- Twist-beam rear suspension
The Twist-beam rear suspension is a type of automobile suspension based on a large H shaped member. The front of the H attaches to the body via rubber
bushings, and the rear of the H carries each wheel, on each side of the car. The cross beam of the H holds the two trailing arms together, and provides the roll stiffness of the suspension, by twisting as the two trailing arms move vertically, relative to each other.
The coil springs usually bear on a pad alongside, or behind, the wheels. Often the shock is colinear with the spring, to form a coilover. This location gives them a very high motion ratio compared with most suspensions, which improves their performance, and reduces their weight.
The longitudinal location of the cross beam controls important parameters of the suspension's behaviour, such as the
roll steercurve and toeand cambercompliance. The closer the cross beam to the axle stubs the more the camber and toe changes under deflection. A key difference between the camber and toe changes of a twist beam vs independent suspension is the change in camber and toe is dependent on the position of the other wheel, not the car's chassis. In a traditional independent suspension the camber and toe are based on the position of the wheel relative to the body. If both wheels compress together their camber and toe will not change. Thus if both wheels started perpendicular to the road and car compressed together they will stay perpendicular to the road. The camber and toe changes are the result of one wheel being compressed relative to the other. [http://www.ulsab-avc.org/ulsas/Twistbeam/SystemPhilos_TB2.pdf]
This suspension is used on a wide variety of front wheel drive cars, and was almost ubiquitous on European superminis. It was probably introduced on the
Audi 50,Fact|date=February 2007 which was rebadged as the Volkswagen Polo.
This suspension is usually described as semi-independent, meaning that the two wheels can move relative to each other, but their motion is still somewhat inter-linked, to a greater extent than in a true IRS. This limits the handling of the vehicle, and VW have dropped it in favour of a true IRS for the Golf Mk V in response to the Ford Focus' Control Blade rear suspension.
*Can be durable
*Neat package, reduces clutter under floor
*Fairly light weight
*Springs and shocks can be light and cheap
*No need for a separate
*Basic toe vs lateral force characteristic is
*Since toe characteristics may be unsuitable, adding toe-control
bushingsmay be expensive.
*Camber characteristics are very limited.
*Not very easy to adjust roll stiffness
*Welds see a lot of fatigue, may need a lot of development
*Not much recession compliance - can be poor for impact harshness, and will cause unwelcome toe changes (steer effects)
*Wheel moves forward as it rises, can also be poor for impact harshness
*Need to package room for exhaust and so on past the cross beam
*Camber compliance may be high
* [http://www.tubenet.org.uk/technical/vallf.jpgA picture of a twist beam]
* [http://www.ika.rwth-aachen.de/forschung/veroeffentlichung/1998/1998-2/Im05.gifToe and camber curve for a twist beam]
Wikimedia Foundation. 2010.
Look at other dictionaries:
twist-beam rear axle — See semi independent suspension … Dictionary of automotive terms
Suspension (vehicle) — Suspension is the term given to the system of springs, shock absorbers and linkages that connects a vehicle to its wheels. Suspension systems serve a dual purpose – contributing to the car s handling and braking for good active safety and driving … Wikipedia
Beam axle — Solid axle and Panhard rod on a 2002 Mazda MPV A beam axle is a suspension system, also called a solid axle, in which one set of wheels is connected laterally by a single beam or shaft. A live axle is a type of beam axle in which the shaft (or… … Wikipedia
Torsion beam suspension — A torsion bar suspension, also known as a torsion spring suspension or incorrectly torsion beam, is a general term for any vehicle suspension that uses a torsion bar as its main weight bearing spring. One end of a long metal bar is attached… … Wikipedia
Automotive suspension design — is an aspect of automotive engineering, concerned with designing the suspension for cars and trucks.The process entails *selecting appropriate vehicle level targets *selecting a system architecture *choosing the location of the hard points , or… … Wikipedia
Ford Focus (international) — This is the article about the European and worldwide Ford Focus. For the Focus sold in North America, see Ford Focus (North America). Infobox Automobile name = Ford Focus (International) manufacturer = Ford Motor Company production = 1998 present … Wikipedia
Volkswagen Jetta — Infobox Automobile name = Volkswagen Jetta aka = Volkswagen Atlantic Volkswagen Bora Volkswagen City Jetta Volkswagen Fox Volkswagen Sagitar Volkswagen Vento manufacturer = Volkswagen parent company = Volkswagen Group (Volkswagen AG) production … Wikipedia
Volkswagen Polo — Manufacturer Volkswagen Production 1975–present … Wikipedia
Volkswagen Golf Mk1 — Infobox Automobile generation name = Volkswagen Golf Mk1 manufacturer = Volkswagen aka = Volkswagen Rabbit Volkswagen Caribe Volkswagen CitiGolf Volkswagen Cabriolet Volkswagen Caddy production = 6.8 million unitscite book |last= |first=… … Wikipedia
Daewoo Matiz — Class City car Manufacturer GM Korea … Wikipedia