Double wishbone suspension

Double wishbone suspension
Wishbones and upright painted yellow

In automobiles, a double wishbone (or upper and lower A-arm) suspension is an independent suspension design using two (occasionally parallel) wishbone-shaped arms to locate the wheel. Each wishbone or arm has two mounting points to the chassis and one joint at the knuckle. The shock absorber and coil spring mount to the wishbones to control vertical movement. Double wishbone designs allow the engineer to carefully control the motion of the wheel throughout suspension travel, controlling such parameters as camber angle, caster angle, toe pattern, roll center height, scrub radius, scuff and more.

Contents

Implementation

Double Wishbone Suspension

The double-wishbone suspension can also be referred to as "double A-arms," though the arms themselves can be of a A-shaped, L-shaped, or even a single bar linkage. A single wishbone or A-arm can also be used in various other suspension types, such as MacPherson strut and Chapman strut. The upper arm is usually shorter to induce negative camber as the suspension jounces (rises), and often this arrangement is titled an "SLA" or "short long arms" suspension. When the vehicle is in a turn, body roll results in positive camber gain on the lightly loaded inside wheel, while the heavily loaded outer wheel gains negative camber.

Between the outboard end of the arms is a knuckle with a spindle (the kingpin), hub, or upright which carries the wheel bearing and wheel.

In order to resist fore-aft loads such as acceleration and braking, the arms require two bushings or ball joints at the body.

At the knuckle end, single ball joints are typically used, in which case the steering loads have to be taken via a steering arm, and the wishbones look A- or L-shaped. An L-shaped arm is generally preferred on passenger vehicles because it allows a better compromise of handling and comfort to be tuned in. The bushing inline with the wheel can be kept relatively stiff to effectively handle cornering loads while the off-line joint can be softer to allow the wheel to recess under fore aft impact loads. For a rear suspension, a pair of joints can be used at both ends of the arm, making them more H-shaped in plan view. Alternatively, a fixed-length driveshaft can perform the function of a wishbone as long as the shape of the other wishbone provides control of the upright. This arrangement has been successfully used in the Jaguar IRS. In elevation view, the suspension is a 4-bar link, and it is easy to work out the camber gain (see camber angle) and other parameters for a given set of bushing or ball joint locations. The various bushings or ball joints do not have to be on horizontal axes, parallel to the vehicle centre line. If they are set at an angle, then antidive and antisquat geometry can be dialed in.

In many racing cars, the springs and dampers are relocated inside the bodywork. The suspension uses a bellcrank to transfer the forces at the knuckle end of the suspension to the internal spring and damper. This is then known as a "push rod" if bump travel "pushes" on the rod (and subsequently the rod must be joined to the bottom of the upright and angled upward). As the wheel rises the push rod, via a pivot or pivoting system, compresses the internal spring. The opposite arrangement, a "pull rod," will pull on the rod during bump travel, and the rod must be attached to the top of the upright, angled downward. Locating the spring and damper inboard increases the total mass of the suspension, but reduces the unsprung mass, and also allows the designer to make the suspension more aerodynamic.[1]

Advantages and disadvantages

The advantage of a double wishbone suspension is that it is fairly easy to work out the effect of moving each joint, so the kinematics of the suspension can be tuned easily and wheel motion can be optimized. It is also easy to work out the loads that different parts will be subjected to which allows more optimized lightweight parts to be designed. They also provide increasing negative camber gain all the way to full jounce travel unlike the MacPherson strut which provides negative camber gain only at the beginning of jounce travel and then reverses into positive camber gain at high jounce amounts.

The disadvantage is that it is slightly more complex than other systems like a MacPherson strut. Due to the increased number of components within the suspension setup it takes much longer to service and is heavier than an equivalent MacPherson design.

Uses

The double wishbone suspension was introduced in 1935 by Packard Motor Car Company of Detroit, Michigan on the Packard One-Twenty[citation needed], and advertised as a safety feature. Prior to the dominance of front wheel drive in the 1980s, many everyday cars used double wishbone front-suspension systems, or a variation on it. Since that time, the MacPherson strut has become almost ubiquitous, as it is simpler and cheaper to manufacture. In most cases, a MacPherson strut requires less space to engineer into a chassis design, and in front-wheel-drive layouts, can allow for more room in the engine bay. A good example of this is observed in the Honda Civic, which changed its front-suspension design from a double wishbone design to a MacPherson strut design after the year 2000 model.

Double wishbones are usually considered to have superior dynamic characteristics as well as load-handling capabilities, and are still found on higher performance vehicles. Examples of makes in which double wishbones can be found include Alfa Romeo, Honda and Mercedes-Benz. Short long arms suspension, a type of double wishbone suspension, is very common on front suspensions for medium-to-large cars such as the Honda Accord, Peugeot 407, or Mazda 6/Atenza, and is very common on sports cars and racing cars.

See also

External links

References


Wikimedia Foundation. 2010.

Игры ⚽ Нужно сделать НИР?

Look at other dictionaries:

  • double wishbone suspension — See double wishbone …   Dictionary of automotive terms

  • wishbone suspension — See double wishbone suspension unequal length wishbone suspension …   Dictionary of automotive terms

  • unequal-length wishbone suspension — A double wishbone suspension system in which the upper wishbone is shorter than the lower one, with both converging slightly at the wheel hub; reduces tire wear due to variations in track and camber angle when cornering …   Dictionary of automotive terms

  • double wishbone — A form of independent suspension used on the front of a vehicle where both the upper and lower wishbones are of equal length …   Dictionary of automotive terms

  • Wishbone — may refer to: * The wishbone, known in anatomy as the furcula, is a fused clavicle bone found in birds which is shaped like the letter Y. * The same clavicle bone as a lucky charm. * Wishbone (TV series), an educational children s television show …   Wikipedia

  • suspension — [1] The assembly of springs, shock absorbers, torsion bars, joints, arms, etc., that cushions the shock of bumps on the road and serves to keep the wheels in constant contact with the road, thereby improving control and traction. [2] A mixture of …   Dictionary of automotive terms

  • Suspension (vehicle) — Suspension is the term given to the system of springs, shock absorbers and linkages that connects a vehicle to its wheels. Suspension systems serve a dual purpose – contributing to the car s handling and braking for good active safety and driving …   Wikipedia

  • Multi-link suspension — Multi link rear suspension of the 5 link type rear view …   Wikipedia

  • Automotive suspension design — is an aspect of automotive engineering, concerned with designing the suspension for cars and trucks.The process entails *selecting appropriate vehicle level targets *selecting a system architecture *choosing the location of the hard points , or… …   Wikipedia

  • Short long arms suspension — An SLA is also known as an unequal length double wishbone suspension. The upper arm is typically an A arm, and is shorter than the lower link, which is an A arm or an L arm, or sometimes a pair of tension/compression arms. In the latter case the… …   Wikipedia

Share the article and excerpts

Direct link
Do a right-click on the link above
and select “Copy Link”