Field hockey stick

Field hockey stick

In Field hockey, each player carries a stick and cannot take part in the game without it. The stick is usually between 36" and 38" long (but this is not defined or restricted)and traditionally made of wood but now almost all the more expensive sticks are 'composite' - made of a number of materials. They usually contain a combination of fibreglass, aramid fiber and carbon fibre in varying proportions according to the characteristics (flexibility; stiffness; resistance to impact and abrasion) required composites.

Early Rules

Although the exact origin of field hockey remains unknown, historians have recorded a number of 4,000-year-old drawings found in the tomb at Beni-Hasen in the Nile Valley (Egypt) which showed men playing the sport. Throughout the following centuries, variations of the game were played by a spectrum of cultures ranging from Greeks and Romans to Ethiopians, Indians and Aztecs. In most of these cultures a single wooden stick with a curved end, probably a sapling or a suitable tree branch, immediately available, was used rather than a purpose 'manufactured' sports item.

Finally after centuries of different variations of hockey, ("including a version in England, sometime prior to 1860, in which. because of the very hilly heathland area in which it was played, a rubber cube and not a ball was used,") the game became more organised and regularised.

By 1886, when an association of clubs was formed and the game became more standardised, the modern game as we know it began (and a white painted cricket ball had become the standard object to play with). The game had also by this time divided into various branches which developed as separate sports. Shinty, a game popular in Scotland, uses both sides of a round stick with a curved end, which is shaped in a similar way to a walking stick; the Irish game, hurley, uses both sides of a stick which is flat on both sides and shaped somewhat like bill-hook with an axe-like handle. The stick in England, possibly because of the close association with it of cricket players, developed with a stick with just one flat playing side, the left face, below a round grip area - with the use of the right-face side, which is rounded, prohibited - an oddity that had a profound effect on the later development of the hockey stick and of the game itself.

Initially there were six rule requirements applying to the hockey stick.

* The stick had to be flat on the playing side (the left side when the 'toe' of the stick-head is facing away from the user).
* It had to able to be passed completely through a two inch (internal diameter) ring.
* The stick was to be smooth (no rough or sharp edges).
* The head of the stick was to be a) curved and b) made from wood.
* A maximum and minimum weight were specified, 28oz and 12oz respectively.

Description

By Rule a hockey stick comprises two parts "(even if all one piece)" A 'Head' and a 'Handle'. Historically the stick was made in two separate parts and the Head was spliced to the Handle, in much the same way as the handle of a cricket bat is spliced to the blade.

Today many hockey sticks are manufactured from man-made materials (so called 'composite sticks') in moulds and in one operation, so do not have a separate joined head and handle. By Rule the ‘head’ part was from the bottom end of the splice with the stick-handle to the base of the curve of the stickhead and the handle was from the bottom of the splice with stickhead to the top of the stick (where it was gripped in play). The need to inspect that a stick complied with new regulations, concerning materials used (Rules 1992), and with new regulations, concerning the permitted shape of the ‘head’ and handle (Rules 1990) (without rendering the stick thereafter unusable) led to a change in the description of the ‘head’ and handle parts (Rules 2004). This article will examine the transition from the shape of sticks in the era before the First World War to the Hockey World Cup in Willesden England in 1986 and from there, to the modern designs. Many of these changes have come about because of the availability of new materials and changes to playing surfaces but this article will be focused more on the reasons for stick shapes and the differences between them, rather than on an exploration of construction materials and reinforcements or ‘artificial’ playing surfaces.

Hockey stick head parts were commonly made from large timbers, 4¼" x 4¼" in section and more than 4' in length, which were bent in presses after steam treatment, dried and then cut into four 'bats' for later shaping with saw and adze. This type of manufacture is still in use today, although significant numbers of stickheads are now of laminated timber manufacture and more and more hockey sticks are now being made entirely from 'composite' materials, in one piece, in moulds.

