Directional boring

Directional boring
A small directional boring unit in action

Directional boring, commonly called horizontal directional drilling or HDD, is a steerable trenchless method of installing underground pipes, conduits and cables in a shallow arc along a prescribed bore path by using a surface launched drilling rig, with minimal impact on the surrounding area. Directional boring is used when trenching or excavating is not practical. It is suitable for a variety of soil conditions and jobs including road, landscape and river crossings. Installation lengths up to 6,500’ (2,000m) have been completed, and diameters up to 56" (1,200mm) have been installed in shorter runs. Pipes can be made of materials such as PVC, polyethylene, polypropylene, Ductile iron, and steel if the pipes can be pulled through the drilled hole. Directional boring is not practical if there are voids in the rock or incomplete layers of rock. The best material is solid rock or sedimentary material. Soils with cobble stone are not recommended. There are different types of heads used in the pilot-hole process, and they depend on the geological material.

Contents

Equipment

The equipment used in a directional drill operation depends on the size of the pipe, length of the run, and surrounding locations. For the large bores, a 100,000-pound pulling power drill is used with a reclaimer, excavator, and multiple pumps and hoses to move the fluid. The drilling steel is a 3-in. diameter pipe with male and female threads. The head of the operation comes in multiple designs and depends on the rock or soil being penetrated. The drilling head has multiple water ports to allow removal of material. A talon bit involves the carbide-tipped cutters. These allow for steering and cutting the material. Another head is a mud-motor that is used in rocky landscapes.

Furthermore, other equipment is needed to assist directional-drill or HDD to work smoothly, such as drilling mud recycling system, shale shaker, mud cleaner, centrifugal pump, mud tanks, etc.

Technique

Directional boring is used for installing infrastructure such as telecommunications and power cable conduits, water lines, sewer lines, gas lines, oil lines, product pipelines, and environmental remediation casings. It is used for crossing waterways, roadways, shore approaches, congested areas, environmentally sensitive areas, and areas where other methods are costlier. It is used instead of other techniques to provide less traffic disruption, lower cost, deeper and/or longer installation, no access pit, shorter completion times, directional capabilities, and environmental safety.

The technique has extensive use in urban areas for developing subsurface utilities as it helps in avoiding extensive open cut trenches. The use requires that the operator have complete information about existing utilities so that he can plan the alignment to avoid damaging those utilities. Since uncontrolled drilling can lead to damage, different agencies/government authorities owning the urban right-of-way or the utilities have rules for safe work execution. For standardization of the techniques, different trenchless technology promoting organizations have developed guidelines for this technique.

Process

Starting pit with pilot hole and some drilling fluid in the pit

The process starts with receiving hole and entrance pits. These pits will allow the drilling fluid to be collected and reclaimed to reduce costs and prevent waste. The first stage drills a pilot hole on the designed path, and the second stage enlarges the hole by passing a larger cutting tool known as the back reamer. The reamer's diameter depends on the size of the pipe. The driller increases the diameter according to the material being cut and to achieve optimal production. The third stage places the product or casing pipe in the enlarged hole by way of the drill steel; it is pulled behind the reamer to allow centering of the pipe in the newly reamed path.

Horizontal directional drilling is done with the help of a viscous fluid known as drilling fluid. It is a mixture of water and, usually, bentonite or polymer continuously pumped to the cutting head or drill bit to facilitate the removal of cuttings, stabilize the bore hole, cool the cutting head, and lubricate the passage of the product pipe. The drilling fluid is sent into a machine called a reclaimer which removes the drill cuttings and maintains the proper viscosity of the fluid.

Locating and guidance

Empty conduits laid by directional boring

Location and guidance of the drilling is an important part of the drilling operation, as the drilling head is under the ground while drilling and, in most cases, not visible from the ground surface. Uncontrolled or unguided drilling can lead to substantial destruction, which can be eliminated by properly locating and guiding the drill head.

