CQBR

CQBR

The Close Quarters Battle Receiver (CQBR) is a replacement upper receiver for the M4A1 Carbine. The CQBR upgrades the M4 with a barrel 10.3 in (260 mm) long, the modern equivalent of the Colt Commando short-barrel M16 variants of the past.

Its preliminary National Stock Number was 1005-LL-L99-5996; however, a complete CQBR-equipped carbine now has the NSN 1005-01-527-2288. The overall length of the upper receiver is 19.25 inches (489 mm). With the stock retracted, the overall length of the weapon is 26.25 inches (666 mm). The CQBR entered service in 2000.

Background

The M4 and M16 are not ideally suited for all missions, so it was proposed that the modularity of the M16 series would allow a user to replace the upper receiver of an existing weapon with one more suitable to the task. One of two proposed special mission receivers that were planned for inclusion into the SOPMOD Block II kit, the CQBR has taken off on its own. Like the proposed Special Purpose Receiver, the Close Quarters Battle Receiver has been more or less taken on by the Naval Surface Warfare Center, Crane Division (often referred to as NSWC-Crane or just "Crane") as its own project following the CQBR's removal from the SOPMOD program. Just as the Special Purpose Receiver morphed into the Special Purpose Rifle, and was type-classified as Mk 12 Mod 0/1, the complete CQBR-equipped carbine has been type-classified as the Mk 18 Mod. 0.

The purpose of the CQBR remains to provide operators with a weapon of submachine gun size, but firing a rifle cartridge, for scenarios such as VIP protection, urban warfare, and other close quarters battle (CQB) situations. The CQBR is designed to provide improvement over previous AR-15/M16-type weapons in this category. The CQBR is usually issued as a complete weapon system, and not just an upper receiver. The CQBR was once only available to Naval Special Warfare units, but the Mk 18 Mod 0 has become general issue for Visit, Board, Search, and Seizure (VBSS) missions. NCIS agents deploying to active combat zones are also issued the Mk 18 as of summer 2006.Fact|date=August 2008

The short 10.3 in (262 mm) barrel length requires special modifications to reliably function. The gas port is opened from 0.062 to 0.070 in (0.16 to 0.18 mm). A one-piece McFarland gas ring replaces the three-piece gas ring set. The standard 4-coil extractor spring is replaced with a commercial off-the-shelf (COTS) 5-coil spring. An O-ring surrounds the extractor spring.

Evolution

* CQBR type 1 - Made from M4A1 uppers by shortening the barrels and opening gas ports, no longer produced, STD carbine buffer in use in host lowers at time of fielding.

* CQBR type 2 - NSWC assembled with contracted and /or overhauled parts complete with all accessories to current standards at time of build, will work with H, H2 or H3 balanced to ammo requirements:
* H ok with M193/M855.
* H2 needed for MK 262/ R2LP & will run M193/M855.
* H3 may be needed for an extreme case, or when the gas port is eroded but the barrel still groups.

* CQBR type 2A - NSWC assembled with contracted and /or overhauled parts, naked without any accessories or buffer. The buffer in the host carbine would be used or upgraded as necessary via the supply system same as type 2.

* CQBR type 3 - Colt contracted upper complete with all accessories. NO buffer supplied. The buffer in the host carbine would be used or upgraded as necessary via the supply system same as type 2.

* CQBR type 3A - Colt contracted upper naked without any accessories or buffer supplied. The buffer in the host carbine would be used or upgraded as necessary via the supply system same as type 2.

* MK18 type 1 - NSWC assembled carbine with contracted and /or overhauled parts complete with all accessories to current standards at time of build will work with H or H2 and could have shipped with either. Units will balance buffer to ammo requirements:
* H ok with M193/M855. ( all ship board MK 18’s should have H buffers as this was the standard at the time of assembly).
* H2 needed for MK 262/ R2LP & will run M193/M855
* H3 may be needed for an extreme cases or when the gas port is eroded but the barrel still groups

* MK18 type 2 - Colt contracted carbine complete with all accessories H buffer supplied. Units will balance buffer to ammo requirements same as MK18 type1.

pecifications

*Upper and lower receivers: The lower receiver is a standard M4A1 lower receiver sometimes modified with the addition of a CQD RSM sling adapter plate. However, many CQBR rifles also use surplus M16A1 lower receivers. Internally, the CQBR also takes advantage of a larger gas port and modified bolt carrier and buffer assembly. The gas port has been opened to 0.070 in (0.18 mm). A number of Lewis Machine & Tool 10.5" (266.7 mm) upper receivers have also been reported to have been purchased for the CQBR program. These upper receivers feature a gas system optimized for short barrel use.

*Sights: Initially, detachable carrying handles cut down so that only the rear sight assembly was used. However, most of these have been replaced with the similar, commercially-made Lewis Machine & Tool adjustable rear sight. Also used are several types of reflex and magnified optics, most commonly seen is the Aimpoint CompM2 in a Wilcox Industries Corp. Picatinny mount.