Head length

In the upper left corner of the picture of the press there is a small insert showing the kind of head bend these presses were originally designed to produce. That stick is circa 1962/3. Near the lower right of the picture and unfortunately, cut off, is a view of the typical 'horseshoe' shape bending produced by the machine. A heavy cast iron staple was hammered across the ends while (while the timber is still in the press) and the piece was further restrained by a flexible steel strap, then removed from the press and allowed to dry out and 'set' for a few days before cutting "(It is the steel strap that causes the black stain so often seen on the base of the head of 'one piece' hockey sticks, it is caused by a reaction between the acids in the timber and the oxidising of the strap)". This particular machine was modified to run from an electric motor, but it was originally hand operated and probably dates from a time before electricity was available (or reliable) in that part of Pakistan (Sialkot - an industrial town in the province of Punjab). The boss in the centre would also have been modified to produce the tighter head bends required at the time this photograph was taken (February 1989)

The first major developments to what was later termed the 'English style' stick (and the method of play with such sticks) occurred in India. "(The game in its modern form was apparently brought to India by the British Army, although there does not appear to be any specific evidence of this. But certainly hockey was played by the British forces in India)." At that time the stickhead was very long (in excess of 12" - 300mm) and made from an indigenous British timber, ash. The Indians then produced sticks with a much shorter head length and a tighter heel bend and used mulberry, which is tougher than ash, but has similar bending characteristics and weight and is easy to work. This development changed the nature of the game, led to the 'Indian dribble' and to Indian dominance of the game in the first half of the twentieth century.

A hockey stick is occasionally used in the vertical position shown, but manipulating the movement and the direction of the ball in a controlled way (dribbling) is carried out in what is termed a 'dribbling crouch', when the handle of the stick will usually be angled between 35° and 55°. Hitting or pushing the ball can be done with the stick at any angle between the vertical and horizontal and recent changes to the rules allow even the edges of the stick to be used to sweep or strike at the ball on the ground. The various designs will be initially looked at with the handle at an angle of 45° to compare how they differ in the carrying out of the 'Indian dribble' i.e. controlling the direction of the ball by rotating the stickhead over the top/front of the ball rather than (or as well as) around the back of the ball (the English style dribble).The multi-layered stickhead diagram gives an idea of the changes in head lengths and shapes that occurred over a period of thirty years or so. It is intended to conduct an examination of some of these various head shapes with regard to the way they affect playing style and the method of using a hockey stick.

The first questions are:- Why was the stick-head shortened, surely that reduced the stopping area of the head? The answer lies in the fact that by Rule only one side of the stickhead could be used (at that time the ball could not be played with the 'edges' of the head or handle but with the flat side -or face side- only).

Using extreme examples is useful as a means of demonstrating effects that occur in less extreme configurations but are much more difficult to spot and therefore to explain. The first observation is an easy one. Top left. If the stick head is rotated onto the reverse (lighter colour) the Toe is not going to disappear into the ground to enable the reverse side of the stick to be presented to the ball - a vertical adjustment is necessary. Secondly, (top right) if the handle of the stick is kept at exactly the same angle and rotated, a horizontal adjustment is necessary to bring the reversed head to a position where contact will be made with the ball. The third figure (bottom left) shows these adjustments having been made (and a change to the angle of the handle because the position of the hand holding the stick at the top would be about the same as it is when gripping the stick in the forehand position), but the area of stickhead making contact with the ball is very small; so control may not be adequate. The fourth figure (bottom right) demonstrates that to get good contact with the ball on a larger area of the reversed head, it is necessary to move the handle much nearer to the vertical. This means the player must bring the ball in very close to the feet and come to a more upright dribbling position - this in turn impairs the ability to scan the pitch and keep the ball in peripheral vision at the same time - a considerable disadvantage when dribbling to evade opponents.

