 Military grid reference system

Geodesy Fundamentals Geodesy · Geodynamics
Geomatics · CartographyConcepts Datum · Distance · Geoid
Figure of the Earth
Geodetic system
Geog. coord. system
Hor. pos. representation
Map projection
Reference ellipsoid
Satellite geodesy
Spatial reference systemTechnologies GNSS · GPS · ... Standards ED50 · ETRS89 · NAD83
NAVD88 · SAD69 · SRID
UTM · WGS84 · ...History History of geodesy
NAVD29 · ...v · NATO militaries for locating points on the earth. The MGRS is derived from the UTM (Universal Transverse Mercator) grid system and the UPS (Universal Polar Stereographic) grid system, but uses a different labeling convention. The MGRS is used for the entire earth. An example of an MGRS coordinate, or grid reference, would be 4QFJ12345678, which consists of three parts:
 4Q (grid zone designator, GZD),
 FJ (the 100,000meter square identifier), and
 12345678 (numerical location; easting is 1234 and northing is 5678, in this case specifying a location with 10m resolution).
An MGRS grid reference is a point reference system. When the term 'grid square' is used, it can refer to a square with a side length of 10 km, 1 km, 100 m, 10 m or 1 m, depending on the precision of the coordinates provided. (In some cases, squares adjacent to a Grid Zone Junction (GZJ) are clipped, so polygon is a better descriptor of these areas.) The number of digits in the numerical location must be even: 0, 2, 4, 6, 8 or 10, depending on the desired precision. When changing precision levels, it is important to truncate rather than round the easting and northing values to ensure the more precise polygon will remain within the boundaries of the less precise polygon. Related to this is the primacy of the southwest corner of the polygon being the labeling point for an entire polygon. In instances where the polygon is not a square and has been clipped by a grid zone junction, the polygon keeps the label of the southwest corner as if it had not been clipped.
 4Q ...................GZD only, precision level 6° × 8° (in most cases)
 4QFJ .................GZD and 100 km SQ_ID, precision level 100 km
 4QFJ16 ...............precision level 10 km
 4QFJ1267 .............precision level 1 km
 4QFJ123678 ...........precision level 100 m
 4QFJ12346789 .........precision level 10 m
 4QFJ1234567890 .......precision level 1 m
Such an MGRS coordinate, standing alone, may be converted to latitude and longitude. But you still do not know the position on the Earth, unless you also know the geodetic datum that is used.
Contents
Grid zone designation
The first part of an MGRS coordinate is the gridzone designation. The 6° wide UTM zones, numbered 1–60, are intersected by latitude bands that are normally 8° high, lettered C–X (omitting I and O). The northmost latitude band, X, is 12° high. The intersection of a UTM zone and a latitude band is (normally) a 6° × 8° polygon called a grid zone, whose designation in MGRS is formed by the zone number (one or two digits  the number for zones 1 to 9 is just a single digit, according to the example in DMA TM 8358.1, Section 32,^{[1]} Figure 7), followed by the latitude band letter (uppercase). This same notation is used in both UTM and MGRS, i.e. the UTM grid reference system; the article on Universal Transverse Mercator shows many maps of these grid zones, including the irregularities for Svalbard and southwest Norway. As Figure 1 illustrates, Honolulu is in grid zone 4Q.
100,000meter square identification
The second part of an MGRS coordinate is the 100,000meter square identification. Each UTM zone is divided into 100,000 meter squares, so that their corners have UTMcoordinates that are multiples of 100,000 meters. The identification consists of a column letter (A–Z, omitting I and O) followed by a row letter (A–V, omitting I and O).
Near the equator, the columns of UTM zone 1 have the letters A–H, the columns of UTM zone 2 have the letters J–R (omitting O), and the columns of UTM zone 3 have the letters S–Z. At zone 4, the column letters start over from A, and so on around the world.
For the row letters, there are actually two alternative lettering schemes within MGRS:
 In the AA scheme,^{[2]} also known as MGRSNew,^{[3]} which is used for WGS84 and some other modern geodetic datums, the letter for the first row – just north of the equator – is A in oddnumbered zones, and F in evennumbered zones, as shown in figure 1. Note that the westmost square in this row, in zone 1, has identification AA.
 In the alternative AL scheme,^{[2]} also known as MGRSOld,^{[3]} which is used for some older geodetic datums, the row letters are shifted 10 steps in the alphabet. This means that the letter for the first row is L in oddnumbered zones and R in evennumbered zones. The westmost square in the first row, in zone 1, has identification AL.
If an MGRS coordinate is complete (with both a grid zone designation and a 100,000 meter square identification), and is valid in one lettering scheme, then it is usually invalid in the other scheme, which will have no such 100,000 meter square in the grid zone. (Latitude band X is the exception to this rule.) Therefore, a position reported in a modern datum usually can not be misunderstood as using an old datum, and vice versa – provided the datums use different MGRS lettering schemes.
