Bend radius

Bend radius
Bend radius

Bend radius, which is measured to the inside curvature, is the minimum radius one can bend a pipe, tube, sheet, cable or hose without kinking it, damaging it, or shortening its life. The smaller the bend radius, the greater is the material flexibility (as the radius of curvature decreases, the curvature increases). The diagram below illustrates a cable with a seven-centimeter bend radius.

The minimum bend radius is the radius below which an object such as a cable should not be bent.

Fiber optics

The minimum bend radius is of particular importance in the handling of fiber-optic cables, which are often used in telecommunications. The minimum bending radius will vary with different cable designs. The manufacturer should specify the minimum radius to which the cable may safely be bent during installation, and for the long term. The former is somewhat shorter than the latter. The minimum bend radius is in general also a function of tensile stresses, e.g., during installation, while being bent around a sheave while the fiber or cable is under tension. If no minimum bend radius is specified, one is usually safe in assuming a minimum long-term low-stress radius not less than 15 times the cable diameter.

Beside mechanical destruction, another reason why one should avoid excessive bending of fiber-optic cables is to minimize microbending and macrobending losses. Microbending causes light attenuation induced by deformation of the fiber while macrobending causes the leakage of light through the fiber cladding and this is more likely to happen where the fiber is excessively bent.

Other applications

Strain gauges also have a minimum bending radius. This radius is the radius below which the strain gauge will malfunction.

References

 This article incorporates public domain material from the General Services Administration document "Federal Standard 1037C".


Wikimedia Foundation. 2010.

Игры ⚽ Нужна курсовая?

Look at other dictionaries:

  • Bend radius — Bend radius. См. Радиус изгиба. (Источник: «Металлы и сплавы. Справочник.» Под редакцией Ю.П. Солнцева; НПО Профессионал , НПО Мир и семья ; Санкт Петербург, 2003 г.) …   Словарь металлургических терминов

  • bend radius — F/A/V maximum amount a conductor can be bent before excessive attenuation is encountered, signal integrity is compromised, or the conductor breaks …   Audio and video glossary

  • Minimum bend radius — Minimum bend radius. См. Минимальный угол изгиба. (Источник: «Металлы и сплавы. Справочник.» Под редакцией Ю.П. Солнцева; НПО Профессионал , НПО Мир и семья ; Санкт Петербург, 2003 г.) …   Словарь металлургических терминов

  • Bend — may refer to:* Bend, Oregon, a city * Bend, an album by 8stops7 * Bend (heraldry), a colored band that runs from the upper left (as seen by the viewer) corner of the shield to the lower right * Decompression sickness, commonly the bends * The… …   Wikipedia

  • Radius (disambiguation) — A radius is a straight line from the center to the boundary of a geometric object, especially a circle, sphere, or disk.Radius may also refer to:* Any of several concepts closely related to the above, including ** Radius of curvature, a measure… …   Wikipedia

  • Radius — For other uses, see Radius (disambiguation). Circle illustration In classical geometry, a radius of a circle or sphere is any line segment from its center to its perimeter. By extension, the radius of a circle or sphere is the length of any such… …   Wikipedia

  • Radius of curvature (applications) — The distance from the center of a sphere or ellipsoid to its surface is its radius. The equivalent surface radius that is described by radial distances at points along the body s surface is its radius of curvature (more formally, the radius of… …   Wikipedia

  • Radius of bend — Radius of bend. См. Радиус изгиба. (Источник: «Металлы и сплавы. Справочник.» Под редакцией Ю.П. Солнцева; НПО Профессионал , НПО Мир и семья ; Санкт Петербург, 2003 г.) …   Словарь металлургических терминов

  • Radius of curvature — Curvature Cur va*ture (k?r v? t?r; 135), n. [L. curvatura. See {Curvate}.] 1. The act of curving, or the state of being bent or curved; a curving or bending, normal or abnormal, as of a line or surface from a rectilinear direction; a bend; a… …   The Collaborative International Dictionary of English

  • bend test — a test sometimes made to indicate ductility or bending quality by bending a suitable specimen about a predetermined radius through a predetermined angle …   Mechanics glossary

Share the article and excerpts

Direct link
Do a right-click on the link above
and select “Copy Link”