Dielectric spectroscopy


Dielectric spectroscopy
A dielectric permittivity spectrum over a wide range of frequencies. The real and imaginary parts of permittivity are shown, and various processes are depicted: ionic and dipolar relaxation, and atomic and electronic resonances at higher energies. From the Dielectric spectroscopy page of the research group of Dr. Kenneth A. Mauritz.

Dielectric spectroscopy (sometimes called impedance spectroscopy), and also known as electrochemical impedance spectroscopy, measures the dielectric properties of a medium as a function of frequency.[1][2][3][4] It is based on the interaction of an external field with the electric dipole moment of the sample, often expressed by permittivity.

It is also an experimental method of characterizing electrochemical systems. This technique measures the impedance of a system over a range of frequencies, and therefore the frequency response of the system, including the energy storage and dissipation properties, is revealed. Often, data obtained by EIS is expressed graphically in a Bode plot or a Nyquist plot.

Impedance is the opposition to the flow of alternating current (AC) in a complex system. A passive complex electrical system comprises both energy dissipater (resistor) and energy storage (capacitor) elements. If the system is purely resistive, then the opposition to AC or direct current (DC) is simply resistance.

Almost any physico-chemical system, such as electrochemical cells, mass-beam oscillators, and even biological tissue possesses energy storage and dissipation properties. EIS examines them.

This technique has grown tremendously in stature over the past few years and is now being widely employed in a wide variety of scientific fields such as fuel cell testing, biomolecular interaction, and microstructural characterization. Often, EIS reveals information about the reaction mechanism of an electrochemical process: different reaction steps will dominate at certain frequencies, and the frequency response shown by EIS can help identify the rate limiting step.

Contents

Dielectric mechanisms

There are a number of different dielectric mechanisms, connected to the way a studied medium reacts to the applied field (see the figure illustration). Each dielectric mechanism is centered around its characteristic frequency, which is the reciprocal of the characteristic time of the process. In general, dielectric mechanisms can be divided into relaxation and resonance processes. The most common, starting from high frequencies, are:

Electronic polarization

This resonant process occurs in a neutral atom when the electric field displaces the electron density relative to the nucleus it surrounds.

This displacement occurs due to the equilibrium between restoration and electric forces. Electronic polarization may be understood by assuming an atom as a point nucleus surrounded by spherical electron cloud of uniform charge density.

Atomic polarization

Atomic polarization is observed when the electronic cloud is deformed under the force of the applied field, so that the negative and positive charge are formed. This is a resonant process.

Dipole relaxation

This originates from permanent and induced dipoles aligning to an electric field. Their orientation polarisation is disturbed by thermal noise (which mis-aligns the dipole vectors from the direction of the field), and the time needed for dipoles to relax is determined by the local viscosity. These two facts make dipole relaxation heavily dependent on temperature and chemical surrounding.

Ionic relaxation

Ionic relaxation comprises ionic conductivity and interfacial and space charge relaxation. Ionic conductivity predominates at low frequencies and introduces only losses to the system. Interfacial relaxation occurs when charge carriers are trapped at interfaces of heterogeneous systems. A related effect is Maxwell-Wagner-Sillars polarization, where charge carriers blocked at inner dielectric boundary layers (on the mesoscopic scale) or external electrodes (on a macroscopic scale) lead to a separation of charges. The charges may be separated by a considerable distance and therefore make contributions to the dielectric loss that are orders of magnitude larger than the response due to molecular fluctuations.[1]

Dielectric relaxation

Dielectric relaxation as a whole is the result of the movement of dipoles (dipole relaxation) and electric charges (ionic relaxation) due to an applied alternating field, and is usually observed in the frequency range 102-1010 Hz. Relaxation mechanisms are relatively slow compared to resonant electronic transitions or molecular vibrations, which usually have frequencies above 1012 Hz.

Principles

Steady-state

For a redox reaction R  \leftrightarrow O + e, without mass-transfer limitation, the relationship between the current density and the electrode overpotential is given by the Butler-Volmer equation:


j_{\text{t}}=j_0\left(\exp(\alpha_{\text{o}}\,f\, \eta)-\exp(-\alpha_{\text{r}}\,f\,\eta)\right)

with

 \eta=E-E_{\text{eq}} ,\;f=F/(R\,T),\;\alpha_{\text{o}}+\alpha_{\text{r}}=1. j0 is the exchange current density and αo and αr are the symmetry factors.

Fig. 1 : Steady-state current density vs. overpotential for a redox reaction.

The curve  j_{\text{t}}\; vs.\; E is not a straight line (Fig. 1), therefore a redox reaction is not a linear system.[5]

Dynamic behavior

Faradaic impedance

Let us suppose that the Butler-Volmer relationship correctly describes the dynamic behavior of the redox reaction  :


j_{\text{t}}(t)=j_{\text{t}}(\eta(t))=j_0\,\left(\exp(\alpha_{\text{o}}\,f\, \eta(t))-\exp(-\alpha_{\text{r}}\,f\,\eta(t))\right)

Dynamic behavior of the redox reaction is characterized by the so-called charge transfer resistance defined by :


R_{\text{ct}}=\frac{1}{\partial j_{\text{t}}/\partial \eta }=
\frac{1}{f\,j_0\,\left(\alpha_{\text{o}}\,\exp(\alpha_{\text{o}}\,f\, \eta)+\alpha_{\text{r}}\,\exp(-\alpha_{\text{r}}\,f\, \eta) \right)}

The value of the charge transfer resistance changes with the overpotential. For this simplest example the Faradaic impedance is reduced to a resistance. It is worthwhile to notice that:


R_{\text{ct}} = \frac{1}{f\,j_0}

for η = 0 .

