Cab signalling


Cab signalling

Cab signalling is a railroad safety system that communicates track status information to the train cab (driving position), where the engineer or driver can see the information. The simplest systems display the trackside signal aspect (typically, green, yellow or red, indicating whether it is safe to proceed or not), while more sophisticated systems also display allowable speed, location of nearby trains, and dynamic information about the track ahead. In modern systems, a "speed enforcement" system usually overlays on top of the cab signalling system to warn the driver of dangerous conditions, and to automatically apply the brakes and bring the train to a stop if the driver ignores the dangerous condition. ["Elements of Railway Signaling", General Railway Signal (June 1979)] These systems range from simple coded track circuits to transponders that communicate with the cab, to communication-based train control systems.

Introduction

The main purpose of a signal system is to enforce a safe separation between trains and to enforce speed limits. The cab signal system is an improvement over the wayside signal system, where visual signals beside or above the right-of-way govern the movement of trains, without any means of enforcing the signal automatically. While early cab signal systems only repeat the wayside signal aspect displayed, all modern systems have an enforcement component which can automatically bring a train to a stop.

The first such systems were installed on an experimental basis in the 1910s in the United Kingdom, 1920s in the United States, and later in the Netherlands in the 1940s. High-speed trains such as those in Japan, Northeastern United States, Britain, France, and Germany use such systems in principle, though they are mutually incompatible in practice.

The European Rail Traffic Management System (ERTMS) is a multi-national standard that is progressively being developed in Europe, with an aim to improve interoperability. The train-control component of ERTMS, termed European Train Control System (ETCS), is a functional specification that incorporates the former national standards of several European countries. The German Indusi, German LZB, British TPWS, and the French TVM could all be made ETCS-compliant with modifications.

In North America, the power-frequency coded track circuit system developed by the Pennsylvania Railroad and Union Switch & Signal (US&S) is the de-facto standard in the Northeast. Variations of this system is also in use on many rapid transit systems, including the MBTA Red Line, London Underground's Victoria Line, and forms the basis for the first generation Shinkansen signalling developed by Japan National Railways (JNR).

Hierarchy of cab signal systems

With a traditional signalling system, the engineer/operator must observe wayside signals and act accordingly, depending on the aspects displayed. This method of operation is susceptible to human failure; if the engineer does not respond to a signal aspect, a dangerous situation may result. It is also considered 'passive', in that the system does not actively prevent the unsafe conditions from arising. Cab signal is an active system, in that the train will default to a safe condition (brakes applied) if left unattended as it approaches an averse signal aspect. Thus, the reliance on humans to ensure absolute safety is somewhat reduced.

Intermittent, Continuous, and PTC

There are three classes of cab signal systems:

* Wayside signals with intermittent warning and enforcement capabilities
* Continuous cab signal and speed enforcement systems
* Positive Train Control (PTC) and other new technology systems

Typically, when the term 'cab signal system' is used, it refers to the continuous cab signal and speed enforcement system. However, the intermittent systems are also considered a form of cab signalling.

Intermittent

These systems provide for the transmission of information about approaching signal aspects to the train and some level of enforcement of those aspects. The most basic level of enforcement are the simple Automatic Train Stop (ATS) systems that apply the brakes if a train passes a stop signal. Such systems have been widely used on heavy rail transit systems since the earliest days. On main line railroads, initiating braking at a stop system would be ineffective because of higher speeds and lower braking rates. Instead a warning is transmitted to the train on passing an approach aspect requiring a speed reduction. If the warning is not acknowledged after a present time (usually 8 seconds), brakes are applied. If the warning is acknowledged a warning indication is displayed in the cab to the next clear signal, but the engineer is fully responsible for operating the train.

These systems have the obvious disadvantage that an engineer might acknowledge the warning but fail to take action to slow the train. To reduce this risk, newer types of ATS have been developed, such as PZB 90 in Germany and Train Protection & Warning System (TPWS) in the UK to enforce a speed reduction before the stop signal, and fully apply brakes if the signal is passed. The newest systems (such as ASES on New Jersey Transit commuter lines) use line side transponders to transmit complex messages to the passing train. Collision risk is reduced, but not completely eliminated. These systems are a compromise between intermittent and more costly systems with continuous track-train communications, that provide almost complete assurance against human error collisions.

