Effective porosity

Effective porosity

The term effective porosity lacks a single or straightforward definition. Even some of the terms used in its mathematical description (“Vcl” and “Vsh”) have multiple definitions. However, it is most commonly considered to represent the porosity of a rock excluding water bound to clay particles - i.e. what proportion of the rock comprises voids through which fluids - such as water and oil - can freely pass. The effective porosity is of great importance in considering the suitability of rocks as oil reservoir rocks.


thumb|350px|Fig. 1: ">

This figure represents the components of the gross rock (bulk) volume as a strip. The individual components are not to scale. For example, porosity and pore volume are over-emphasised for illustrative purposes.

adapted from Eslinger and Pevear [Eslinger, E. and Pevear, D. “Clay Minerals for Petroleum Geologists and Engineers”, SEPM Short Course No. 22, 1988.]

Figure 1 illustrates core and log derivations of porosity for a sandstone and infers (some) different definitions of effective porosity.

The figure is discussed below going from left to right along the strip.

1. “Quartz” (more aptly termed “non-clay minerals”) forms part of the matrix, or in core analysis terms, part of the grain volume.

2. “Clay Layers” are dry clay (Vcl) which also form part of the grain volume. If a core sample is dried in a normal dry oven (non-humidified atmosphere) the clay layers and quartz together form the grain volume, with all other components constituting core analysis “total porosity” (notwithstanding comments in (6) below). This core total porosity will generally be equivalent to the total porosity derived from the density log when representative values for matrix and fluid density are used.

The clay layers contain OH- groups (often termed “structural water”). This structural water is never part of the pore volume. However, since neutron logs sense H (hydrogen) and all hydrogen so-sensed is allocated as pore space, then neutron logs will overestimate porosity in argillaceous rocks by sensing OH- as part of the pore space.

3. “Clay Surfaces and Interlayers” comprise electrochemically bound water (clay-bound water or CBW) which varies in volume according to the clay-type, and the salinity of the formation water (see the Attachments section). The most common definition of effective porosity for sandstones excludes CBW as part of the porosity, whereas CBW is included as part of the total porosity.Worthington, P.F. “Conjunctive interpretation of core and log data through association of effective and total porosity models” In: Harvey, P.K. & Lovell, M.A. ( eds), Core-LogIntegration, Geological Society, London, Special Publications, 136, 213-223.] Adams, S., “Porosity—Total vs Effective”, WellEval.com website, 2005] That is:

Effective porosity = Total porosity - CBW

To assess the effective porosity, samples are dried at 40-45% relative humidity and 60 °C. This means that one to two molecular layers of CBW can be retained, and a form of “effective porosity” can be measured on the samples. However, the CBW retained by the humidity-dried core plugs is not necessarily representative of CBW in the formation at reservoir conditions. This lack of reservoir representation occurs not only because CBW tends to a minimum value in cores humidity-dried at the specified conditionsBush, D.C. and Jenkins, R.E., “Proper Hydration of Clays for Rock Property Determination”, SPE 2589, JPT, July 1970, 800-804.] but also because the amount of CBW at reservoir conditions varies with the salinity of formation water in the “effective” pore space.Hill, H.J., Shirley, O.J., Klein, G.E. “Bound Water in Shaly Sands—Its Relation to Qv and Other Formation Properties”, Log Analyst, May-June, 1979.] Juhasz, I. “Conversion of routine air permeability data into stressed brine-permeability data” Tenth European Formation Evaluation Symposium, paper Y, 1986.] Humidity-dried cores have no water in the “effective” pore space, and therefore can never truly represent the reservoir CBW condition. A further complication can arise in that humidity drying of cores may sometimes leave water of condensation in clay-free micropores (ref. 7).

Log derivation of effective porosity includes CBW as part of the volume of shale (Vsh). Vsh is greater than the volume of Vcl not only because it incorporates CBW, but also because Vsh includes clay size (and silt-size) quartz (and other mineral) grains, not just pure clay.

4. ”Small pores” contain capillary water which is different from CBW in that it is physically (not electrochemically) bound to the rock (by capillary forces). Capillary water generally forms part of the effective pore space for both log and core analysis.However, microporous pore space associated with shales (where water is held by capillary forces and hence is not true CBW) is usually estimated as part of the Vsh by logs and therefore not included as part of the effective porosity. The total water associated with shales is more properly termed “shale water” which is larger in value than CBW (ref. 8). If we humidity dried core samples, (some of) the electrochemically bound CBW would be retained, but none of the capillary-bound microporous water (notwithstanding comments in ref. 7). Therefore, although the figure infers that a humidity-dried core could produce an effective porosity similar to a log analysis effective porosity, the effective porosity from the core will usually be higher (see “Examples” section)—notwithstanding comments in (6) below. Traditionally, true CBW has been directly measured neither on cores nor by logs, although NMR measurement holds promise (ref. 9).

