Scrub radius


Scrub radius
Scrubradius 0 (top) positive (center) negative(bottom)

The scrub radius is the distance in front view between the king pin axis and the center of the contact patch of the wheel, where both would theoretically touch the road.

The kingpin axis is the line between the upper and lower ball joints of the hub. On a MacPherson strut, the top pivot point is the strut bearing, and the bottom point is the lower ball joint. The inclination of the steering axis is measured as the angle between the steering axis and the centerline of the wheel. This means that if the camber angle is adjustable within the pivot points the scrub radius can be changed, this alters the width and offset of the tires on a vehicle.

If the kingpin axis intersection point is outboard of the center of the contact patch it is negative, if inside the contact patch it is positive. The term scrub radius derives from the fact that either in the positive or negative mode, the tire does not turn on its centerline (it scrubs the road in a turn) and due to the increased friction, more effort is needed to turn the wheel[citation needed].

Large positive values of scrub radius, 4 inches or 100 mm or so, were used in cars for many years. The advantage of this is that the tire rolls as the wheel is steered, which reduces the effort when parking. This also allows greater width in the engine bay, which is very important in some compact sports cars.

If the scrub radius is small then the contact patch is spun in place when parking, which takes a lot more effort. The advantage of a small scrub radius is that the steering becomes less sensitive to braking inputs, in particular.

An advantage of a negative scrub radius is that the geometry naturally compensates for split mu braking, or failure in one of the brake circuits. It also provides center point steering in the event of a tire deflation, which provides greater stability and steering control in this emergency situation.

Contents

Steering axis inclination

The steering axis inclination (SAI) is the angle between the centerline of the steering axis and vertical line from center contact area of the tire (as viewed from the front).

Effects of SAI

SAI urges the wheels to a straight ahead position after a turn. By inclining the steering axis inward, it causes the spindle to rise and fall as the wheels are turned in one direction or the other. Because the tire cannot be forced into the ground as the spindle travels in an arc, the tire/wheel assembly raises the suspension and thus causes the tire/wheel assembly to seek the low (center) return point when it is allowed to return. Thus, since it has a tendency to maintain or seek a straight ahead position, less positive caster is needed to maintain directional stability. A vehicle provides stable handling without any of the drawbacks of high positive caster because of SAI.

Scrub radius

The scrub radius is the distance at the road surface between the tire line and the SAI line extended downward through the steering axis.

The line through the steering axis creates a pivot point around which the tire turns. If these lines intersect at the road surface, a zero scrub radius would be present. When the intersection is below the surface of the road, this is positive scrub radius. Conversely, when the lines intersect above the road, negative scrub radius is present. The point where the steering axis (sai) line contacts the road is the fulcrum pivot point on which the tire is turned. Scrub radius is changed whenever there is a change in wheel o/s as on the t/l where the wheels are pushed outboard causing scrub radius to become more (+). Older cars tended to have very close to zero scrub radius but often on the (+) side, newer cars w/ ABS all have negative scrub radius(that's why all the newer cars have the wheels o/s more inboard)

Squirm

Squirm occurs when the scrub radius is at zero. When the pivot point is in the exact center of the tire footprint, this causes scrubbing action in opposite directions when the wheels are turned. Tire wear and some instability in corners is the result.

Applications in suspension

MacPherson strut equipped vehicles usually have a negative scrub radius. Even though scrub radius in itself is not directly adjustable, it will be changed if the upper steering axis point or spindle angle is changed when adjusting camber. This is the case on a MacPherson strut which has the camber adjustment at the steering knuckle. Because camber is usually kept within 1/4° side to side, the resulting scrub radius difference is negligible.

Negative scrub radius decreases torque steer and improves stability in the event of brake failure. SLA suspensions usually have a positive scrub radius. With this suspension, the scrub radius is not adjustable. The greater the scrub radius (positive or negative), the greater the steering effort and the more road shock and pivot binding that takes place. When the vehicle has been modified with offset wheels, larger tires, height adjustments and side to side camber differences, the scrub radius will be changed and the handling and stability of the vehicle will be affected.

References

  • Reimpell, Jornsen; Helmut Stoll, Jurgen W. Betzler. The Automotive Chassis Engineering Principles. SAE International. ISBN 978-0-7680-0657-5. 

Wikimedia Foundation. 2010.

Look at other dictionaries:

  • scrub radius — The distance from the point where the steering axis intersects the ground to the longitudinal line that runs through the center of the tire s contact patch. Also called steering offset. See negative offset steering …   Dictionary of automotive terms

  • radius — See buffered radius crown radius free radius loaded radius radius rods rolling radius scrub radius static loaded radius turning radius unloaded …   Dictionary of automotive terms

  • Scrub plane — The scrub plane is a type of plane used to remove large amounts of wood from the surface of lumber, such as when eliminating cup or twist in the first stages of preparing rough stock, or when reducing the thickness of a board significantly. Scrub …   Wikipedia

  • Wheel sizing — The wheel size for a motor vehicle or similar wheel has a number of parameters. Contents 1 Bolt pattern 2 Bolt circle 2.1 Determining the bolt circle 3 Lug n …   Wikipedia

  • Tricycle — For other uses, see Tricycle (disambiguation). A tricycle (often abbreviated to trike) is a three wheeled vehicle. While tricycles are often associated with the small three wheeled vehicles used by pre school age children, they are also used by… …   Wikipedia

  • Подвеска автомобиля — …   Википедия

  • Pontiac Fiero — Infobox Automobile name = Pontiac Fiero manufacturer = General Motors class = Sports car body style = 2 door notchback 2 door fastback engine = 2.5 L (151 in³) Tech IV I4 2.8 L (173 in³) L44 V6 transmission=4 speed manual 5 speed Getrag 282… …   Wikipedia

  • Double wishbone suspension — Wishbones and upright painted yellow In automobiles, a double wishbone (or upper and lower A arm) suspension is an independent suspension design using two (occasionally parallel) wishbone shaped arms to locate the wheel. Each wishbone or arm has… …   Wikipedia

  • Dual ball joint suspension — A dual ball joint suspension uses a pair of arms, one in tension, one in compression, to replace a wishbone, in a MacPherson or SLA suspension. The outer end of each arm terminates in a ball joint, hence the name. Contents 1 General description 2 …   Wikipedia

  • Automotive suspension design — is an aspect of automotive engineering, concerned with designing the suspension for cars and trucks.The process entails *selecting appropriate vehicle level targets *selecting a system architecture *choosing the location of the hard points , or… …   Wikipedia