Continuous

These systems (generally known as Automatic Train Control (ATC) systems) use the rails or loop conductors laid along the track to provide continuous communication between wayside signal systems and the train.cite web| title= NTIS order #PB-254738 - Automatic Train Control in Rail Rapid Transit| publisher=United States Congress Office of Technology Assessment| date=May 1976| url=http://www.princeton.edu/~ota/disk3/1976/7614/7614.PDF| format=PDF| ] The most widely used systems in the United States use coded track circuits to transmit and display the aspect of the approaching signal in the cab. An on-board speed enforcement system ensures that the speed for that signal aspect is observed when passing the signal. However, in their traditional form, the systems cannot enforce an absolute stop at a stop signal, since they do not have a way of determining precise train location and distance to the next signal. The more advanced ATC systems such as the LZB in Germany and the TVM series in France do have this capability. LZB and TVM systems are applied primarily on new high speed passenger lines. In the United States, the addition of the ACSES transponder-based speed enforcement systems provides the absolute stop, as well as enforcement of civil speed limits on portions of the Northeast Corridor.

PTC (Positive Train Control)

Positive Train Control is the term given in North America to a family of train control technologies that aims to provide the functionality of the most advanced ATC systems described in the previous section, plus some additional functions, at a much lower cost.

PTC systems typically rely on wireless data communications between the control center and trains to minimize costly wayside installations. Such systems are known as Communications Based Train Control (CBTC). CBTC comprises a variety of systems used in lieu of traditional block signals and interlockings for managing safety and capacity, especially non-traditional ways of determining exact train location, for example using GPS and inertial navigation, and digital radio for communications between trains, wayside devices (such as switches and grade crossings) and zone controllers and the control center.

These systems are increasingly common on urban heavy rail rapid transit systems (such as the pilot CBTC installation on the Canarsie Line of the NYCT), and are being widely tested in main line applications. Most of these systems are not fully mature, and are still in development or service trials.

Information transmittal

Cab signals require a means of transmitting information from wayside to train. There are a few main methods to accomplish this information transfer:

* Mechanical
* Magnetic field
* Electric current
* Inductive (changing magnetic field)
* Coded track circuits

Mechanical

The most basic type of cab signal system is one that relies on mechanical contact between wayside equipment and the train. The New York City Transit Authority (NYCT), and the London Underground uses this system to this date on some of its lines. This is known as the 'trip-stop' system (also called Train stop). If a stop signal is displayed, a trip-arm located next to the running rails becomes 'raised'. On the bogies/trucks of the underground/subway cars, there is an emergency brake valve. If a train would overrun a stop signal, the raised arm would strike the emergency brake valve, causing the train's compressed air line to depressurize or be 'dumped'. [cite web| title=Subway Signals: A Complete Guide| url=http://www.nycsubway.org/tech/signals/| ] The brakes throughout the entire train is automatically applied.

This form of Automatic Train Stop (ATS) is considered a cab signal system, albeit a rudimentary one. It provides exactly two aspects, "stop" and "go". It does nothing to regulate speeds, does not display the signal aspect inside the cab, and does not enforce a signal aspect until a stop signal overrun actually occurs. However, it is much safer than not having a cab signal system at all.

Magnetic field

A variation of the mechanical contact system is to use the absence of a magnetic field to designate a hazardous condition. [Railway Signalling -- A guide to modern signalling technology, Institution of Railway Signal Engineers. Published 1980.] The British Rail AWS (Automatic Warning System) is an example of an automatic train stop system transmitting information using a magnetic field.

This form of automatic warning system is also a two-aspect cab signal system. It does not provide absolute stop enforcement although its systemwide installation has prevented many accidents on Britain's railways. Because of a series of high profile SPAD (Signal passed at danger) incidents, from around 1999 AWS was supplemented by the Train Protection & Warning System (TPWS), which provides stop signal enforcement.

