- Pressure head
Pressure head is a term used in
fluid mechanicsto represent the internal energyof a fluiddue to the pressureexerted on its container. It may also be called static pressure head or simply static head (but not static head pressure). It is mathematically expressed as::where: is pressure head ( Length, typically in units of m);: is fluid pressure( Forceper unit Area, often as Pa units); and: is the specific weight( Weightper unit volume, typically N·m−3 units): is the densityof the fluid ( Massper unit volume, typically kg·m−3): is acceleration due to gravity (rate of change of velocity, given in m·s−2)
Practical uses for pressure head
Fluid flow is measured with a wide variety of instruments. The
venturi meterin the diagram on the right shows two columns of a measurement fluid at different heights. The height of each column of fluid is proportional to the pressure of the fluid. To demonstrate a classical measurement of pressure head, we could hypothetically replace the working fluidwith another fluid having different physical properties.
For example, if the original fluid was
waterand we replaced it with mercury at the same pressure, we would expect to see a rather different value for pressure head. In fact, the specific weightof water is 9.8 kN/m3 and the specific weight of mercury is 133 kN/m3. So, for any particular measurement of pressure head, the height of the column of water will be about 13.6 times taller than the column of mercury would be (133/9.8 = 13.6). So if a water column meter reads "13.6 cm H2O," then a coinciding measurement is "1.00 cm Hg."
This example demonstrates why there is a bit of confusion surrounding pressure head and its relationship to pressure. Scientists frequently use columns of water (or mercury) to measure pressure, since for a given fluid, pressure head is proportional to pressure. Measuring pressure in units of "mm of mercury" or "inches of water" makes sense for
instrumentation, but these raw measurements of head must frequently be converted to more convenient pressure units using the equations above to solve for pressure.
In summary, pressure head is a measurement of length, which can be converted to the units of pressure, as long as strict attention is paid to the density of the measurement fluid and the local value of g.
Implications for gravitational anomalies on
We would normally use pressure head calculations in areas in which is constant. However, if the gravitational field fluctuates, we can prove that pressure head fluctuates with it.
* If we consider what would happens as gravity "decreases", we would expect the fluid in the venturi meter shown above to withdraw from the pipe "up" into the vertical columns. "Pressure head is increased."
* In the case of zero gravity, the pressure head approaches "
infinity". Fluid in the pipe may "leak out" of the top of the vertical columns (assuming ).
* To simulate negative gravity, we could turn the venturi meter shown above upside down. In this case gravity is negative, and we would expect the fluid in the pipe to "pour out" the vertical columns. Pressure head is negative (assuming ).
* If and , we observe that the "pressure head is also negative", and the ambient air is sucked into the columns shown in the venturi meter above. This is called a "
siphon", and is caused by a partial vacuuminside the vertical columns. In many venturis, the column on the left has fluid in it (), while only the column on the right is a siphon ().
* If and , we observe that the pressure head is again positive, predicting that the venturi meter shown above would look the same, only upside down. In this situation, gravity causes the working fluid to plug the siphon holes, but the fluid doesn't leak out because the ambient pressure is greater than the pressure in the pipe.
* The above situations imply that the
Bernoulli equation, from which we obtain static pressure head, is extremely versatile.
*Derivations of Bernoulli equation
Hydraulic head, which includes a component of pressure head
See [http://www.engineeringtoolbox.com/density-specific-weight-gravity-d_290.html Engineering Toolbox article on Specific Weight] See [http://www.engineeringtoolbox.com/static-pressure-head-d_610.html Engineering Toolbox article on Static Pressure Head]
Wikimedia Foundation. 2010.
Look at other dictionaries:
pressure head — Hydrostatic pressure expressed as the height of a column of water that the pressure can support at the point of measurement . See also head, static; pressure, hydrostatic … Lexicon of Cave and Karst Terminology
pressure head — /ˈprɛʃə hɛd/ (say preshuh hed) noun the pressure of a fluid at a given point in a system divided by the density of the fluid and the acceleration due to gravity … Australian English dictionary
pressure head — Physics. head (def. 32). [1905 10] * * * … Universalium
pressure head — noun : head 14 … Useful english dictionary
pressure, head — Force caused by the weight of a column or body of fluids. Expressed in feet, inches, or psi … Dictionary of automotive terms
head — headlike, adj. /hed/, n. 1. the upper part of the body in humans, joined to the trunk by the neck, containing the brain, eyes, ears, nose, and mouth. 2. the corresponding part of the body in other animals. 3. the head considered as the center of… … Universalium
Pressure — This article is about pressure in the physical sciences. For other uses, see Pressure (disambiguation). Pressure as exerted by particle collisions inside a closed container … Wikipedia
Head (disambiguation) — In anatomy, the head of an animal is the rostral part (from anatomical position) that usually comprises the brain, eyes, ears, nose, and mouth.Metaphorically, Head may refer to a person who is a leader, supervisor or the like, such as the head of … Wikipedia
pressure level — noun the force applied to a unit area of surface; measured in pascals (SI unit) or in dynes (cgs unit) the compressed gas exerts an increased pressure • Syn: ↑pressure, ↑force per unit area • Derivationally related forms: ↑press ( … Useful english dictionary
head, total — The total head of a liquid at a given point is the sum of three components: (a) the elevation head, which is equal to the elevation of the point above a datum, (b) the pressure head, which is the height of a column of static water that can be… … Lexicon of Cave and Karst Terminology