There are three types of locating equipment for locating the bore head: the walk-over locating system, the wire-line locating system and the gyro guided drilling, where a full inertial navigation system is located close to the drill head. In first both systems a sonde, or transmitter, behind the bore head registers angle, rotation, direction, and temperature data. This information is encoded into an electro-magnetic signal and transmitted through the ground to the surface in a walk-over system. At the surface a receiver (usually a hand-held locator) is manually positioned over the sonde, the signal is decoded and steering directions are relayed to the bore machine operator. In a wire-line system, this information is transmitted through the cable fitted within the drill string. Those both systems have their own merits, and a particular system is chosen depending upon the site requirements. The gyro based system is fully autonomously working and therefore one of the most accurate system where sufficient diameter (200 mm) is available and where long distances (up to 2 km) have to be performed with small deviation (less than 1 m posiition error).

See also

References

  • Willoughby, David (2005). Horizontal Directional Drilling, p. 1-263. Mcgraw-Hill, New York. ISBN 007145473X.
  • Short, Jim (1993). Introduction to Directional and Horizontal Drilling, p. 1-222. PennWell Books, Tulsa, Oklahoma. ISBN 0878143955.
  • v. Hinueber, Edgar (2006). Most accurate drilling guidance by dead-reckoning using high precision optical gyroscopes, Proceedings NoDig Conference of Horizontal Directional Drilling, Brisbane 2006.

External links


Wikimedia Foundation. 2010.

Игры ⚽ Поможем сделать НИР

Look at other dictionaries:

  • Directional drilling — A horizontal directional drill in operation Directional drilling (or slant drilling) is the practice of drilling non vertical wells. It can be broken down into three main groups: Oilfield Directional Drilling, Utility Installation Directional… …   Wikipedia

  • Tunnel boring machine — A tunnel boring machine that was used at Yucca Mountain nuclear waste repository A tunnel boring machine (TBM) also known as a mole , is a machine used to excavate tunnels with a circular cross section through a variety of soil and rock strata.… …   Wikipedia

  • Clean Harbors — Inc. Type Public Traded as NYSE: CLH …   Wikipedia

  • Trenchless technology — Trenchless technology, as the name implies, stands for subsurface construction works where less trenches or no continuous trenches are required to be dug. It is a rapidly growing sector of the construction and civil engineering industry. It can… …   Wikipedia

  • StraightLine HDD — Infobox Company company name=StraightLine HDD company logo= company type=Private foundation= Kansas, United States (January 1, 1984, as StraightLine Manufacturing, Inc.) location city= flagicon|USA 1816 E. Wasp Rd., Hutchinson, Kansas 67501… …   Wikipedia

  • Microtunneling — As the name implies, microtunneling is a digging technique used to construct small tunnels. These small diameter tunnels make it impossible to have an operator in the machine itself. Instead, the microtunnel boring machine (MTBM) must be operated …   Wikipedia

  • Rotary steerable system — A rotary steerable system is a new form of drilling technology used in directional drilling. It employs the use of specialized downhole equipment to replace conventional directional tools such as mud motors.They are generally programmed by the… …   Wikipedia

  • Forage dirigé — Un forage dirigé sous une ville Le forage directionnel (ou forage oblique) est un forage non vertical. Il peut être décomposé en trois groupes principaux: les forages directionnels pétroliers, les forages directionnels utilitaires  …   Wikipédia en Français

  • RJV Gas Field Services — Infobox Company company name = RJV Gas Field Services company company type = Public company slogan = foundation = Calgary, Alberta (1976) location = Calgary, Alberta key people = Dale Laniuk, CEO, Paul Casey, CFO revenue = ) industry = Oil and… …   Wikipedia

  • Pipe ramming — is a trenchless method for installation of steel pipes and casings over distances usually up to 30m (150 ft) up long and up to 1,500mm (60 inches) in diameter, although the method can be used for much longer and larger installations. The method… …   Wikipedia

Share the article and excerpts

Direct link
Do a right-click on the link above
and select “Copy Link”