Electric current

The magnetic systems are non-contact and are generally preferred -- contact between a fast moving train and wayside equipment leads to a lot of wear and tear. However, in the early part of the 20th Century, the Great Western Railway in Great Britain experimented with an electric system, whereby long bars in the 'four-foot' between the rails became energized with an electric current (supplied from a battery) when the distant signal was clear. This system is described in the article on Automatic Warning System.

Inductive

Inductive system are non-contact systems that rely on more than the simple presence or absence of a magnetic field to transmit a message. Inductive systems typically require a beacon or an inductive loop to be installed at every signal and other intermediate locations. The inductive coil uses a changing magnetic field to transmit messages to the train. Typically, the frequency of pulses in the inductive coil are assigned different meanings.

Examples of inductive systems include the German Indusi system, and the British TPWS.

Coded track circuits

A coded track circuit based system is essentially an inductive system that uses the running rails as information transmitter. The coded track circuits serve a dual purpose: to perform the train detection and rail continuity detection functions of a standard track circuit, and to continuously transmit signal indications to the train. In so doing, the coded track circuit systems also eliminate the needs for specialized beacons.

Examples of coded track circuit systems include the Pennsylvania Railroad standard system described below, a variation thereof used on the London Underground's Victoria Line, [cite web| work=Tubeprune| title=Automatic Train Operation on the Victoria Line| url=http://www.trainweb.org/tubeprune/Victoria%20Line%20ATO.htm| date=2003-03-15| accessdate=2008-03-13| ] and one used on the MBTA Red Line. Newer audio frequency (AF) track circuit systems are used on the Hudson-Bergen Light Rail (HBLR) and Newark Light Rail. The AF track circuits differ from traditional power-frequency coded track circuits in that it relies more heavily on digital signal processing to transmit and detect information but can be cheaper and simpler to design and implement.

Typology of cab signal systems

Cab signal systems in the US

Cab signaling in the United States was driven by a 1922 ruling by the Interstate Commerce Commission that required 49 railroads to install some form of automatic train control in one full passenger division by 1925. [citation
title = Railroad Operational Safety, Status and Research Needs
edition= Transportation Research Circular E-C085
date = January 2006
publisher = Transportation Research Board of the National Academies
url = http://www.trb.org/publications/circulars/ec085.pdf
page = 27
accessdate = 2008-04-13
] Now while several large railroads including the Santa Fe and New York Central decided to fulfill the letter of the requirement by installing intermittent inductive train stop devices, the Pennsylvania Railroad saw an opportunity to improve operational efficiency and installed the first continuous cab signal systems.

In response to the Pennsylvania Railroad lead, the ICC mandated that some of the nation's other large railroads had to equip at least one division with continuous cab signal technology as a test to compare technologies and operating practices. The affected railroads were somewhat less than enthusiastic and many chose to equip one of their more isolated or less trafficked routes to minimize the number of locomotives needing to be equipped with the cab signal apparatus.

Several railroads chose the inductive loop system rejected by the PRR. These included the Central Railroad of New Jersey (installed on its Southern Division), the Reading Railroad (installed on its Atlantic City main line) and the New York Central. Both the Chicago Northwestern and Illinois Central employed a two-aspect system on select suburban lines near Chicago. The cab signals would display "Clear" or "Restricting". The CNW went even further and also eliminated the wayside intermediate signals in the stretch of track between Elmhurst and West Chicago, requiring trains to proceed solely based on the 2 aspect cab signals.

As the Pennsylvania Railroad system was the only one adopted on a large scale, it eventually wound up becoming a de facto national standard and most installations of cab signals in the current era have been of this type. Recently there have been several new types of cab signaling which seek either to use communications based technology to reduce the cost of wayside equipment or supplement existing signal technologies to enforce speed restrictions, absolute stops and respond to grade crossing malfunctions or incursions.

