Wheel sizing

Wheel sizing

The wheel size for a motor vehicle or similar wheel has a number of parameters.

Contents

Bolt pattern

The bolt pattern is the number of lug nuts or wheel studs on the wheel hub. As the bolts are most often evenly spaced, the number of bolts determines the pattern. For example: smaller cars have three (Citroën 2CV, Renault 4, some Peugeot 106s and Citroën Saxos, and the Tata Nano). Compact cars may have four bolts. Most United States passenger cars have five bolts. Pickup trucks and large SUVs can have as many as six or eight.

Bolt circle

4 Hole Pattern
5 Hole Pattern

The bolt circle is the notional circle determined by the positions of the bolts. The center of every bolt lies on the circumference of the bolt circle. The important measurement is the bolt circle diameter (BCD),[1] also called the pitch circle diameter (PCD).[2]

The BCD may be expressed in millimeters or inches, and is usually given with the number of bolts. For example, a 1974 MG B has a 4/4.5 inch (4/114.3 mm) wheel hub, meaning it has a 4-bolt pattern with a 4.5 inch (114.3 mm) bolt circle diameter.

The most common BCD values are 100 mm (≈3.94 inches) and 4.5 inches (114.3 mm).

Special BCD values are: 95.25 mm (for MGF and Rover Metro), 98 mm (for Fiat group automobiles), 101 mm (for Mini, MG, Austin Metro), 100 or 105 mm (for some GM vehicles), 108 mm (mostly for PSA, Ford and Lincoln), 110 mm (for some GM vehicles), 112 mm (for Mercedes-Benz and some VW group vehicles), 115 mm (for some GM vehicles), 120 mm (mostly for BMW), 130 mm (for Porsche), 170 mm (for Saab 96).

Determining the bolt circle

For a 4- or 6-bolt wheel, this measurement is merely the distance between the center of two diametrically opposite bolts. In the 4-bolt picture to the right, this would be the distance between holes #1 and #4, for example.

Some basic geometry is needed to find the center of a 5-bolt pattern. In practice, the BCD can be found by multiplying the center distance between any two adjacent holes by 1.701.

Generally, the BCD b can be calculated for any wheel from the number of bolts n and the center distance d between two adjacent bolts as: b = \frac{d}{\sin \left( \frac{1}{n}180 \right) }.

Lug nuts or bolts

Wheels must be fitted with the correct type of lug nuts on wheel studs, or bolts. Lug (aka wheel nuts in British English) nuts are usually either flat, tapered (generally at 60 degrees and referred to as conical seat), or ball seats, meaning the mounting surfaces are flat, tapered, or spherical respectively.

Most Mercedes have ball lug seats from the factory while most aftermarket wheels have a tapered lug design. Wrong lug nuts for the wheel will not properly center it and cause wobble. Some manufacturers (e.g. Toyota and Lexus) have used taper lug nuts for steel wheels and flat seated lug nuts for alloy wheels.

Some aftermarket wheels will only fit smaller lug nuts, or not allow an ordinary lug nut to be properly torqued down because a socket will not fit into the lug hole. Tuner lug nuts were created to solve this problem by utilizing a special key to allow removal and installation with standard lug wrench or socket. The design of tuner lug nuts can range from bit style to multisided or spline drive, and are sometimes lightweight for performance purposes.

A variation is the "locking wheel nut", which is almost universally used for alloy wheels in the United Kingdom. One standard lug nut on each wheel is replaced with a nut which requires a special and unique key (typically a computer-designed, rounded star shape) to fit and remove the nut. This helps to discourage theft of wheels. However, universal removal tools are available which grip the head of the locking nut using a hardened left-hand thread. The success of these depends on whether there is room to use it in the lug hole, and whether the manufacturer has incorporated a free-spinning outer casing to the lock. Keeping an appropriate tool to lock and unlock aftermarket nuts, and a spare set of nuts, with the spare tire in the boot of the car is recommended by manufacturers.

Offset

The offset, measured in millimeters, can be negative or positive, and is the distance from the hub-mounting surface to the rim's true centerline. A positive offset means the hub-mounting surface is closer to the outside edge of the wheel, i.e. the wheel wraps around the hub and brake hardware more deeply; a negative offset means the hub-mounting surface is closer to the inside edge of the wheel and wheel sticks outwards more than inwards.

When selecting aftermarket wheels, a wheel with too little positive offset will be closer to edge of the fender, and one with too much positive offset will tuck inside the fender and be closer to the suspension components. Wheel width, offset and tire size all determine the way a particular wheel/tire combination will work on a given car. Offset also affects the scrub radius of the steering and it is advisable to stay within the limits allowed by the vehicle manufacturer. Because wheel offset changes the lever-arm length between the center of the tire and the centerline of the steering knuckle, the way bumps, road imperfections and acceleration and braking forces are translated to steering torques (bump-steer, torque-steer, etc.) will change depending on wheel offset. Likewise, the wheel bearings will see increased thrust loads if the wheel centerline is moved away from the bearing centerline.

Wheel size

Measuring an outside rim diameter to approximate wheel size
Asanti wheel on a Hummer H2

The wheel size is the diameter of the wheel in inches where the beads of the tire sit on the wheel. This measurement does not include the rim flange. Modern road tires have several measurements associated with their size as specified by tire codes like 225/70R14. The first number in the code (e.g., "225") represents the nominal tire width in millimeters. This is followed by the aspect ratio (e.g.,"70"), which is the height of the side wall expressed as a percentage of the nominal width. "R" stands for radial and relates to the tire construction. The final number in the code (e.g.,"14") is the rim size measured in inches. The overall circumference of the tire will increase by increasing any of the tire's specifications. For example increasing the width of the tire will also increase its circumference, because the side wall height is a proportional length. Increasing the aspect ratio will increase the height of the tire and hence the circumference.

