- Lath and plaster
Lath and plaster is a building process used mainly for
interior walls in Canadaand the United Statesuntil the late 1950s. After the 1950s, drywallbegan to replace the lath and plaster process in the these countries. In the United Kingdom, lath and plaster was used for some interior partition walls, but was mostly used in the construction of ceilings. In the UK, plasterboardbecame a more common ceiling construction from 1945 onwards.
The process begins with wood
laths. These are narrow strips of woodnailed horizontally across the wall studs. Each wall frame is covered in lath, tacked at the studs. The lath is typically about two inches wide by four feet long by 1/4 inch thick. Each horizontal course of lath is spaced about 1/4 inch away from its neighboring courses. Next, temporary lath guides are sparsely vertically to the wall, usually vertically at the studs. Plasteris then applied, typically using a wooden board as the application tool. The applier drags the board upward over the wall, forcing the plaster into the gaps between the lath and leaving a layer on the front the depth of the temporary guides, typically about 1/4 inch. A helper feeds new plaster onto the board, as the plaster is applied in quantity. When the wall is fully covered, the vertical lath "guides" are removed, and their "slots" are filled in, leaving a fairly uniform undercoat.
It is standard to apply a second layer in the same fashion, leaving about a half inch of rough, sandy plaster (called a brown coat). A smooth, white finish coat goes on last. After the plaster is completely dry, the walls are ready to be painted. In the photo, "lath seen from the back..." those curls of plaster are called "keys" and are important to keep the plaster on the lath. Insufficient "keying" and the plaster will fall off the lath. In the past,
horsehairwas used to help bind the plaster to the laths.
Eventually the wood laths were replaced with rock lath, which is a type of
gypsumwall board available in sheets size 2 by 4 feet. The purpose of the four-foot length is so that the sheet of lath reaches exactly across three wall studs, which are spaced 16 inches apart on center (American building codestandard measurements).
In addition to rock lath, there were various types of diamond mesh metal lath which is categorized according to weight, type of ribbing, and whether the lath is
galvanized or not. Metal lathing was spaced across a 13.5 inch center, attached by tie wires using lathers' nippers. Sometimes, the mesh was dimpled to be self- furring.
Lath and plaster has been replaced altogether with
drywallor plasterboard(also a type of gypsum wall board, although a bit thicker), since it can be installed without application of plaster to finish the surface. As plastering is a skilled trade, and hence expensive, reducing the amount of plastering required in a new development also reduces the building costs.
An advantage of using lath is for ornamental or unusual shapes. For instance, building a rounded wall would be difficult if drywall was used exclusively, and drywall is not flexible enough to allow tight radii.
* [http://www.cr.nps.gov/hps/tps/briefs/brief21.htm Preservation Brief No. 21] by the National Park Service. Contains detailed descriptions of Lath & Plaster construction and advisories on repairing and restoring these walls (especially in historic buildings).
Wikimedia Foundation. 2010.
Look at other dictionaries:
lath and plaster — noun a building material consisting of thin strips of wood that provide a foundation for a coat of plaster • Hypernyms: ↑building material … Useful english dictionary
Plaster veneer — is a construction methodology for surfacing interior walls, by applying a thin layer of plaster over a substrate typically over specially formulated drywall.History ). Later, drywall became a standard. Typically, drywall is surfaced using the mud … Wikipedia
Lath — A lath is a thin, narrow strip of some straight grained wood or other material, including metal or gypsum. A lattice, or lattice work, is a criss crossed or interlaced arrangement of laths, or the pattern made by such an arrangement. Lath is the… … Wikipedia
Plaster — The term plaster can refer to plaster of Paris, lime plaster, or cement plaster. This article deals mainly with plaster of Paris.Plaster of Paris is a type of building material based on calcium sulfate hemihydrate, nominally CaSO4·0.5H2O. It is… … Wikipedia
lath — n. & v. n. (pl. laths) a thin flat strip of wood, esp. each of a series forming a framework or support for plaster etc. v.tr. attach laths to (a wall or ceiling). Phrases and idioms: lath and plaster a common material for interior walls and… … Useful english dictionary
plaster — Synonyms and related words: Ace bandage, Band Aid, Portland cement, Spackle, adherent, adhesive, adhesive tape, adobe, application, ashlar, band, bandage, bandaging, barnacle, bathe, bedaub, besmear, binder, booze up, boozify, brace, bramble,… … Moby Thesaurus
plaster — I (New American Roget s College Thesaurus) n. plaster of paris, mortar, parget, stucco, gesso; paste, lime; clay, adobe, mud; poultice, dressing, bandage. See materials, connection, remedy. v. t. coat, cover, conceal, smear; caulk, repair, mend;… … English dictionary for students
Lath Art — is a form of woodworking Folk Art for making rustic pictures out of strips out of old Lath from Plaster and Lath walls. Today it is commonly made from lattice, lumber stickers and weathered lobster traps. Beach scenes and rural scenes are the… … Wikipedia
lath — lathlike, adj. /lath, lahth/, n., pl. laths /ladhz, laths, lahdhz, lahths/, v. n. 1. a thin, narrow strip of wood, used with other strips to form latticework, a backing for plaster or stucco, a support for slates and other roofing materials, etc … Universalium
plaster — plasterer, n. plasteriness, n. plasterlike, plastery, adj. /plas teuhr, plah steuhr/, n. 1. a composition, as of lime or gypsum, sand, water, and sometimes hair or other fiber, applied in a pasty form to walls, ceilings, etc., and allowed to… … Universalium