- Clock skew
In circuit design
In circuit designs, clock skew (sometimes timing skew) is a phenomenon in synchronous circuits in which the clock signal (sent from the clock circuit) arrives at different components at different times. This can be caused by many different things, such as wire-interconnect length, temperature variations, variation in intermediate devices, capacitive coupling, material imperfections, and differences in input capacitance on the clock inputs of devices using the clock. As the clock rate of a circuit increases, timing becomes more critical and less variation can be tolerated if the circuit is to function properly.
There are two types of clock skew: negative skew and positive skew. Positive skew occurs when the transmitting register receives the clock earlier than the receiving register. Negative skew is the opposite: the receiving register gets the clock earlier than the sending register.
Two types of violation can be caused by clock skew. One problem is caused when the clock travels more slowly than the path from one register to another - allowing data to penetrate two registers in the same clock tick, or maybe destroying the integrity of the latched data. This is called a hold violation because the previous data is not held long enough at the destination flip-flop to be properly clocked through. Another problem is caused if the destination flip-flop receives the clock tick earlier than the source flip-flop - the data signal has that much less time to reach the destination flip-flop before the next clock tick. If it fails to do so, a setup violation occurs, so-called because the new data was not set up and stable before the next clock tick arrived. A hold violation is more serious than a setup violation because it cannot be fixed by increasing the clock period. Positive skew and negative skew cannot negatively impact setup and hold timing constraints respectively (see inequalities below).
Clock skew can also benefit a circuit by increasing the clock period locally at which the circuit will operate correctly. For each source register and destination register connected by a path, the following inequalities must hold:
- T is the clock period,
- reg is the source register's clock to Q delay,
- pathmax is the path with the longest delay from source to destination,
- S is the setup time of the destination register
- pathmin is the path with the shortest delay from source to destination,
- H is the hold time of the destination register,
- (sd − ss) represents the clock skew from the source to the destination registers,
- sd is the clock skew to the destination register, and
- ss is the clock skew to the source register.
Positive clock skews are good for fixing setup violations, but can cause hold violations.
On a network
On a network such as the internet, clock skew describes the difference in time shown by the clocks at the different nodes on the network. It is usually an unavoidable phenomenon (at least if one looks at milli-second resolutions), but clock skew of tens of minutes or more is also quite common. Network operations that require time stamps which are comparable across hosts can be affected by clock skew. A number of protocols (e.g. Network Time Protocol) have been designed to reduce clock skew, and produce more stable functions. Some applications (such as game servers) may also use their own synchronization mechanism to avoid reliability problems due to clock skew.
- Friedman, E.G., ed., Clock Distribution Networks in VLSI Circuits and Systems, IEEE Press, 1995.
- Maheshwari, N., and Sapatnekar, S.S., Timing Analysis and Optimization of Sequential Circuits, Kluwer, 1999.
- Tam, S., Limaye, D.L., and Desai, U.N., "Clock Generation and Distribution for the 130-nm Itanium 2 Processor with 6-MB On-Die L3 Cache", in IEEE Journal of Solid-State Circuits, Vol. 39, No. 4, April 2004.
Wikimedia Foundation. 2010.
Look at other dictionaries:
Clock drift — refers to several related phenomena where a clock does not run at the exact right speed compared to another clock. That is, after some time the clock drifts apart from the other clock. This phenomenon is also used for instance in computers to… … Wikipedia
Skew — (von engl. skew „schief“, „windschief“) steht für: Skew (Elektronik), die Differenz von Signallaufzeiten in der Elektronik Skew (Hydrodynamik), eine hydrodynamische Anstellwinkelkorrektur bei Propellern Skew (Satellit), die Abweichung des… … Deutsch Wikipedia
Clock synchronization — is a problem from computer science and engineering which deals with the idea that internal clocks of several computers may differ. Even when initially set accurately, real clocks will differ after some amount of time due to clock drift, caused by … Wikipedia
Skew (Elektronik) — Mit dem englischen Begriff Skew, in Deutsch sinngemäß Zeitversatz, bezeichnet in der Elektronik die Zeitdifferenz von Signalen auf verschiedenen Leitungswegen. Signale, die in einem elektronischen System übermittelt werden, wandern mit einer… … Deutsch Wikipedia
Clock distribution network — In a synchronous digital system, the clock signal is used to define a time reference for the movement of data within that system. The clock distribution network (or clock tree, when this network forms a tree) distributes the clock signal(s) from… … Wikipedia
Clock signal — In electronics and especially synchronous digital circuits, a clock signal is a particular type of signal that oscillates between a high and a low state and is utilized like a metronome to coordinate actions of circuits. Although the word signal… … Wikipedia
Digital Clock Manager — is a function for manipulating clock signals by:  Multiply and divide an incoming clock (DFS). Recondition a clock to, for example, ensure 50% duty cycle. Phase shift (DLL). Eliminate clock skew. See also Clock signal Delay locked loop Phase… … Wikipedia
Multi-gigabit transceiver — A Multi Gigabit Transceiver (MGT) is a SerDes capable of operating at serial bit rates above 1 Gigabit/second. MGTs are used increasingly for data communications because they can run over longer distances, use fewer wires, and thus have lower… … Wikipedia
Serielle Datenübertragung — Bei der seriellen Datenübertragung werden digitale Daten bitweise hintereinander übertragen. Im Gegensatz hierzu werden bei der parallelen Datenübertragung mehrere bits auf einmal (d.h. gleichzeitig) übertragen. Nach der Übertragung der Daten… … Deutsch Wikipedia
Bitseriell — Bei der seriellen Datenübertragung werden Daten, sofern sie digital sind, bitweise hintereinander über ein bestimmtes Medium übertragen. Es gibt verschiedene Standards, über die eine serielle Übertragung erfolgen kann. Die Auflistung einiger… … Deutsch Wikipedia