Reflected-wave switching

Reflected-wave switching

Reflected-wave switching is a signalling technique used in backplane computer buses such as PCI.

A backplane computer bus is a type of multilayer printed circuit board that has at least one (almost) solid layer of copper called the ground plane, and at least one layer of copper tracks that are used as wires for the signals. Each signal travels along a transmission line formed by its track and the narrow strip of ground plane directly beneath it. This structure is called a microstrip line, by analogy with the stripline used in radio engineering.

Each signal travels from a transmitter to one or more receivers. Most computer buses use binary digital signals, which are sequences of pulses of fixed amplitude. In order to receive the correct data, the receiver must detect each pulse once, and only once. To ensure this, the designer must take the high-frequency characteristics of the microstrip into account.

When a pulse is launched into the microstrip by the transmitter, its amplitude depends on the ratio of the impedances of the transmitter and the microstrip. The impedance of the transmitter is simply its output resistance. The impedance of the microstrip is its characteristic impedance, which depends on its dimensions and on the materials used in the backplane's construction. As the leading edge of the pulse (the "incident wave") passes the receiver, it may or may not have sufficient amplitude to be detected. If it does, then the system is said to use "incident-wave switching". This is the system used in most computer buses predating PCI, such as the VME bus.

When the pulse reaches the end of the microstrip, its behaviour depends on the circuit conditions at this point. If the microstrip is correctly terminated (usually with a combination of resistors), the pulse is absorbed and its energy is converted to heat. This is the case in an incident-wave switching bus. If, on the other hand, there is no termination at the end of the microstrip, and the pulse encounters an open circuit, it is reflected back towards its source. As this "reflected wave" travels back along the microstrip, its amplitude is added to that of the original pulse. As the reflected wave passes the receiver for a second time, this time from the opposite direction, it now has enough amplitude to be detected. This is what happens in a "reflected-wave switching" bus.

In incident-wave switching buses, reflections from the end of the bus are undesirable and must be prevented by adding termination. Terminating an incident-wave trace varies in complexity from a DC-balanced, AC-coupled termination to a single resistor series terminator, but all incident wave terminations consume both power and space (Johnson and Graham, 1993).

Reflected-wave switching is used because it removes the need for resistors to terminate the bus. Reflected-wave buses are therefore suitable for low-cost, low-power, consumer applicationssuch as the PCI bus used in personal computers. One drawback of reflected-wave switching is that each pulse may need to travel twice the length of the backplane (one complete journey for the incident wave, and another for the reflected wave), so a delay must be maintained between adjacent pulses to allow for the travel time. This limits the maximum frequency at which the bus can be operated. The travel time can be calculated by dividing the round-trip length of the bus by the speed of propagation of the signal (which is roughly one half to two-thirds of "c", the speed of light in vacuum).


*Johnson, Howard; Graham, Martin (1993). "High Speed Digital Design". Prentice Hall. ISBN 0-13-395724-1.

Wikimedia Foundation. 2010.

Look at other dictionaries:

  • Q-switching — Q switching, sometimes known as giant pulse formation, is a technique by which a laser can be made to produce a pulsed output beam. The technique allows the production of light pulses with extremely high (gigawatt) peak power, much higher than… …   Wikipedia

  • Spin wave — Spin waves are propagating disturbances in the ordering of magnetic materials. These low lying collective excitations occur in magnetic lattices with continuous symmetry. From the equivalent quasiparticle point of view, spin waves are known as… …   Wikipedia

  • Peripheral Component Interconnect — Infobox Computer Hardware Bus name = PCI fullname = peripheral component interconnection caption = Five 5V 32 bit PCI expansion slots on a motherboard invent date = July 1993 invent name = Intel super date = 2004 super name = PCI Express width =… …   Wikipedia

  • Peripheral Component Interconnect — Este artículo o sección necesita referencias que aparezcan en una publicación acreditada, como revistas especializadas, monografías, prensa diaria o páginas de Internet fidedignas. Puedes añadirlas así o avisar …   Wikipedia Español

  • Conventional PCI — PCI Local Bus Three 5 volt 32 bit PCI expansion slots on a motherboard (PC bracket on left side) …   Wikipedia

  • Optics — For the book by Sir Isaac Newton, see Opticks. Optical redirects here. For the musical artist, see Optical (artist). Optics includes study of dispersion of light. Optics is the branch of …   Wikipedia

  • telecommunications media — Introduction       equipment and systems metal wire, terrestrial and satellite radio, and optical fibre employed in the transmission of electromagnetic signals. Transmission media and the problem of signal degradation       Every… …   Universalium

  • Business and Industry Review — ▪ 1999 Introduction Overview        Annual Average Rates of Growth of Manufacturing Output, 1980 97, Table Pattern of Output, 1994 97, Table Index Numbers of Production, Employment, and Productivity in Manufacturing Industries, Table (For Annual… …   Universalium

  • History of radar — The history of radar starts with experiments by Heinrich Hertz in the late 19th century that showed that radio waves were reflected by metallic objects. This possibility was suggested in James Clerk Maxwell s seminal work on electromagnetism.… …   Wikipedia

  • United Kingdom — a kingdom in NW Europe, consisting of Great Britain and Northern Ireland: formerly comprising Great Britain and Ireland 1801 1922. 58,610,182; 94,242 sq. mi. (244,100 sq. km). Cap.: London. Abbr.: U.K. Official name, United Kingdom of Great… …   Universalium