*Stock: A variety of M4 retractable buttstocks are used on a standard 4-position receiver extension, including the standard "CAR" stock. Most often seen is the SOPMOD stock, often referred to as the "Crane stock", created by Dave Armstrong of NSWC-Crane. The angled stock offers better cheekweld as well as providing two storage compartments for spare batteries. The stock must be removed from the weapon to access the storage compartments. The initial run of stocks was made by NSWC-Crane from glass fiber polymer. Because of this, they were somewhat fragile and did not always properly lock into the receiver extension. A rubber band was used to secure the latch so it would not slide out of the desired position. The current SOPMOD stocks are made by Lewis Machine & Tools and have none of the problems.

*Barrel: The CQBR uses a standard 1:7 in (178 mm) twist M4 barrel that has been reduced in length to 10.3 in (262 mm). The diameter of the barrel under the handguards is 1.17 in (29.7 mm). The KAC M4-QD flash suppressor is fitted, allowing use of the KAC QDSS-NT4 suppressor (National Stock Number 1005-01-437-0324). Although it has a bayonet lug, the CQBR is not meant to be fitted with any fighting blades.

*Handguards: The standard handguard for the CQBR is the Knight's Armament Company Rail Interface System (M4 Carbine RIS; National Stock Number 1005-01-416-1089), which is designed for a variety of barrel profiles and allows for the use of any MIL-STD-1913 tactical accessories such as the AN/PEQ-2 infrared pointer, SureFire flashlights or a vertical forward grip.

*Ammunition: The CQBR is designed to use standard 5.56x45mm NATO 62-grain M855 FMJ and M856 Tracer ammunition. However, due to the short barrel, the heavier 77-grain Mk 262 cartridge is preferred. There are no plans to rechamber the weapon in any additional calibers.

Photos

ee also

* AR15 and M16 rifles and M4A1 carbine
* United States Navy Mark 12 Mod 0 Special Purpose Rifle
* List of individual weapons of the U.S. Armed Forces
* Knight's Armament Company

External links

* [http://www.dtic.mil/ndia/2003smallarms/john.ppt NAVSEA CQBR PowerPoint presentation]


Wikimedia Foundation. 2010.

Игры ⚽ Нужно решить контрольную?

Look at other dictionaries:

  • Mk.18 Mod 0 CQBR — Le CQBR : un M4 à canon très court La carabine d assaut Mk 18 Mod. 0 ou CQBR (pour Close Quarter Battle Rifle (chez son fabricant) est une variante plus compacte de la Colt M4 en service dans l US Navy depuis la fin des années 2000. Données… …   Wikipédia en Français

  • Close Quarters Battle Receiver — Close Quarter Battle Receiver[1] Above: An M4A1 with SOPMOD package, including Rail Interface System and Trijicon 4x ACOG. The barrel length is 14.5 inches (370 mm). Below: An M4A1 with …   Wikipedia

  • SOPMOD — Special Operations Peculiar Modification Le programme Special Operations Peculiar Modification, ou SOPMOD, est un programme de l armée des États Unis. Il est destiné à uniformiser les armes et accessoires employés parmi les forces spéciales… …   Wikipédia en Français

  • Special Operations Peculiar Modification — Le programme Special Operations Peculiar Modification, ou SOPMOD, est un programme de l armée des États Unis. Il est destiné à uniformiser les armes et accessoires employés parmi les forces spéciales Américaines, les SOF (Forces d opérations… …   Wikipédia en Français

  • M4 carbine — M4A1 redirects here. For the World War II tank, see M4 Sherman. For the World War II rifle, see M4 Survival Rifle. Carbine, 5.56 mm, M4 An M4 with an aftermarket buttstock, Rail Adapter System (RAS), fl …   Wikipedia

  • Colt Canada C7 rifle — C7 rifle Diemaco C7A1 Assault Rifle Type Assault rifle Place of origin …   Wikipedia

  • List of firearms — This is an extensive list of small arms pistol, machine gun, grenade launcher, anti tank rifle that includes variants. 0 9*977 Bowing rifle ( Russian Rifle) *90 1000 Assault Rifle ( American Rifle) *9A 91 (Russia Carbine Assault Rifle 9 x 39… …   Wikipedia

  • Liste der Handfeuerwaffen/M — Liste der Handfeuerwaffen   A B C D E F G H I J K L M N …   Deutsch Wikipedia

  • Colt M4 — Pour les articles homonymes, voir M4. M4 Un M4 et ses accessoires Présentation P …   Wikipédia en Français

  • M16 rifle — Rifle, 5.56 mm, M16 From top to bottom: M16A1, M16A2, M4A1, M16A4 Type Assault rifle Place  …   Wikipedia

Share the article and excerpts

Direct link
Do a right-click on the link above
and select “Copy Link”