The first of these was the Speed Enforcement System employed by New Jersey Transit on their low density Pascack Valley Line as a pilot program using a dedicated fleet of 13 GP40PH-2. SES used a system of transponder beacons attached to wayside block signals to enforce signal speed. SES was near universally disliked by engine crews due to its habit of causing immediate penalty brake applications without first sounding an overspeed alarm and giving the engineer a chance to slow down. SES is in the process of being removed from this line, and is being replaced with CSS.

Amtrak decided to adopt the Advanced Civil Speed Enforcement System or ACSES for its new high speed rail service to Boston. ACSES was an overlay to the existing PRR type CSS and used the same SES transponder technology to enforce permanent and temporary speed restrictions at curves and other geographic features on the line. The on board cab signal unit would process both the pulse code "signal speed" and the ACSES "civil speed" and then enforce the lower of the two. ACSES also provided for a positive stop at absolute signals which could be released by a code provided by the dispatcher transmitted from the stopped locomotive via a data radio. Later this was amended to a more simple "stop release" button on the cab signal display. ACSES is slowly being implemented along the Northeast Corridor between Boston and Washington, but in most cases it only is used by the high speed transits.

Pennsylvania Railroad Pulse Code Cab Signal System

The first widely implemented railroad cab signaling system was employed by the Pennsylvania Railroad in the 1920s and continues to be the dominant cab signal system in North America. The Interstate Commerce Commission ruled in 1922 that trains would be limited to 80mph without some sort of automatic train stop system and the Pennsylvania Railroad decided to address this ruling with a technology that could improve both safety and operational efficiency. This came in the form of a signal displaying continuously in the cab of the locomotive based on electrical current transmitted through the rails. The technology was developed by the Union Switch and Signal corporation, the PRR's preferred signal supplier.

The first test installation between Sunbury, PA and Lewistown, PA consisted of turning the tracks into an inductive loop with three aspects (RESTRICTING, APPROACH and CLEAR) and signals transmitted using commercial 60Hz current. The test installation also did away with wayside block signals with trains relying solely on cab signals. The PRR installed another "loop" system on the Northern Central line between Baltimore, MD and Harrisburg, PA in 1926, this time using special 100Hz current.

In 1927 the PRR began to test another variation of Cab Signals which used pulse codes instead of inductive loops. The pulses of 100Hz current were detected via induction by a sensor hanging a few inches above the rail before the leading set of wheels. The codes were 180 ppm for CLEAR, 120ppm for APPROACH MEDIUM, 75ppm for APPROACH and 0 for RESTRICTING. The pulse rates were chosen to avoid any one rate being a multiple of another leading to reflected harmonics causing false indications. [ [http://www.freepatentsonline.com/4437056.html Cab signal test set for automatically testing the pickup coils and checking an amplifier of cab signal equipment - Patent 4437056 ] ] The system was failsafe in that the lack of code would display a RESTRICTING signal. The codes would be transmitted to the train from the block limit in front of it. This way if the rail was broken or another train entered the block, any codes would not reach the onrushing train and the cab signal would again display RESTRICTING.

Initially the cab signaling system only acted as a form of automatic train stop where the engineer would have to respond to any drop in the cab signal to a more restrictive aspect to prevent the brakes from automatically applying. Later, passenger engines were upgraded with speed control which enforced the rulebook speed associated with each cab signal (APPROACH MEDIUM = 45mph, APPROACH = 30mph, RESTRICTING = 20mph).

Over time the PRR installed cab signals over much of its eastern system from Pittsburgh to Philadelphia, New York to Washington. Where DC and AC electrification co-exist the standard 100Hz frequency is changed to 91 2/3Hz to avoid even harmonics created by the 25Hz traction current flowing through DC motors. [EDWIN L. HARDER An Interview Conducted by William Aspray IEEE History Center 30-31 July 1991 Interview # 118 For the IEEE History Center The Institute of Electrical and Electronics Engineers, Inc. and Rutgers, The State University of New Jersey]

This system was then inherited by Conrail and Amtrak and various commuter agencies running on former PRR territory such as SEPTA and New Jersey Transit. Because all trains running in cab signal territory had to be equipped with cab signals, most locomotives of the aforementioned roads were fitted with cab signal equipment. Due to the effect of interoperability lock in, the 4-aspect PRR cab signal system has become a de-facto standard and almost all new cab signaling installations have been of this type or a compatible type.

