Critical point (thermodynamics)

Critical point (thermodynamics)
Carbon dioxide creating a fog when cooling from supercritical to critical temperature

In physical chemistry, thermodynamics, chemistry and condensed matter physics, a critical point, also called a critical state, specifies the conditions (temperature, pressure and sometimes composition) at which a phase boundary ceases to exist. There are multiple types of critical points such as vapor–liquid critical points and liquid–liquid critical points.

Contents

Pure substances: vapor–liquid critical point

The term "critical point" is sometimes used to denote specifically the vapor–liquid critical point of a material. The vapor–liquid critical point denotes the conditions above which distinct liquid and gas phases do not exist.

The vapor–liquid critical point in a pressure–temperature phase diagram is at the high-temperature extreme of the liquid–gas phase boundary. The dotted green line gives the anomalous behaviour of water.

As shown in the pure species phase diagram to the right, this is the point at which the phase boundary between liquid and gas terminates. In water, the critical point occurs at around 647 K (374 °C; 705 °F) and 22.064 MPa (3200 PSIA or 218 atm)[1].

As the critical temperature is approached, the properties of the gas and liquid phases approach one another, resulting in only one phase at the critical point: a homogeneous supercritical fluid. The heat of vaporization is zero at and beyond this critical point, so there is no distinction between the two phases. Above the critical temperature a liquid cannot be formed by an increase in pressure, but with enough pressure a solid may be formed. The critical pressure is the vapor pressure at the critical temperature. On the diagram showing the thermodynamic properties for a given substance, the point at which critical temperature and critical pressure meet is called the critical point of the substance. The critical molar volume is the volume of one mole of material at the critical temperature and pressure.

Critical properties vary from material to material, just as is the case for the melting point and boiling point. Critical properties for many pure substances are readily available in the literature. Obtaining critical properties for mixtures is somewhat more problematic.

Mathematical definition

For pure substances, there is an inflection point in the critical isotherm (or temperature contour line) on a pV diagram. This means that at the critical point:

\left(\frac{\partial p}{\partial V}\right)_T = \left(\frac{\partial^2p}{\partial V^2}\right)_T = 0

This relation can be used to evaluate two parameters for an equation of state in terms of the critical properties.

Sometimes a set of reduced properties are defined in terms of the critical properties, i.e.:[2]

T_r = T/T_c\,
p_r = p/p_c\,
V_r = \frac{V}{RT_c/p_c}\,

where Tr is the reduced temperature, pr is the reduced pressure, Vr is the reduced volume, and R is the universal gas constant.

Principle of corresponding states

Critical variables are useful for rewriting a varied equation of state into one that applies to all materials. The effect is similar to a normalizing constant. The principle of corresponding states indicates that substances at equal reduced pressures and temperatures have equal reduced volumes. This relationship is approximately true for many substances, but becomes increasingly inaccurate for large values of pr

Table of liquid–vapor critical temperature and pressure for selected substances

Substance[3][4] Critical temperature Critical pressure
Argon −122.4 °C (150.8 K) 48.1 atm (4,870 kPa)
Ammonia[5] 132.4 °C (405.6 K) 111.3 atm (11,280 kPa)
Bromine 310.8 °C (584.0 K) 102 atm (10,300 kPa)
Caesium 1,664.85 °C (1,938.00 K) 94 atm (9,500 kPa)
Chlorine 143.8 °C (417.0 K) 76.0 atm (7,700 kPa)
Ethanol 241 °C (514 K) 62.18 atm (63 bar, 6,300 kPa)
Fluorine −128.85 °C (144.30 K) 51.5 atm (5,220 kPa)
Helium −267.96 °C (5.19 K) 2.24 atm (227 kPa)
Hydrogen −239.95 °C (33.20 K) 12.8 atm (1,300 kPa)
Krypton −63.8 °C (209.4 K) 54.3 atm (5,500 kPa)
CH4 −82.3 °C (190.9 K) 45.79 atm (4,640 kPa)
Neon −228.75 °C (44.40 K) 27.2 atm (2,760 kPa)
Nitrogen −146.9 °C (126.3 K) 33.5 atm (3,390 kPa)
Oxygen −118.6 °C (154.6 K) 49.8 atm (5,050 kPa)
CO2 31.04 °C (304.19 K) 72.8 atm (7,380 kPa)
N2O 36.4 °C (309.6 K) 71.5 atm (7,240 kPa)
H2SO4 654 °C (927 K) 45.4 atm (4,600 kPa)
Xenon 16.6 °C (289.8 K) 57.6 atm (5,840 kPa)
Lithium 2,950 °C (3,220 K) 652 atm (66,100 kPa)
Mercury 1,476.9 °C (1,750.1 K) 1,720 atm (174,000 kPa)
Sulfur 1,040.85 °C (1,314.00 K) 207 atm (21,000 kPa)
Iron 8,227 °C (8,500 K)
Gold 6,977 °C (7,250 K) 5,000 atm (510,000 kPa)
Aluminium 7,577 °C (7,850 K)
Water[6][7] 373.946 °C (647.096 K) 217.7 atm (22,060 kPa)

History

The existence of a critical point was first discovered by Thomas Andrews in 1869 for carbon dioxide. He showed that CO2 could be liquefied at 31oC at a pressure of 73 atm, but not at slightly higher temperatures even under very much higher pressures (to 3000 atm).

