Well kill

Well kill

A well kill refers to the operation of placing a column of heavy fluid into a well bore in order to prevent the flow of reservoir fluids without the need for pressure control equipment at the surface. It works on the principle that the weight of the "kill fluid" or "kill mud" will be enough to suppress the pressure of the formation fluids. Well kills may be planned in the case of advanced interventions such as workovers, or be contingency operations. The situation calling for a well kill will dictate the method taken.

Not all well kills are deliberate. Sometimes, the unintended build up of fluids, either from injection of chemicals like methanol from surface, or from liquids produced from the reservoir, can be enough to kill the well, particularly gas wells, which are notoriously easy to kill.

Principles

The principle of a well kill revolves around the weight of a column of fluid and hence the pressure exerted at the bottom.

P=hg ho

Where P is the pressure at depth h in the column, g is the acceleration of gravity and ρ is the density of the fluid. It is common in the oil industry to use weight density, which is the product of mass density and the acceleration of gravity. This reduces the equation to:

P=hgamma

Where γ is the weight density. Weight density may also be described as the pressure gradient because it directly determines how much extra pressure will be added by increasing depth of the column of fluid.

The objective in a well kill, is to make the pressure at the bottom of the kill fluid equal (or slightly greater) than the pressure of the reservoir fluids.

Example

The pressure of the reservoir fluids at the bottom of the hole is 38MPa. We have a kill fluid with a weight density of 16kN.m-3. What will need to be the height of the hydrostatic head in order to kill the well?

From the equation:h=frac{P}{gamma}

h=frac{38MPa}{16kNm^{-3

h=2375m

Therefore, a column of 2375m of this fluid is needed. It must be remembered that this refers to the true vertical depth of the column, not the measured depth, which is always larger than true vertical depth due to deviations from vertical.

Maths in the oil field

In the oil industry, a pure SI system is far from being used. Weight densities are commonly either given as specific gravity or in pounds per gallon. Simple conversion factors (0.433 for specific gravity and 0.052 for ppg) convert these values to a pressure gradient in psi per foot. Multiplying by the depth in feet gives the pressure at the bottom of the column.

Methods of well kill

Reverse circulation

This is often tidiest way of making a pre-planned well kill. It involves pumping kill fluid down the 'A' annulus of the well, through a point of communication between it and the production tubing just above the production packer and up the tubing, displacing the lighter well bore fluids, which are allowed to flow to production.

The point of communication was traditionally a device called a sliding sleeve, or sliding side door, which is a hydraulically operated device, built into the production tubing. During normal operation, it would remain closed sealing off the tubing and the annulus, but for events such as this, it would be opened to allow the free flow of fluids between the two regions. These components have fallen out of favour as they were prone to leaking. Instead, it is now more common to punch a hole in the tubing for circulation kills. Although this permanently damages the tubing, given that most pre-planned well kills are for workovers, this is not an issue, since the tubing is being pulled for replacement anyway.

Bullheading

This is the most common method of a contingency well kill. If there is a sudden need to kill a well quickly, without the time for rigging up for circulation, the more blunt instrument of bullheading may be used. This involves simply pumping the kill fluid directly down the well bore, forcing the well bore fluids back into the reservoir. This can be effective at achieving the central aim of a well kill; building up a sufficient hydrostatic head in the well bore. However, it can risk damaging the reservoir, by forcing undesired materials into it. The principal advantage is that it can be done with little advanced planning.

Forward circulation

This is similar to reverse circulation, except the kill mud is pumped into the production tubing and circulated out through the annulus. Though effective, it is not as desirable since it is preferred that the well bore fluids be displaced out to production, rather than the annulus.

Lubricate and bleed

This is the most time consuming form of well kill. It involves repeatedly pumping in small quantities of kill mud into the well bore and then bleeding off excess pressure. It works on the principle that the heavier kill mud will sink below the lighter well bore fluids and so bleeding off the pressure will remove the latter leaving an increasing quantity of kill mud in the well bore with successive steps.