So, although the long head stick was an adequate shape for a dribbling style which was based on moving the ball forward from directly behind the ball; and changes of direction could be achieved by rotating the stick around the back of the ball and/or moving the feet to either side of the ball, it was not so easy to use the long stickhead to bring the ball across the feet and back again, particularly when it was placed wide to the left of the feet of the player. "(This left side position was compounded in difficulty with a very severe interpretation of ‘obstruction’, which prohibited shielding of the ball from an opponent. The game was also, at the time, seen as 'right-sided' and positioning the body between the ball and a close or closing opponent, approaching from the right hand side, was not allowed.)" Reversed stick hitting, pushing and flicking would be short range skills and difficult to do accurately, if at all, especially when moving at speed.

‎ Gradually over many years stickheads were made shorter and the 'heel' was made to a tighter bend. This process continued until the 'one piece' head could not be made to a sharper bend without the timber splitting out on the base. As it was, attempts to have the grain follow entirely the same curve as the bend, as it should for maximum strength "(this is why the timber is bent rather than cut to shape)" were abandoned by some producers and an upturn to the 'toe' was sometimes achieved by cutting across the wood-grain at the ‘toe’ end of the ‘head’ to achieve the desired shape. Some manufacturers resorted to gluing a separate piece of wood on top of the 'toe' or glued additional strips of timber to the inner edge of the handle above the head to get the effect of a tighter ‘heel’ bend."(‘Head adjustment’ frequently happened to 'update' old style stock or where unmodified presses were in use)".

Some players were cutting part of the toe off their sticks, to achieve a shorter head, and rounding the end off,"(although on the older styles this did nothing to tighten the bend to the 'heel' and often just ruined the stick)". Predictably, there were sticks produced for the 1986 World Cup with heads with a horizontal length of only 95mm. The International players to whom they were handed out, tried them and then returned them as unusable.

What was the difficulty? It was twofold: 1) The 'toe' was so short that it could not be rotated completely over the top circumference of the ball and 2) When the stickhead was played around the back of the ball it 'ran off', because there was insufficient 'run length' to the stickhead. If, for example, a player ‘propped’ the ball while moving in a dribbling crouch (putting the stickhead over the front of the ball), drew the ball back towards his feet and then took the stickhead around the back of the ball to bring it forward again, perhaps moving the ball off in another direction (a common movement), the margin for error was so small that the ball could easily slip off the stickhead. The ultra-short stickhead was to some extent based on the idea that the new artificial surfaces would lead to a style of hockey based on stopping the ball with the handle of the stick near horizontal to the ground and that dribbling to elude opponents would be almost eliminated with near continuous passing of the ball. Although there was a development of 'system hockey' that overcame the stick/ball skill deficiencies of the Europeans compared with India and Pakistan at the time, it was not as fluid as the kind of one and two touch passing game common in soccer and that 'ideal' was (and still is) a long way off.

Heel bend

It may be noted from the diagram that no matter how 'tight' the 'heel' bend, reversing the stickhead over the ball, with a ‘traditional’ style hockey stick ‘head’, always requires both a vertical and horizontal adjustment of the stickhead position. This is not anywhere near as difficult as it was with the very long head stick and this sort of adjustment will be almost sub-conscious in an experienced player. Note too, that when the shaft is held vertically, the ball is more securely stopped, when on the ground, to the 'toe' side of the shaft rather than in the middle of the shaft. Novice players frequently assume that the centre of the ball will align with the centre of the shaft when stopping the ball in this way and as a result, the ball deflects off to the 'heel' side and usually into their feet. Because of the 'heel' slope on the stickhead the 'vertical shaft' stop is actually much easier to carry out securely (when the ball is on the ground) if the handle is held at least 10° off the vertical, with the top of the handle sloped to the player's left. When the ball in the air, a little off the ground, below knee height for example, is often easier to 'catch' the ball correctly if the handle is vertical.