Off-roading tires may use a different measurement scheme: outside diameter times(by) tread width, followed by rim size (all in inches) - for example 31x10.50R15. The size of the disc however is denoted like 8.5" X 20.0". This shall mean that the width (of thickness) of the wheel is 8.5 inches and the diameter is 20 inches.

A dub is a custom wheel that has a wheel size of 20 inches or greater; the term dub is a slang term for twenty. DUBS may have originated as an abbreviation for double-deuces, or 22 in wheels. DUB Magazine, an automotive enthusiasts magazine, takes its name from the term and covers material chiefly pertaining to urban vehicles and the people that own them.

Centerbore

The centerbore of a wheel is the size of the hole in the back of the wheel that centers it over the mounting hub of the car. Some factory wheels have a centerbore that matches exactly with the hub to reduce vibration by keeping the wheel centered. Wheels with the correct centerbore to the car they will be mounted on are known as hubcentric. Hubcentric wheels take the stress off the lug nuts, reducing the job of the lug nuts to center the wheel to the car. Wheels that are not hubcentric are known as lugcentric, as the job of centering is done by the lug nuts assuming they are properly torqued down.

Centerbore on aftermarket wheels must be equal to or greater than that of the hub, otherwise the wheel cannot be mounted on the car. Many aftermarket wheels come with "hubcentric rings" that lock or slide into the back of the wheel to adapt a wheel with a larger centerbore to a smaller hub.[3] These adapters are usually made of plastic but also in aluminum.

X-factor

Caliper Clearance (X-factor): The amount of clearance built into the wheel to allow for the vehicle's disc brake and caliper assembly.

Load capacity

Load capacity is the amount of weight a wheel will carry. This number will vary depending on the number of lugs, the PCD, the material used and the type of axle the wheel is used on. A wheel used on a free rolling trailer axle will carry more weight than that same wheel used on the drive or steering axle of a vehicle. All wheels will have the load capacity stamped on the back of the wheel.

GVWR

This is the Gross Vehicle Weight Rating. In the United States this information is required to be on the vehicle's door placard. The load capacity of the total number of wheels on the vehicle combined must meet or exceed the vehicle's GVWR.

References

  1. ^ "Bolt Circle Diameter (B.C.D.)". Sheldon Brown's Bicycle Glossary. http://www.sheldonbrown.com/gloss_bo-z.html#bcd. Retrieved 3 Dec 2010. 
  2. ^ "P.C.D.". Sheldon Brown's Bicycle Glossary. http://www.sheldonbrown.com/gloss_p.html#pcd. Retrieved 3 Dec 2010. 
  3. ^ "Hubcentric-rings.com". Why hub centric rings?. http://www.hubcentric-rings.com/miksi_soviterengas/. Retrieved 21 Mar 2011. 

See also


Wikimedia Foundation. 2010.

Игры ⚽ Нужен реферат?

Look at other dictionaries:

  • Wheel — A wheel is a circular device that is capable of rotating on its axis, facilitating movement or transportation whilst supporting a load (mass), or performing labour in machines. A wheel, together with an axle overcomes friction by facilitating… …   Wikipedia

  • Alloy wheel — on a passenger car Alloy wheels are automobile (car, motorcycle and truck) wheels which are made from an alloy of aluminium or magnesium. They are typically lighter for the same strength and provide better heat conduction and improved cosmetic… …   Wikipedia

  • Plus sizing — is the practice of changing a specific tire to a larger size while compensating with reductions in other aspects of the tire s size so that the new tire has the same diameter and circumference as the original tire to prevent any changes in… …   Wikipedia

  • Bicycle wheel — For the Marcel Duchamp installation, see Bicycle Wheel. The front wheel from a racing bicycle made using a Mavic rim …   Wikipedia

  • Tire code — Automobile tires are described by an alphanumeric tire code (in American English) or tyre code (in British English, Australian English and others), which is generally molded into the sidewall of the tire. This code specifies the dimensions of the …   Wikipedia

  • PCD — may refer to: Partido Conservador Demócrata, a political party in Nicaragua Partnership for Child Development, seeks to improve health and nutrition in school age children in low income countries, formed in 1992 Pussycat Dolls, an American pop… …   Wikipedia

  • textile — /teks tuyl, til/, n. 1. any cloth or goods produced by weaving, knitting, or felting. 2. a material, as a fiber or yarn, used in or suitable for weaving: Glass can be used as a textile. adj. 3. woven or capable of being woven: textile fabrics. 4 …   Universalium

  • abrasive — abrasively, adv. abrasiveness, n. /euh bray siv, ziv/, n. 1. any material or substance used for grinding, polishing, etc., as emery, pumice, or sandpaper. adj. 2. tending to abrade; causing abrasion; abrading. 3. tending to annoy or cause ill… …   Universalium

  • Mountain bike — This article is about mountain bikes themselves. For the associated activity, see Mountain biking. A full suspension mountain bike A mountain bike or mountain bicycle (abbreviated MTB or ATB (all terrain bicycle)) is a bicycle created for off… …   Wikipedia

  • 29er (bicycle) — 29ers or Two niners are mountain bikes that are built to use 700c or ISO 622 mm wheels. [ [http://www.mtbr.com/29er 29er Mountain Bikes 29 inch mountain bikes Mtbr.com ] ] Most mountain bicycles use ISO 559 mm wheels which are commonly called 26… …   Wikipedia

Share the article and excerpts

Direct link
Do a right-click on the link above
and select “Copy Link”