In the map (figure 1), which uses the AA scheme, we see that Honolulu is in grid zone 4Q, and square FJ. To give the position of Honolulu with 100 km resolution, we write 4QFJ.
Numerical location
The third part of an MGRS coordinate is the numerical location within a 100,000 meter square, given as n + n digits, where n is 1, 2, 3, 4, or 5. If 5 + 5 digits is used, the first 5 digits give the easting in meters, measured from the left edge of the square, and the last 5 digits give the northing in meters, measured from the bottom edge of the square. The resolution in this case is 1 meter, so the MGRS coordinate would represent a 1 meter square, where the easting and northing are measured to its southwest corner. If a resolution of 10 meters is enough, the final digit of the easting and northing can be dropped, so that only 4 + 4 digits are used, representing a 10 meter square. If a 100 meter resolution is enough, 3 + 3 digits suffice; if a 1 km resolution is enough, 2 + 2 digits suffice; if 10 km resolution is enough, 1 + 1 digits suffice. 10 meter resolution (4 + 4 digits) is sufficient for many purposes, and is the NATO standard for specifying coordinates.
If we zoom in on Hawaii (figure 2), we see that the square that contains Honolulu, if we use 10 km resolution, would be written 4QFJ15.
If the grid zone or 100,000meter square are clear from context, they can be dropped, and only the numerical location is specified. For example:
 If every position being located is within the same grid zone, only the 100,000meter square and numerical location are specified.
 If every position being located is within the same grid zone and 100,000meter square, only the numerical location is specified.
 However, even if every position being located is within a small area, but the area overlaps multiple 100,000meter squares or grid zones, the entire grid reference is required.
One always reads map coordinates from west to east first (easting), then from south to north (northing). Common mnemonics include "in the house, up the stairs", "lefttoright, bottomtotop" and "Read Right Up".
Truncate, don't round
As mentioned above, when converting UTM coordinates to an MGRS grid reference, or when abbreviating an MGRS grid reference to lower precision, one should truncate the coordinates, not round. This has been controversial in the past, since the oldest specification, TM8358.1,^{[1]} used rounding, as did GEOTRANS^{[4]} before version 3.0. However, truncation is used in GEOTRANS since version 3.0, and in NGA Military Map Reading 201^{[3]} (page 5) and in the US Army Field Manual 325.26.^{[5]} The civilian version of MGRS, USNG, also uses truncation.^{[6]}
Squares that cross a latitude band boundary
The boundaries of the latitude bands are parallel circles (dashed black lines in figure 1), which do not coincide with the boundaries of the 100,000meter squares (blue lines in figure 1). For example, at the boundary between grid zones 1P and 1Q, we find a 100,000meter square BT, of which about two thirds is south of latitude 16° and therefore in grid zone 1P, while one third is north of 16° and therefore in 1Q. So, an MGRS grid reference for a position in BT should begin with 1PBT in the south part of BT, and with 1QBT in the north part of BT. At least, this is possible if the precision of the grid reference is enough to place the denoted area completely inside either 1P or 1Q.
But an MGRS grid reference can denote an area that crosses a latitude band boundary. For example, when describing the entire square BT, should it be called 1PBT or 1QBT? Or when describing the 1000meter square BT8569, should it be called 1PBT8569 or 1QBT8569? In these cases, software that interprets an MGRS grid reference should accept both of the possible latitude band letters. A practical motivation was given in the release notes for GEOTRANS,^{[4]} Release 2.0.2, 1999:
The MGRS module was changed to make the final latitude check on MGRS to UTM conversions sensitive to the precision of the input MGRS coordinate string. The lower the input precision, the more "slop" is allowed in the final check on the latitude zone letter. This is to handle an issue raised by some F16 pilots, who truncate MGRS strings that they receive from the Army. This truncation can put them on the wrong side of a latitude zone boundary, causing the truncated MGRS string to be considered invalid. The correction causes truncated strings to be considered valid if any part of the square which they denote lies within the latitude zone specified by the third letter of the string.
Polar regions
In the polar regions, a different convention is used.^{[7]} South of 80°S, UPS South (Universal Polar Stereographic) is used instead of a UTM projection. The west halfcircle forms a grid zone with designation A; the east halfcircle forms one with designation B; see figure 3. North of 84°N, UPS North is used, and the west halfcircle is Y, the east one is Z; see figure 4. Since the letters A, B, Y, and Z are not used for any latitude bands of UTM, their presence in an MGRS coordinate, with the omission of a zone number, indicates that the coordinates are in the UPS system.
The lettering scheme for 100,000 m squares is slightly different in the polar regions. The row letters go from A to Z, omitting I and O. The column letters use a more restricted alphabet, going from A to Z but omitting I, O, D, E, M, N, V, W; the columns are arranged so that the rightmost column in grid zone A and Y has column letter Z, and the next column in grid zone B or Z starts over with column letter A. The restricted column alphabet for UPS ensures that no UPS square will be adjacent to a UTM square with the same identification.