At a given height above the free-water level, the capillary water becomes “irreducible”. This capillary water forms the irreducible water saturation (“Swi”) with respect to effective porosity (notwithstanding the inclusion of microporous water as Vsh during the log analysis) whereas for total porosity, the CBW and capillary water combined form the “Swi”.

5. ”Large pores” contain hydrocarbons (in a hydrocarbon bearing formation). Above the transition zone, only hydrocarbons will flow. Effective porosity (with reference to the figure below) can be classified as only the hydrocarbon-filled large pore spaces above the transition zone (ref. 10).

Anecdotally, effective pore space has been equated to displaceable hydrocarbon pore volume. In this context, if residual hydrocarbon saturation were calculated at 20%, then only 80% of the hydrocarbon-filled pores in the figure would constitute effective pore space.

6. “Isolated pores” in clastics, and most carbonates, make a negligible contribution to porosity. There are exceptions. In some carbonates, for example, the tests of microscopic organisms can become calcified to create significant isolated intra-particular pore space which is not connected to the inter-particular pore space available for hydrocarbon storage and flow. In such cases, core analysis will only record the inter-particular pore space, or “effective porosity”, whereas the density and neutron logs will record the total pore space. Only by crushing the rock can the core analysis yield the total porosity seen by the logs. The traditional Petroleum Engineering and core analysis definition of effective porosity is the sum of the interconnected pore space—that is, excluding isolated pores (ref. 11). Therefore in practice, for the vast majority of sedimentary rocks, this definition of effective porosity equates to total porosity.

ummary of terms

Utilising the Eslinger & Pevear concept, the following terms are illustrated in Figure 2 below.

* Total Porosity: that volume of the reservoir rock which is fluid (oil, water, gas) filled, expressed as a percentage or a fraction of the gross (bulk) rock volume.

* Effective Porosity Φe1: The sum of all the interconnected pore space. In the vast majority of cases, this core analysis and Petroleum Engineering definition of effective porosity equates to total porosity.

* Effective Porosity Φe2: Effective porosity measured on core samples which are dried in a humidity oven so that clays retain one or two molecular layers of bound water—however, this CBW tends to a minimum and is likely not reservoir representative.

* Effective Porosity Φe3: Total porosity minus clay-bound water (CBW).

* Effective Porosity Φe4: Log effective porosity. In essence, total porosity minus shale water, where solid minerals and the volume of shale (Vsh) constitute the matrix (non-effective porosity) and the remaining volume constitutes the effective porosity. For practical purposes, Vsh includes solid clays and the clay-sized and silt-sized fraction of non-clay minerals plus CBW and capillary bound water associated with shale micropores.

* Effective Porosity Φe5: In a hydrocarbon-bearing reservoir above the transition zone, only that pore space which is filled with hydrocarbons. From the NMR log, this equates to the Free Fluid Index (FFI), in other words, all pore space above the T2 cut-off.

* Effective porosity Φe6: That volume of pore space which contains only producible hydrocarbons.

* Clay Bound Water (CBW): Total porosity × SF × QvWhere:

* CBW = Clay bound water * SF = Salinity Factor (0.6425 * S-0.5 + 0.22) * Qv = Cation Exchange Capacity, meq/ml pore space * S = Salinity, g/l


A dramatic example of a core effective porosity vs log effective porosity discrepancy comes from some Greensand reservoirs in Western Australia. Greensands are green because of iron-bearing glauconite which is usually recognized as illite/mica or mixed layer illite-smectite clay by x-ray diffraction. The glauconite "per se" will incorporate electrochemically bound water (CBW) because of the clay types. More importantly for the consideration of effective porosity, though, glauconite grains (part of the Vsh) have intra-particular microporous pore space which retains capillary-bound water. Glauconite can constitute a large percentage of the reservoir rock, and therefore the associated intra-particular pore space can be significant. Log effective porosities calculated at 25% in some Greensand reservoirs have yielded core analysis effective porosities of 35% at equivalent depths.Fact|date=March 2008 The difference is the glauconitic microporosity which contains water at reservoir conditions and is included as part of the Vsh (non-effective porosity) by log analysis. However, glauconitic microporosity is measured as part of the effective porosity in core plugs, even if they are humidity dried.

