Tube tool


Tube tool

Tube tools are tools used to service any tubing (material) in industrial applications including, but not limited to: HVAC or industrial heating and air (hospitals and universities, for example), OEM's(Original equipment manufacturer), defense contractors, the automotive industry, process industries, aluminum smelting facilities, food and sugar production plants, oil refineries, and power plants.

Application

Tube Tools can be categorized into function by application:

Tube Cleaners-tube cleaning demands vary widely by applicationShell and tube heat exchangers and chillers: Deposits are typically sediment from impurities in the water circulating through the tubes. Manual scrubbing with a wire brush attached to a long rod is the traditional method of cleaning. Modern methods involve pneumatic or hydraulic motors to pulsate the brush automatically with a medium pressure water jet to further clean out residual deposits.

Tube Testers- Use air pressure or vacuum to test for leaks, cracks, and material failures in a tube. Both manual activated and air activated models are available.To test for leaks in tubes, two operators are required with an operator at each end of the vessel.Step 1 - Seal the tube at both ends.Step 2 - Build air pressure or vacuum in the tube.Step 3 - Observe gauge to see if air pressure is dropping or vacuum is not holding.

Tube Plugs(Repair)- To regain efficiency of a heat exchanger or chiller, tube plugs are installed to take leaky tubes out of service. The rule of thumb is that a vessel will need to be retubed after approximately 10% of the tubes have been plugged.Tubes need to be plugged at both ends of the pressure vessel.

It is a good practice to:Install a plug that is the same as or a compatible material to the tube and tube sheet. Puncture the leaky tube using a one revolution tube cutter to relieve back pressure. Some contractors weld the tube plugs to the tube sheet after they are installed to permanently secure the plugs in place.

Tube Removers-One or a combination of the three below methods is used to remove a tube from a boiler or chiller vessel
*Tube Cutters- Tube Cutters are used to internally cut from the inside to the outside of the tube behind the tube sheet on one end. This lessens the force required to pull a tube. To eliminate tube cutting chips in the vessel, tubes should be scored and not totally cut through. The tube cutter needs to have sufficient reach to cut behind the tube sheet. Proper lubrication and cutting speed will increase cutting blade life.

*Tube Pullers- Used to break the seal and pull expanded tubes from a tube sheet. A spear or expanding collet is inserted and engaged into the tube inner diameter. A ram or gun applies force to exert an extracting force on the tube. The power to pull the tube is generated manually or through an hydraulic pump. The hydraulic pump can be manually, electrically or pneumatically driven. The pulling force required will vary with the tube size and wall, the depth of the tube sheet and tube material.

*Pneumatic Hammers-Pneumatic Hammers are an alternative method to remove tube stubs from heat exchangers and boilers. Maintenance technicians use piloted knockout tools to avoid damage to the tube sheet. The knockout tool is inserted into the tube and the impact pneumatic hammer is actuated to punch out the tube stub. Tube Installation (Tube Expanders)- Tube Expanding is the art of reducing a tube wall by compressing the outer diameter of the tube against a fixed container such as rolling tubes into tube sheets, drums, ferrules or flanges. Construction of heat exchangers, boilers, and surface condenser tubes is mainly limited to copper, steel, stainless steel, and cast iron with exceptions such as the use of titanium in ultra high pressure vessel applications. To assure a proper tube joint, the tube wall must be reduced by a predetermined percentage dependent upon the material the tube is constructed of. [url=http://www.elliott-tool.com/support/tools.asp] . For example,
*Tubing Material:
**Copper & Cupro Nickel 8 - 10%
**Steel, Carbon Steel & Admiralty Brass 7 - 8%
**Stainless Steel & Titanium 4 - 5%

Pneumatic or hydraulic torque rolling devices with an expander (consisting of a mandrel, cage with rolls, case assembly with a thrust collar) are used to expand the end of the tube so it seals against the tube sheet of the vessel. It is important to note that the type of tool has to be with paired not only with material but also the inner and outer dimensions of the tube as well. Thickness of the tube sheet (what each individual tube is inserted into) has to be taken into consideration during tube removal or installation procedures.

References

External links

cite web
title=Elliott Tool Technologies | url=http://www.elliott-tool.com

cite web
title=Heat Exchange Institute | url=http://www.heatexchange.org

cite web
title=International District Energy Association | url=http://www.districtenergy.org

cite web
title=American Society of Mechanical Engineers | url=http://www.asme.org

cite web
title=National Board of Boiler and Pressure Vessel Inspectors | url=http://www.nationalboard.org

cite web
title=The American Society of Heating, Refrigerating and Air-Conditioning Engineers | url=http://www.ashrae.org

cite web
title=National Petrochemical and Refiners Association | url=http://www.npra.org

cite web
title=International Aluminum Institute | url=http://www.world-aluminium.org

cite web
title=Tubular Exchanger Manufacturer Association | url=http://www.tema.org


Wikimedia Foundation. 2010.

Look at other dictionaries:

  • Tube — may refer to:Electronics *vacuum tube, a component of electronics *cathode ray tube, a common component of electronics such as televisions and other displays *Tube, An expansion bus on the BBC Micro computer *Nokia 5800 Tube , A mobile phoneFood… …   Wikipedia

  • Tube bending — Bent tubing Shown is a trombone, it displays some U bends Tub …   Wikipedia

  • Tool and die maker — Not to be confused with tap and die. Tool and die makers are workers in the manufacturing industry who make jigs, fixtures, dies, molds, machine tools, cutting tools (such as milling cutters and form tools), gauges, and other tools used in… …   Wikipedia

  • Tube lemma — In mathematics, particularly topology, the tube lemma is a useful tool in order to prove that the finite product of compact spaces is compact. It is in general, a concept of point set topology. Tube lemmaBefore giving the lemma, we note the… …   Wikipedia

  • tube cutter — A tool used to cut tubing by passing a sharp wheel around and around the tube. Also see mini tube cutter …   Dictionary of automotive terms

  • tube bender — A tool for bending tubing without collapsing it …   Dictionary of automotive terms

  • Elliott Tool Technologies — [ [http://www.elliott tool.com/elliott/about.asp Elliott Tool Technologies :: About Us ] ] was founded in September 1892 by an inventor and manufacturer named Gustav Wiedeke in his Dayton, Ohio home. He began designing and manufacturing… …   Wikipedia

  • measuring tube — tool used to measure liquids …   English contemporary dictionary

  • hand tool — any tool or implement designed for manual operation. * * * Introduction  any of the implements used by craftsmen in manual operations, such as chopping, chiseling, sawing, filing, or forging. Complementary tools, often needed as auxiliaries to… …   Universalium

  • Churchill Machine Tool Company — The Churchill Machine Tool Company Limited Type Machine Tool Manufacturer Industry Engineering Fate Taken over, liquidated …   Wikipedia


Share the article and excerpts

Direct link
Do a right-click on the link above
and select “Copy Link”

We are using cookies for the best presentation of our site. Continuing to use this site, you agree with this.