The Hook

In 1982 a Dutch inventor, Toon Coolen, patented a hockey stick with a 'hook' head. The hockey stick manufacturers Grays took the design up in 1983 and the first mass-produced hockey sticks, with laminated timber ‘head’ parts, were manufactured in Pakistan. This new design was possible because of the development of epoxy resin glues that did not require perfectly dry timber for bonding and curing to a strength that could cope with the immense stresses placed on a stickhead when a hockey ball is struck with it.

By 1993 the 'Hook' Patent, had been ruled "(following a court case in Germany)" to protect only hook shapes within 20° of the vaguely written "nearly 180°" "(referring to the degree of upturn of the 'toe' in relation to the shaft of the stick in the Patent Description; the 'shaft' of the handle being described a being bent through "nearly 180°" to form the hook shape of the stickhead)". That opened the way for the appearance of more 'J' shaped stickheads and the gradual 'morphing' of the 'midi' shape with the 'hook' shape. In that year also a Patent Application, lodged in Pakistan in 1987 by Martin Conlon, for a kinked shaft hockey stick, with a set-back Head (which was also hook shaped, but not to "near 180°"), was granted after strong opposition in Pakistan. (Indian and GB Patents had been granted in 1988, although the same company had also opposed the GB Patent Application). Mr Conlon designed and imported to the UK the first 'J' head sticks in 1990 but, prior to the 1993 decision, other distributors and manufacturers had been very reluctant to order made or produce hook style sticks of any sort, because of uncertainty about the strength of the Patent that 'ring-fenced' the 'Hook' hockey stick.

The modern hook

In the mid-90s the 'hook' head style hockey stick was relaunched, this time by the former German U21 International player Thomas Kille. Bright colours, bold graphics and painted heads were introduced. Manufacturers became much more aware of the 'look' of their products and hockey sticks sold, particularly to new players, as much on colour and 'fashion' as strength and usability.

Today, across many brands, there is a choice of angle of hook upturn, 45°, 60°, 75°. A style of stick that almost no-one in Europe wanted to use in 1987, is today used almost universally; it is difficult now to find a player who is not using a hook style hockey stick and many of them have never used the 'shortie' style at all - just as many of the players of today have never played hockey on a natural grass pitch - the development of artificial surfaces has also had a significant effect on the ways in which hockey sticks are used.

The original version, the 'Hook' relied on a Patent Description that put the inner side edge of the 'toe' parallel (or nearly so) to the facing edge of the handle. The vertical height of the 'toe' was approximately 80mm (dotted line) Fig.1 and it was of almost uniform thickness with the remainder of the stickhead.

Early modification Fig.1. reduced the horizontal head length to approximate 115mm and the 'toe height' to approximately 75mm. A hockey ball is between about 71mm and 75mm in diameter (224mm - 235mm in circumference) - so that put the 'toe height' at the same height as the maximum height of the ball. This is a common feature across hook head designs today, the 'toe' generally varies in height, between the minimum and maximum height of the ball, when the handle is in a vertical position.

The next development was a hook with a 'toe' with an inner edge that sloped away from the handle by approximately 30° (a 60° angle to the ground or a 150° 'upturn'. The 'toe height' was 75mm. (Modern versions Fig.2 vary between 70mm and 75mm. in 'toe height') The horizontal length of the head was based on the length of the 'standard' one-piece short-head stick, approximately 110mm. and modern versions seem to vary between 110mm and 115mm. The mid-90s saw the introduction of the more 'open' hooks Fig.3, some at 45° and a significant increase in horizontal head length, some as much as 120mm.