Greensands may cause varying degrees of difficulty for porosity log analysis. OH- radicals affect neutron logs; the iron component is troublesome, and varying clay hydration needs to be considered for density log interpretation. The iron component affects the NMR logs and clay affects the sonic log. Therefore it is essential to have a core - or at least a good understanding of the geology - before invoking total "vs" effective porosity relationships.

ee also

* Bulk density
* Porosity
* Gas porosity


* Vcl has been expressed as: dry clay (ref. 2); dry clay plus CBW (ref. 10). Vsh has been has been described as: dry clay plus CBW (one version of a “perfect shale”, ref. 8); dry clay, CBW plus silt (the Dual Water “perfect shale” in the diagram above, ref. 12); dry clay, silt, CBW plus shale microporous water (the “practical shale”, ref. 8).

* Different derivations of effective porosity are not necessarily mutually exclusive. Moreover, the unifying underlying theme is interconnected pore space even though unconnected pore space may result from a number of different mechanisms, such as physically isolated pores created by calcified fossils or flow-isolated microporosity.

* No matter what definition of porosity is used, the calculated hydrocarbon-in-place should always be the same. For this reason, hydrocarbon-in-place can be expressed as a percentage of the total (gross) rock volume thereby bypassing the issue of porosity altogether. However, since current logging tools cannot directly sense hydrocarbon alone, the intermediate step of porosity calculation is still a basic necessity.


7. Basan, P., Hook, J.R., Hughes, K.O., Rathmell, J.J., Thomas , D.C. “Measuring Porosity, Saturation and Permeability from Cores: An Appreciation of the Difficulties”, The Technical Review, Vol. 36, No.4, 22-36, Oct. 1988.

8. Elseth, T., Nicolaysen, R., Roberts, D.E.R. “Grain Density Correction of the Density Log: A Core-Log Calibration Method for Improved Porosity Prediction in Mineralized Micaceous Sandstone Reservoirs”, SPWLA 42 nd Annual Logging Symposium, June 17-20, 2001.

9. Martin, P., and Dacy, J. “Effective Qv By NMR Core Tests”, SPWLA 45 th Annual Logging Symposium, June 6-9, 2004.

10. Hook, J.R. “An Introduction to Porosity”, Petrophysics, May-June, 2003.

11. ”Recommended Practices for Core Analysis”, API RP 40, February 1998.

12. Clavier, C., Coates. G., Dumanoir, J. “The Theoretical and Experimental Bases for the ‘Dual Water’ Model for the Interpretation of Shaly Sands”, SPE 6859, 1977.

Wikimedia Foundation. 2010.

Look at other dictionaries:

  • effective porosity —    See porosity, effective …   Lexicon of Cave and Karst Terminology

  • Porosity — or void fraction is a measure of the void (i.e., empty ) spaces in a material, and is a fraction of the volume of voids over the total volume, between 0–1, or as a percentage between 0–100%. The term is used in multiple fields including… …   Wikipedia

  • porosity, tertiary —    Porosity caused by solutional enlargement of secondary porosity.    See also pore; pore space; porosity; porosity, effective; porosity, primary; porosity, secondary …   Lexicon of Cave and Karst Terminology

  • porosity, primary —    Porosity of some lithological material that developed while the rock was forming.    See also interstice; pore; pore space; porosity; porosity, effective; porosity, secondary …   Lexicon of Cave and Karst Terminology

  • porosity, secondary —    Porosity of some lithologic material that has developed after the rock was initially formed, such as joints and fractures, and may be capable of enlargement by dissolution processes.    See also pore; pore space; porosity, effective; porosity …   Lexicon of Cave and Karst Terminology

  • porosity —    1. The ratio of the aggregate volume of interstices in a rock or soil to its total volume; generally stated as a percentage [10].    2. The ratio, usually expressed as a percentage, of the total volume of voids of a given porous medium to the… …   Lexicon of Cave and Karst Terminology

  • Porosity sealing — Porosity sealing, also known as vacuum impregnating, metal impregnating, polymer impregnating, and porous metal sealing, is the process of filling a porous substrate to make it airtight. Process Porosity sealing is a four step process: Air within …   Wikipedia

  • porosity, effective —    1. The ratio, usually expressed as a percentage of the total volume of voids available for fluid transmission to the total volume of the porous medium [22].    2. The ratio of the volume of the voids of a soil or rock mass that can be drained… …   Lexicon of Cave and Karst Terminology

  • Formation evaluation neutron porosity — In the field of formation evaluation, porosity is one of the key measurements to quantify an oil and gas reserves. Neutron porosity measurement employs neutron source to measure hydrogen index in a reservoir, which is directly related to porosity …   Wikipedia

  • stress, effective —    Stress (pressure) that is borne by and transmitted through the grain to grain contacts of a deposit, and thus affects its porosity or void ratio and other physical properties. In onedimensional compression, effective stress is the average… …   Lexicon of Cave and Karst Terminology