Current lines using the 4-aspect PRR Cab Signal System

* Amtrak Northeast Corridor Line
* Amtrak Harrisburg Line
* Amtrak Springfield Line
* Amtrak Michigan Line
* Amtrak Shore Line (no waysides New Haven to Providence)
* Norfolk Southern Pittsburgh Line
* Norfolk Southern Port Road Line
* Norfolk Southern Conemaugh Line (no waysides)
* Norfolk Southern Morrisville Line (no waysides)
* Norfolk Southern Fort Wayne Line (Conway Yard to Alliance, OH, no waysides)
* Norfolk Southern Cleveland Line (Alliance, OH to Cleveland, OH, no waysides)
* CSX Boston Line (no waysides)
* CSX Hudson Line
* CSX Landover Line
* CSX RF&P Sub (formerly using RF&P CSS system at 60 Hz)
* NJT All Lines
* Metro-North All "East of Hudson" Lines (no waysides)
* MBTA Old Colony Lines (no waysides)
* SEPTA Main Line
* SEPTA Airport Line
* SEPTA Chestnut Hill West Line
* SEPTA Neshamity Line
* SEPTA Fox Chase Line

Related Pulse Code Systems

;
*Long Island Rail Road Automatic Speed Control: The LIRR was a PRR subsidiary and it is no surprise that they would adopt a similar system. The LIRR used standard PRR cab signals until bought by the Metropolitan Transportation Authority in 1968 when it was modified slightly into ACS systems used to this day. ASC employs two additional codes, 270 and 420 ppm and replaces the in-cab signal display with an in-cab speed display. Th additional codes are used to display speeds of 50/60 and 60/70 mph, which are used to slow trains for curves, higher speed turnouts and short signal blocks.

*Chicago, Burlington and Quincy Aurora Line Cab Signals: The CB&Q commuter line to Aurora, Illinois used the same technology as the Pennsylvania, just with different rules and wayside indications to conform to their partly route-based signaling system. It remains in service to the present day.

*Union Pacific Automatic Train Control: The Union Pacific has implemented the PRR type technology on much of its main line between Chicago and Wyoming, as well as several other lines on its system in recent years. As with the CB&Q cab signals, the system works the same as the PRR, but uses different rules and partly route based wayside signals.

*METRA Rock Island Automatic Train Control: Another PRR based cab signal system left over from the Rock Island heyday. It can be found on the Joliet IL to Chicago portion of Metra, the Metra Rock Island District

*Rapid Transit Lines: Various rapid transit lines built or re-signaled in or before the 1990s make use of the pulse-code cab signal technology for both manual or automatic train operation schemes. Rapid transit systems are typically failsafe with a O code mandating a complete stop of the rail vehicle. Also, the complete range of pulse codes are used to provide the maximum granularity in speed control. Some examples include the PATCO Speedline in Philadelphia, the SEPTA Route 100, the Baltimore Metro and the Miami-Dade Metrorail. Pulse-code technology on rapid transit lines has generally been supplanted by Audio-Frequency cab signals.

*MTA Staten Island Railway Automatic Speed Control: A hybrid of the PRR/LIRR systems and Rapid Transit power-frequency cab code. The ATC applies service braking in response to overspeed conditions. 75-120-180-270 are used as speed commands. Zero code is used for stop rather than restricting, which is 50PPM. 420 is used as a latch-out. Dispatchers may authorize trains stopped by a zero-code to close in on certain interlocking signals by manually activating a 50PPM close-in code.

Positive Train Control

Positive Train Control systems can be overlaid onto cab signal systems or can replace them altogether. These include the Incremental Train Control System (ITCS) installed by GE on the Chicago-Detroit route in Michigan and the North American Joint Positive Train Control (NAJPTC) system being testing in Illinois on the Chicago-St. Louis route. The ITCS has been in revenue service since 2002 with speeds up to 90 mph (145 km/h). [cite web| url=http://www.fra.dot.gov/us/content/1265| title=Positive Train Control Overview| author=United States Federal Railroad Administration| date=2004-12-15| accessdate=2007-01-10| ] Other systems include Alaska Railroad's CAS, CSX's CBTM, and BNSF's ETMS. [ [http://s3.amazonaws.com/trainmedia/video/etms.mpg BNSF promotional video] .]