Mixtures: liquid–liquid critical point

A plot of typical polymer solution phase behavior including two critical points: an LCST and a UCST.

The liquid–liquid critical point of a solution denotes the limit of the two-phase region of the phase diagram. In other words, this is the point at which an infinitesimal change in some thermodynamic variable such as temperature or pressure will lead to separation of the mixture into two distinct liquid phases, as shown in the polymer–solvent phase diagram to the right. Such points may also be denoted a critical solution temperature. Two types of liquid–liquid critical points are the upper critical solution temperature, or UCST, which denotes the warmest point at which cooling will induce phase separation, and the lower critical solution temperature, which denotes the coolest point at which heating will induce phase separation.

Mathematical definition

From a theoretical standpoint, the liquid–liquid critical point represents the temperature-concentration extremum of the spinodal curve (this can be seen in the figure to the right). Thus in a two-component system it must satisfy two conditions. First is the condition of the spinodal curve, which is that the second derivative of the free energy with respect to concentration must equal zero. The second condition is the extremum condition that the third derivative of the free energy with respect to concentration must also equal zero, or that the derivative of the spinodal temperature with respect to concentration must equal zero.

In renormalization group theory

According to renormalization group theory, the defining property of criticality is that the natural length scale characteristic of the structure of the physical system, the so-called correlation length ξ, becomes infinite. This effect is the cause of the critical opalescence that is seen as the liquid–liquid critical point is approached in a binary fluid mixture. There are also lines in phase space along which this happens: these are critical lines.

In equilibrium systems the critical point is reached only by tuning a control parameter precisely. However, in some non-equilibrium systems the critical point is an attractor of the dynamics in a manner that is robust with respect to system parameters, a phenomenon referred to as self-organized criticality.

The critical point is described by a conformal field theory.

See also

Footnotes

  1. ^ International Association for the Properties of Water and Steam, 2007.
  2. ^ Cengel, Yunus A.; Boles, Michael A. (2002). Thermodynamics: an engineering approach. Boston: McGraw-Hill. pp. 91–93. ISBN 0-07-121688-X. 
  3. ^ Emsley, John (1991). The Elements ((Second Edition) ed.). Oxford University Press. ISBN 0-19-855818-X. 
  4. ^ Thermodynamics: An Engineering Approach ((Fourth Edition) ed.). McGraw-Hill. 2002. pp. 824. ISBN 0-07-238332-1. 
  5. ^ http://www.engineeringtoolbox.com/ammonia-d_971.html
  6. ^ International Association for the Properties of Water and Steam, 2007.
  7. ^ "Critical Temperature and Pressure". Purdue University. http://www.chem.purdue.edu/gchelp/liquids/critical.html. Retrieved 2006-12-19. 

References

External links


Wikimedia Foundation. 2010.

Игры ⚽ Нужно сделать НИР?

Look at other dictionaries:

  • Critical point — may refer to: Critical point (mathematics) Critical point (set theory) Critical point (thermodynamics) Construction point of a ski jumping hill See also Brillouin zone Percolation thresholds …   Wikipedia

  • Critical line (thermodynamics) — In thermodynamics, a critical line is the higher dimensional equivalent of a critical point [1]. It is the locus of contiguous critical points in a phase diagram. These lines cannot occur for a single substance due to the phase rule, but they can …   Wikipedia

  • Critical variable — Critical variables are defined, for example in thermodynamics, in terms of the values of variables at the critical point. On a PV diagram, the critical point is an inflection point. Thus: For the van der Waals equation, the above yields …   Wikipedia

  • Critical points of the elements (data page) — << Chemical elements data references Contents 1 Critical point 2 References 2.1 CRC.a d 2.2 LNG 2.3 …   Wikipedia

  • Boiling point — This article is about the boiling point of liquids. For other uses, see Boiling point (disambiguation). The boiling point of an element or a substance is the temperature at which the vapor pressure of the liquid equals the environmental pressure… …   Wikipedia

  • Critical heat flux — describes the thermal limit of a phenomenon where a phase change occurs during heating (such as bubbles forming on a metal surface used to heat water), which suddenly decreases the efficiency of heat transfer, thus causing localised overheating… …   Wikipedia

  • thermodynamics — thermodynamicist, n. /therr moh duy nam iks/, n. (used with a sing. v.) the science concerned with the relations between heat and mechanical energy or work, and the conversion of one into the other: modern thermodynamics deals with the properties …   Universalium

  • Melting point — For the physical processes that takes place at the melting point, see Melting, Freezing and Crystallization The melting point of a solid is the temperature at which it changes state from solid to liquid. At the melting point the solid and liquid… …   Wikipedia

  • Triple point — In thermodynamics, the triple point of a substance is the temperature and pressure at which three phases (for example, gas, liquid, and solid) of that substance coexist in thermodynamic equilibrium.GoldBookRef | title=Triple point |file=T06502… …   Wikipedia

  • Non-equilibrium thermodynamics — Thermodynamics …   Wikipedia

Share the article and excerpts

Direct link
Do a right-click on the link above
and select “Copy Link”