In the polar regions, there is only one version of the lettering scheme.^{[7]}
See also
There are other geographic naming systems of this alphanumeric kind:
 The Global Area Reference System (GARS) has been adopted by the National GeospatialIntelligence Agency for use across the Department of Defense for certain applications. GARS defines areas of 30x30, 15x15, and no smaller than 5x5 minutes of latitude and longitude.
 United States National Grid USNG, developed by the Federal Geographic Data Committee.
 The Georef system has been used for air navigation, but is rarely seen today.
 The Maidenhead Locator System is used by amateur radio operators.
 A modification of the Military Grid Reference System is used by the Atlas Florae Europaeae for mapping the distribution of vascular plants in Europe.
 Natural Area Code
References
 ^ ^{a} ^{b} ^{c} DMA Technical Manual 8358.1, Chapter 3. Datums, Ellipsoids, Grids, and Grid Reference Systems
 ^ ^{a} ^{b} NGA Guidance for the Military Grid Reference System (MGRS).
 ^ ^{a} ^{b} ^{c} Military Map Reading 201, published by NGA
 ^ ^{a} ^{b} GEOTRANS Geographic Translator software and source code from the US National GeospatialIntelligence Agency.
 ^ Map Reading and Land Navigation, U.S. Army Field Manual No. 325.26 (see section 46).
 ^ J. Anthony Cavell, USNG: Getting it right the first time. The American Surveyor, June 2005.
 ^ ^{a} ^{b} DMA Technical Manual 8358.1, Appendix B. Datums, Ellipsoids, Grids, and Grid Reference Systems.
External links
 A list of coordinate systems – by Prof. Peter H. Dana at the Univ. of Colorado
 Grids and Reference Systems, by NGA.
 GeographicLib provides a utility GeoConvert (with source code) for conversions between geographic, UTM, UPS, and MGRS. Here is an online version of GeoConvert.
 Army Study Guide: Locate a point using the US Army Military Grid Reference System (MGRS)
Categories: Geographic coordinate systems
 Military cartography
 Geodesy
Wikimedia Foundation. 2010.
Look at other dictionaries:
military grid reference system — karinio atramos koordinačių tinklo sistema statusas T sritis Gynyba apibrėžtis Standartinio mastelio tinklo kvadratų sistema, turinti atskaitos tašką, kuri yra tiksliai ir nuosekliai išdėstyta žemėlapyje, kad būtų galima nurodyti vietą arba… … NATO terminų aiškinamasis žodynas
military grid reference system — A system which uses a standard scaled grid square, based on a point of origin on a map projection of the surface of the Earth in an accurate and consistent manner to permit either position referencing or the computation of direction and distance… … Military dictionary
militarygrid reference system — A system that uses a standard scaled grid square, based on a point of origin on a map projection of the surface of the earth in an accurate and consistent manner to permit either position referencing or the computation of direction and distance… … Aviation dictionary
military grid — Two sets of parallel lines intersecting at right angles and forming squares; the grid is superimposed on maps, charts, and other similar representations of the surface of the Earth in an accurate and consistent manner to permit identification of… … Military dictionary
Global Area Reference System — The Global Area Reference System is a standardized geospatial reference system proposed by the National Geospatial Intelligence Agency (NGA) for use across the United States Department of Defense. It is somewhat similar to the Military grid… … Wikipedia
Spatial reference system — Geodesy Fundamentals Geodesy · … Wikipedia
grid — 1. Two sets of parallel lines intersecting at right angles and forming squares; the grid is superimposed on maps, charts, and other similar representations of the Earth military grid; military grid reference system … Military dictionary
grid — i. The system of two sets of parallel lines uniformly spaced and crossing at 90° to each other to form a pattern of squares. This grid is designed so that any point on the map can be designated by its latitude and longitude or by its grid… … Aviation dictionary
Military history of Jewish Americans — Jewish Americans have served in the United States armed forces dating back to before the colonial era, when Jews have served in militias of the Thirteen Colonies. Jewish military personnel have served in all branches of the armed forces and in… … Wikipedia
Military Road (Omaha) — Military Road Segment U.S. National Register of Historic Places … Wikipedia
18+© Academic, 20002020 Contact us: Technical Support, Advertising
Dictionaries export, created on PHP, Joomla, Drupal, WordPress, MODx.We are using cookies for the best presentation of our site. Continuing to use this site, you agree with this.
Military grid reference system
 Military grid reference system

Geodesy Fundamentals Geodesy · Geodynamics
Geomatics · CartographyConcepts Datum · Distance · Geoid
Figure of the Earth
Geodetic system
Geog. coord. system
Hor. pos. representation
Map projection
Reference ellipsoid
Satellite geodesy
Spatial reference systemTechnologies GNSS · GPS · ... Standards ED50 · ETRS89 · NAD83
NAVD88 · SAD69 · SRID
UTM · WGS84 · ...History History of geodesy
NAVD29 · ...