Audio frequency track circuits

While pulse-coded track circuit have on/off cycles measured in pulses per minute, as its name implies, audio-frequency track circuit have signal frequencies in the range between 2000 Hz and 20000 Hz. Because of the relatively high frequency the signal quickly attenuates and while pulse codes can travel for several miles, audio frequency codes can only travel between a few hundred and a few thousand feet. However, this has an advantage in that by carefully matching the carrier frequency to the block length, the need for insulated rail joints can be largely eliminated. In rapid transit and light rail systems, where high traffic density mandates short signal blocks, the lack of a need for insulated rail joints (and impedance bonds) can result in significant cost savings.

Like standard track circuits, the audio frequency track-circuits provide positive train detection and like pulse code cab signals they provide the transmission of signal aspects which can change between block boundaries. Also like the pulse code system the vehicle borne equipment reads the code embedded in the audio frequency carrier and then passes this on to the train control system to alert the operator and/or reduce train speed as necessary.

References

External links

* [http://www.svmetro.com/septawatch/signals/cab-signal-system.php Schuylkill Valley Metro cab signal system]


Wikimedia Foundation. 2010.

Look at other dictionaries:

  • Signalling block system — Signalling block systems enable the safe and efficient operation of railways, so as to avoid collisions between trains. Block systems are used to control trains between stations and yards, and not normally within them. Any block system is defined …   Wikipedia

  • Cab Secure Radio — (CSR) is an in cab analogue radiotelephone system used on parts of the British railway network. Its main function is to provide a secure speech link between the train driver and the signaller which cannot be overheard by other train drivers. In… …   Wikipedia

  • cab — taxicab ax i*cab, n. an automobile with a professional driver which can be hired to carry passengers; also called a {taxi}, and informally called a {cab} or a {hack}. The driver of a taxicab is referred to as a {cab driver} or {cabbie}, and… …   The Collaborative International Dictionary of English

  • Railway signalling — Not to be confused with Railway signal. A gantry of British semaphore signals seen from the cab of a steam locomotive Railway signalling is a system used to control railway traffic safely, essentially to prevent trains from colliding. Being… …   Wikipedia

  • Token (railway signalling) — A token being offered by a signalman on the Keighley and Worth Valley Railway …   Wikipedia

  • Dutch railway signalling — The current Dutch railway signalling system operated by ProRail has been in effect since 1954 on the Dutch Railways network It was designed to be one of the simplest in Europe and is integrated to the ATB, the system of cab signalling widespread… …   Wikipedia

  • Norwegian railway signalling — The signalling system used on the rail transport in Norway is regulated by the Regulations of December 4, 2001 no. 1336 about signals and signs on the state s railway network and connected private tracks. The first signalling system on the… …   Wikipedia

  • UK railway signalling — The railway signalling systems used across the majority of the United Kingdom rail network use lineside signals to advise the driver of the status of the section of track ahead. Most lineside signals are in colour light form, but a significant… …   Wikipedia

  • to flag down a cab — taxicab ax i*cab, n. an automobile with a professional driver which can be hired to carry passengers; also called a {taxi}, and informally called a {cab} or a {hack}. The driver of a taxicab is referred to as a {cab driver} or {cabbie}, and… …   The Collaborative International Dictionary of English

  • to hail a cab — taxicab ax i*cab, n. an automobile with a professional driver which can be hired to carry passengers; also called a {taxi}, and informally called a {cab} or a {hack}. The driver of a taxicab is referred to as a {cab driver} or {cabbie}, and… …   The Collaborative International Dictionary of English


Share the article and excerpts

Direct link
Do a right-click on the link above
and select “Copy Link”

We are using cookies for the best presentation of our site. Continuing to use this site, you agree with this.