New names have been coined to describe the various hook shapes but there is much confusion and overlapping of names. 'Maxi' and 'Mega' are also terms for styles of hook shape but there is no common agreement about what these terms mean outside of each 'brand' name that employs them: what one brand terms a 'midi' another calls a 'hook' but, basically, there are three types of hook. The near symmetrical 'U', a 'tight' or 'closed' toe shape, between 60° and 75° and an 'open' shape between 45°- 55°. Where the 'toe' is shorter the same toe angles are generally referred to as 'midi'

The 'midi' head

The death knell of the ultra short head was sounded in 1986, due to the introduction of the 'midi' ‘head’ shape, produced with a laminating process; although of course many players continued to use 'one piece' short head sticks for many years after that date and many thousands more of them were manufactured. The reason for the continued use of the ‘one piece’ was that the 'midi' length was similar to that of the more popular 'one piece' stickheads that had been around for the previous ten or so years. Some 'one piece' constructions were still being produced on presses on which the central 'boss' had not been modified and the 'heel' bend was 'slower' than on that of the production of the more aware manufacturers, but the more 'go ahead' manufacturers were producing a 'one piece' that could compete well with the laminated 'midi' – at least as far as ‘playing functionality’ was concerned.

culture of the short-head stick and for a number of years after the 'midi' was introduced the 'Hook' was seen as something of a novelty, even as an indoor stick or a stick exclusively for goalkeepers. In fact versions of it were produced specifically for goalkeepers, with a very extended toe (6" - 150mm or more) and that development continued until some were made with the 'toe' extending nearly the length of the handle and the FIH 'stepped in' and ruled that the vertical 'toe' limit was in future to be 4" - (100mm).

The 'Hook' was 124mm, measured horizontally across face of the stickhead, when the handle was held vertically; the 'midi’ was 113mm ; many 'one piece’ heads between 110mm and 115mm , and the unusable 'ultra short' 94mm. A difference of only 30mm between the head length of a stick that was considered cumbersome "(although the 'Hook' also had the height of the 'toe' causing a feeling of imbalance)" to one that was considered too short to easily play with. There were still many players playing quite happily with a stick with a head length of 7" (175mm), but players buying new sticks were now conscious of quite subtle differences in stick 'feel' and performance due to length, shape and the distribution of 'head' weight - not just the total ounce weight and the 'swing weight or balance' of the stick - and for the first time, in the years after 1986, were being offered a wide range of hockey sticks from a greatly increased number of manufacturers, from which to choose what suited them. After the arrival of the laminations, some brands were offering as many as ten different shapes or styles of stickhead on the traditional shaft. The arrival of 'composites' would complicate the picture further.

In the early 1990s there were an astonishing number and variety of hockey sticks on offer compared with what had been available ten years earlier. By 1992, hockey stick reinforcement was a big issue and 'composites' had been accepted into an (extended) FIH 'experimental trial period'(there was a great deal of concern about the power generated by these new reinforcements and the safety of players). There were also hockey sticks with metal handles and inserted ply-wood heads (made by the American company Eastons, better known for making baseball bats), as well as the wide range of 'one piece' head sticks still produced and an expanding range of laminated 'midi' and laminated 'shorties'. The metal handled sticks were later banned for 'safety reasons', in what was widely regarded as a 'political' move by the FIH.

et-back stickheads

The big headed 'Hook' also suffered for a short time from the appearance at the 1986 World Cup of the first sticks with set-back heads. There wasn't a significant impact but it (and others) added to the general confusion, as apparently 'everyone and his dog' were presenting new ideas in head shape. (Metal handled and fully composite sticks had not yet made an appearance so at the time the 'battle' was about head shape and length rather than materials and to a lesser extent, because hockey players at the time tended to be more 'traditionalist', the head/handle configuration. Even reinforcement with fiberglass and carbon fibre was not the issue it was later to become.

One hockey stick produced by AREC for the French inventor, Jean Capét, had the centre of the handle aligned with the centre of the horizontal length of the head. There was a lot of promotion based on 'rotational balance' and the 'sweet spot' and 'power hitting'. The 'Hook' certainly felt out of rotational balance, especially to those who had been playing with short-head sticks that had been made with a very thin 'toe', so as to concentrate the weight of the head closer to the shaft.

Kinked-shaft & Recurve heads.