Well kills during drilling operations

During drilling, pressure control is maintained through the use of precisely concocted drilling fluid, which balances out the pressure at the bottom of the hole. In the event of suddenly encountering a high pressure pocket of, say gas (called a "kick"), it can become necessary to kill the well. This is done by pumping kill mud down the drill pipe, where it circulates out the bottom and into the well bore.

Reversing a well kill

The intention of a well kill (or the reality of an unintentional well kill) is to stop reservoir fluids flowing to surface. This of course creates problems when it is desirable to get the well flowing again. In order to reverse the well kill, the kill fluid must be displaced from the well bore. This involves injecting a gas at high pressure, usually nitrogen since it is inert and cheap. A gas can be put under sufficient pressure to allow it to push heavy kill fluid, but will then expand and become light once pressure is removed. This means that having displaced the kill fluid, it will not itself kill the well. The reservoir fluids should be able to flow to surface, displacing the gas.

The cheapest way to do it is similar to bullheading, where the nitrogen is pumped in under high pressure to force the kill fluid into the reservoir. This, of course, runs a high risk of causing well damage. The most effective way is to use coiled tubing, pumping the gas down the coil and circulating out the bottom into the well bore, where it will displace the kill mud to production.

ee also

*Oil well
*Well intervention
*Well drilling
*Coiled tubing

External links

* [http://www.iwcf.org/IWCF/Public/PDF/QA-WIS%20WI%20Syllabus,%20Rev%203.2,%201-08-2004,%20B&W.pdf IWCF Well Intervention Pressure Control syllabus (pdf)]


Wikimedia Foundation. 2010.

Игры ⚽ Нужно решить контрольную?

Look at other dictionaries:

  • Well stimulation — is a well intervention performed on an oil or gas well to increase production by improving the flow of hydrocarbons from the drainage area into the well bore.Cleaning the formationThe assortment of chemicals pumped down the well during drilling… …   Wikipedia

  • Kill Switch...Klick — promo shot from 1993 (L to R, D.A. Sebasstian, Victoria Knight Mike Ditmore). Background information Ori …   Wikipedia

  • Kill Bill Volume 1 — Teaser poster Directed by Quentin Tarantino Produced by …   Wikipedia

  • Kïll Cheerleadër — Kill Cheerleader Origin Toronto, Ontario Canada Genres Hard rock, Punk, Heavy metal, Rock n Roll Years active 1999–2006 Labels …   Wikipedia

  • Kill ’Em All — Studioalbum von Metallica Veröffentlichung 25. Juli 1983[1][2] …   Deutsch Wikipedia

  • Kill Buddha — were an American alternative rock band from Los Angeles, California, active in 1992 – 1995. Kill Buddha toured around Southern California mainly playing in West Hollywood, Hollywood and Santa Monica clubs like The Roxy, Raji s, and Alligator… …   Wikipedia

  • Kill the Indian, Save the Man — Kill the Indian, Save the Man: The Genocidal Impact of American Indian Residential Schools is a 2004 book by Ward Churchill. It traces the history of removing Native American children from their homes to residential schools (in Canada) or Indian… …   Wikipedia

  • Well Bargained and Done — is the second episode of .PlotOn the desert planet named DustballAdam, Hawkins and Specter walk the streets of a domed city, looking for any halfway decent mechwarriors they can find to join the Strikers (because, as Adam reminds Hawkins, all the …   Wikipedia

  • Kill 'Em All — For other uses, see Kill Em All (disambiguation). Kill Em All Studio album by Metallica …   Wikipedia

  • Kill, County Kildare — Infobox Irish Place name = Kill gaeilge = An Chill crest motto = map pin coords = left: 72px; top: 45px north coord = 53.3 | west coord = 6.5 | irish grid = area = | elevation = 61 m province = Leinster county = County Kildare population = | town …   Wikipedia

Share the article and excerpts

Direct link
Do a right-click on the link above
and select “Copy Link”