Double layer capacitance

An electrode | electrolyte interface behaves like a capacitance called electrochemical double-layer capacitance Cdl. The equivalent electrical circuit for the redox reaction taking account of the double-layer capacitance is shown in Fig. 2. Another analog circuit commonly used to model the electrochemical double-layer is called a constant phase element.

Fig. 2 : Equivalent circuit for a redox reaction without mass-transfer limitation.

The electrical impedance of this circuit is easily obtained remembering the impedance of a capacitance which is given by :


 Z_{\text{dl}}(\omega) =\frac{1}{\text{i}\,\omega\, C_{\text{dl}}}

where ω is the angular frequency of a sinusoidal signal (rd/s), and \scriptstyle{ \text{i}=\sqrt{-1}} . It is obtained :


Z(\omega)=\frac{R_{\text{t}}}{1+R_{\text{t}}\,C_{\text{dl}}\,\text{i} \,\omega}

Nyquist diagram of the impedance of the circuit shown in Fig. 3 is a semicircle with a diameter \scriptstyle{R_{\text{t}}} and an angular frequency at the apex equal to \scriptstyle{1/(R_{\text{t}}\,C_{\text{dc}})} (Fig. 3). Others representations, Bode or Black plans can be used.[6]

Fig. 3 : Electrochemists Nyquist diagram of a RC parallel circuit. The arrow indicates increasing angular frequencies.

Ohmic resistance

The ohmic resistance RΩ appears in series with the electrode impedance of the reaction and the Nyquist diagram is translated to the right.

Measurement of the impedance parameters

Plotting the Nyquist diagram with a potentiostat [7] and an impedance analyzer, most often included in modern potentiostats, allows the user to determine charge transfer resistance, double layer capacitance and ohmic resistance. The exchange current density j0 can be easily determined measuring the impedance of a redox reaction for η = 0.

Nyquist diagrams are made of several arcs for reaction more complex than redox reaction and with mass-transfer limitation.

See also

References

  1. ^ a b Kremer F., Schonhals A., Luck W. Broadband Dielectric Spectroscopy. – Springer-Verlag, 2002.
  2. ^ Sidorovich A. M., Dielectric Spectrum of Water. – Ukrainian Physical Journal, 1984, vol. 29, No 8, p. 1175-1181 (In Russian).
  3. ^ Hippel A. R. Dielectrics and Waves. – N. Y.: John Willey & Sons, 1954.
  4. ^ Volkov A. A., Prokhorov A. S., Broadband Dielectric Spectroscopy of Solids. – Radiophysics and Quantum Electronics, 2003, vol. 46, Issue 8, p. 657–665.
  5. ^ Linear vs. non-linear systems in impedance measurements[dead link]
  6. ^ "Potentiostat stability mystery explained" (PDF). http://www.bio-logic.info/potentiostat/notes/Application%20note%204.pdf. Retrieved 2011-11-08. 
  7. ^ Impedance, admittance, Nyquist, Bode, Black, etc.

Wikimedia Foundation. 2010.

Look at other dictionaries:

  • Dielectric relaxation — is the momentary delay (or lag) in the dielectric constant of a material. This is usually caused by the delay in molecular polarization with respect to a changing electric field in a dielectric medium (e.g. inside capacitors or between two large… …   Wikipedia

  • Dielectric — A dielectric is an electrical insulator that can be polarized by an applied electric field. When a dielectric is placed in an electric field, electric charges do not flow through the material, as in a conductor, but only slightly shift from their …   Wikipedia

  • Dielectric dispersion — In physics, dielectric dispersion is the dependence of the permittivity of a dielectric material on the frequency of an applied electric field. Because there is always a lag between changes in polarization and changes in an electric field, the… …   Wikipedia

  • High-k dielectric — The term high κ dielectric refers to a material with a high dielectric constant (κ) (as compared to silicon dioxide) used in semiconductor manufacturing processes which replaces the silicon dioxide gate dielectric. The implementation of high κ… …   Wikipedia

  • Deep-level transient spectroscopy — (DLTS) is an experimental tool for studying electrically active defects (known as charge carrier traps) in semiconductors. DLTS establishes fundamental defect parameters and measures their concentration in the material. Some of the parameters are …   Wikipedia

  • Force spectroscopy — is a dynamic analytical technique that allows the study of the mechanical properties of single polymer molecules or proteins, or individual chemical bonds. It is performed by pulling on the system under scrutiny with controlled forces. As a… …   Wikipedia

  • Nuclear magnetic resonance spectroscopy of proteins — (usually abbreviated protein NMR) is a field of structural biology in which NMR spectroscopy is used to obtain information about the structure and dynamics of proteins. The field was pioneered by Richard R. Ernst and Kurt Wüthrich[1], among… …   Wikipedia

  • Permittivity — A dielectric medium showing orientation of charged particles creating polarization effects. Such a medium can have a higher ratio of electric flux to charge (permittivity) than empty space In electromagnetism, absolute permittivity is the measure …   Wikipedia

  • List of materials analysis methods — List of materials analysis methods: Contents: Top · 0–9 · A B C D E F G H I J K L M N O P Q R S T U V W X Y Z μSR see Muon spin spectroscopy …   Wikipedia

  • Maxwell–Wagner–Sillars polarization — In dielectric spectroscopy, large frequency dependent contributions to the dielectric response, especially at low frequencies, may come from build ups of charge. This, so called Maxwell Wagner Sillars polarization (or often just Maxwell Wagner… …   Wikipedia