The traditional small arc to the heel edge of the hockey stick had the effect of setting the stick-head back slightly. This aspect of stick design (of which the AREC hockey stick was an extreme example) was first explored just prior to the Men's Hockey World Cup of 1986 and resulted in the production of hockey sticks with a stick-head considerably more set-back in relation to the handle. The original design, aligning the centre line of the handle with the centre of the ball, in the common striking position, featured a counterbalancing 'kink' or protrusion to the handle on the 'toe' edge of the handle, just above the head of the stick. This invention of the 'kinked-shaft' and set-back head stick led directly to rules governing the amount of bend or 'permitted deviation' to the 'edge sides' of the hockey stick handle. Some of these were later termed 'recurve' heads (a description given to a later style, produced by an Australian manufacturer, without the patented 'kink' feature.)

Permitted 'deviation'

To describe the dimensions of Head and Handle the hockey stick is envisaged to be placed with the bottom curve of the stickhead on a level surface, the x-axis, with the stick -handle perpendicular to it (the y-axis). The y-axis runs from an intersection with the x-axis (0) vertically through the midpoint of the top of the handle. The Head is the part from the x-axis to the line C-C (diagram) a vertical distance of 100mm. This line C-C also describes the limit on any upturn to the 'toe' of the Head. By Rule there is no limit to the length of the stick-head along the x-axis, but practical considerations, as well as technicalities related to the joining of the Head and the Handle (on the line C-C), do create limitations.

The extent of the stick-head along the X+ axis, towards the 'heel' of the Head is confined by the rule requirement that the stick-head and the handle meet in a smooth continuous fashion at the line C-C and by a rule restriction on the shape of the handle, which is that the stick-handle must not project beyond the line B1-B1. It is possible to envisage a stick where the width of handle did not extend beyond the line A1-A1, thus allowing a significant extension of the stick-head along the X+ axis, but the practicalities of such a design seem to be limited and have not been explored. The length of the Head (or 'toe') along the X- axis has varied enormously, especially since the Second World War and again after the introduction of the timber lamination process in the early 1980s.

The stick handle may be bent or 'deviated', in a smooth curve only, once only to either side. That is the handle may have one outmoving curve on the 'heel' side of the head and one outmoving curve on the 'toe' side. It is therefore possible to have a hockey stick with a handle deviation to the front or 'toe' side or a handle deviation to the back or 'heel' side or a stick-handle that is bent once to both the 'toe' and 'heel' sides.

The maximum permitted width of the handle (51mm) is illustrated in the diagram by the distance between the dotted lines A-A and A1-A1. A hockey stick handle will rarely be of the maximum permitted width: most are between 46mm and 48mm at the widest point.

The maximum permitted 'deviation' is shown by the lines B-B and B1-B1 respectively. The line B-B is 20mm further along the X- axis than the line A-A and the line B1-B1 is 20mm further along the X+ axis than the line A1-A1. There is no limit along the y-axis specified, so the deviation curve or curves may be of any length along the length of the stick-handle and some goalkeeping sticks have an outward curve on the 'toe' side that extends for almost half the total length of the stick.

Permitted bow

Increasing the degree of bow to the 'face' side (flat side) makes it easier to get high speeds from the drag-flick (a 'sling-shot' style stroke started from behind the body of the flicker) and allows easier execution of the stroke. At first, after extreme bows where introduced (2005), the Hockey Rules Board (HRB) placed a limit of 50mm on the maximum depth of such a bow over the length of the stick, but experience quickly demonstrated this degree of bend to be excessive.

The Rules of Hockey 2006 limited this particular curve of the stick to 25mm so as to limit the power with which the ball can be flicked and to try to ensure that hitting control was maintained (the curvature to the face of the stick considerably influences the angle at which the stick-head strikes through the ball). The placement of the maximum bow along the length of the handle has not, however been specified, so the angle at which the stick head is presented to the ball (and hence the facility to lift the ball easily) will vary (as will the propensity to lift the ball accidentally when hitting it). It is now illegal for any hockey stick to have a bow that exceeds 25 mm. The bow height is measured by placing the stick face-side to a flat surface and presenting the official measuring device, a 25mm high metal triangular or cylindrical measure, to the gap between the surface and the under-flat of the stick.

