rechts unter der Blechlasche befindet sich ein Zirkulator …   Deutsch Wikipedia

• microstrip — noun A thing conducting strip, separated from another conductor by a layer of dielectric, used to conduct microwaves …   Wiktionary

• Microstrip — Микрострип (микрокарта с клеющим составом для приклеивания микроизображений, приобретающим липкость при увлажнении); Часть [полоска] микрофильма (отрезанная от рулона) …   Краткий толковый словарь по полиграфии

• microstrip — …   Useful english dictionary

• Microstrip antenna — In telecommunication, there are several types of microstrip antennas (also known as printed antennas) the most common of which is the microstrip patch antenna or patch antenna. A patch antenna is a narrowband, wide beam antenna fabricated by… …   Wikipedia

• Microstrip detector — A microstrip detector is a particle detector designed to consist of a large number of identical components laid out along one axis of a two dimensional structure, generally by lithography. The idea is that several components will react to a… …   Wikipedia

• microstrip line — mikrojuostelinė linija statusas T sritis radioelektronika atitikmenys: angl. microstrip line vok. Mikrostreifenleitung, f rus. микрополосковая линия, f pranc. ligne à microbande, f; ligne à microruban, f …   Radioelektronikos terminų žodynas

• coaxial-to-microstrip junction — bendraašės ir mikrojuostelinės linijų jungė statusas T sritis radioelektronika atitikmenys: angl. coaxial to microstrip junction; coaxial to microstrip transition vok. Koaxialmikrostreifenleitungsübergang, m rus. переход коаксиал микрополосковая… …   Radioelektronikos terminų žodynas

• coaxial-to-microstrip transition — bendraašės ir mikrojuostelinės linijų jungė statusas T sritis radioelektronika atitikmenys: angl. coaxial to microstrip junction; coaxial to microstrip transition vok. Koaxialmikrostreifenleitungsübergang, m rus. переход коаксиал микрополосковая… …   Radioelektronikos terminų žodynas