Since this article was first written there have been attempts to get around the rule by the production of a stick which 'in a natural resting position' has a face side that is not parallel to the flat surface measured from but rests with the face at a sharp angle. The result of the sloping of the face side is to put one edge of it closer than 25mm to the flat surface and permits a much deeper bow than would otherwise be possible. This obviously flouts the intention of the rule, so it is possible that there may be a move to a measuring cylinder, under and across, the entire face of the stick.There has also been a development in design called the 'low bow'. This places the maximum bow of the stick much closer to the head than was previously the case, when it was positioned more centrally on the length of the stick. The effect of placing the maximum bow lower down the handle has been to increase the angle at which the stick head is presented to the ball. The angle of presentation of a '25mm low bow' is approximately the same as was achieved when the maximum permitted bow was 50mm but the maximum was situated at about the mid-length of the stick.

tages of Development

The development of the modern hockey stick has not taken place in one continuous flow with each development following on from a previous one. Many things changed in the same time frame but at different speeds, especially some of the later developments. There have been more changes in stick design in the last twenty-five years than there were in the previous one hundred and twenty-five and the pace of change has been an ever increasing one. There will no doubt be further development, probably in materials, possibly because of changes to the rules. In roughly chronological order this is what has happened so far.

1860's Hockey taken to India. Stickhead made shorter; move from Ash to Mulberry timber for the stick head.

Further shortening of stickhead; heel of head made tighter. Taken as far as possible by 1986, when a move back towards a midi length began.

1960's Reinforcement with fiberglass.

1970's Reinforcement with carbon and aramid as well as glass fibres.

1980's Stick-heads made from glued lamination of wood in addition to the one piece heads

1982 Introduction of upturned toe, first the Hook closely followed by Midi and 'J' shaped designs.

1980's Limit placed on upturn of 'toe' of head at 100mm.

1986 Kinked shaft stick. Set back stick head.

1980's Stick lengths other than 36", up to 39", become widely available and custom lengths 42"+ can be purchased.

1990 Permitted deviation rule - limited bends to edges of stick handle defined.

1990 Specialist goalkeeper's sticks introduced. The first being the ZigZag Save.

1980's Metal handled stick with a inserted wooden head (plywood)introduced.

1994 Composite sticks fully accepted in rules after a two year 'experiment'.

1990's Metal handles banned.

2004 Rule redefining of head and handle. Head the part from the base of the curve perpendicular to 100mm - handle the remainder of the stick.

2000's Refinement of head shapes, probably five shapes available as 'standard'.

2000's Number of wood core sticks in use declines as moulded 'composites' become the norm.

2006 Bow of the face of the handle is increased to facilitate drag-flicking. Closely followed by a rule concerning maximum permitted bow.

2007 Low bow sticks introduced.

The forehand striking position

For the purposes of this article the ball will be assumed to be 73mm in diameter. Ball size does play a significant part in stickwork and ball control (as does the weight and hardness of the ball) but an investigation of these is outside the scope of this article. The width of stick handles does vary (as does the horizontal length of stickheads) but for clarity and convenience the shaft of the handle just above the head has been taken as 46mm, which is fairly common, and the sticks scaled from that measurement.

The position of the ball when it is played, particularly hit with the stickhead, does, however have a bearing on stickhead design. Using just one of the whole range of angles the ball may be struck at from the forehand (right-hand) side (45°), the position of the ball will be looked at in relation to both the centre of the head of the stick and a line projected to run through the centre of the handle. An examination on the position of wear on the base of stickheads that have been used over a period on an abrasive playing surface lead to the conclusion that the ball is positioned close to the center of the head length of the modern stick. This is also the more usual position for receiving or stopping the ball in play while in the 'dribbling crouch'. Obviously when the handle is vertical or horizontal there is considerable variation but in most common hitting and dribbling positions the line of the uppermost edge of the handle projects close to the centre of the ball.

One of the problems with a striking head that is significantly narrower than the diameter of the ball is that the ball is easily lifted unintentionally if struck with the face of the stickhead inclined backward, 'open', rather than vertical or nearly so. Striking the ball with a 'closed' face is not always a solution, because it is then possible to 'squeeze' or 'clip' it, again causing the ball to rise, possibly even more steeply than with the so called 'undercut' hit.

Another difficulty is striking the ball accurately at the point on the stickhead that is intended (the usual range of error can be seen, in the diagram, in the difference of the lengths of the red lines that run from the centre of the two differently positioned stickheads).

It is also necessary to avoid unintentionally turning the handle during a hit at the ball so that the ball is 'sliced' (to the right) or hooked (to the left), this is achieved by gripping the stick firmly, generally with one hand locked against the other at the top of the handle, at the moment of impact with the ball.

Ensuring vertical and flat (perpendicular to intended direction of ball travel) contact with the ball is in the hands of the player and the coach, but achieving a correct contact position between the stickhead and the ball can be helped by the design of the stick.

At a common playing angle three different styles of hook stickhead present identical ball/handle relationships because the bend of the 'heel' is the same in each stick. An increase in the height of the 'toe' over the ball is very noticeable and is most pronounced in the more 'open' shape. The modern hook does not suffer from the effects of a rotational imbalance in the head as much as the original did because stickheads are now generally tapered towards the 'toe', rather than of uniform thickness so 'toe' height is not, from a weight and rotational balance point of view, as much of an issue as it once might have been. The stickhead is also generally tapered from the mid-point of the striking area towards the bottom curve, so when the stick is in the reversed position the maximum thickness of the head is not at the highest point. This gives a more balanced rotation of the weight of the stickhead over the ball.

Some of the early hooks were actually thinner in the centre and became thicker in the 'toe'; it is likely that this was done to facilitate more powerful reversed-stick hitting of the ball but it gave the stick unusual handling characteristics when turning it over the ball and back in 'stickwork': an 'overturning' or 'throw' of the stickhead had to be taken into account. The 'composite' stick is generally lighter than the previous wood versions and it is unusual these days to find a young player using the 25oz - 26oz sticks that were quite commonly used on grass in the 1970s, especially by those likely to be regularly taking hits at a stationary ball.


Wikimedia Foundation. 2010.

Игры ⚽ Нужен реферат?

Look at other dictionaries:

  • Hockey stick (disambiguation) — A hockey stick is a piece of equipment used in field hockey, ice hockey, or roller hockey to move the ball or puck.Hockey stick may also refer to:In sports: * Field hockey stick * Ice hockey stick * Golden Hockey Stick (Czechoslovakia), an award… …   Wikipedia

  • Field hockey — sport imagesize=300px caption=A game of field hockey in progress union=International Hockey Federation nickname=Hockey first=19th century registered= clubs= contact=Yes team=11 players mgender= category=Indoor/Outdoor ball=Hockey ball… …   Wikipedia

  • field hockey — a game played on a rectangular field having a netted goal at each end, in which two teams of 11 players each compete in driving a small leather covered ball into the other s goal, each player being equipped with a stick having a curved end or… …   Universalium

  • Hockey stick — A hockey stick is a piece of equipment used in field hockey, ice hockey, or roller hockey to move the ball or puck. Field hockey Field hockey sticks have an end which varies in shape, often depending on the players position. In general there are… …   Wikipedia

  • field hockey — noun a game resembling ice hockey that is played on an open field; two opposing teams use curved sticks try to drive a ball into the opponents net • Syn: ↑hockey • Members of this Topic: ↑goalmouth, ↑net, ↑stick, ↑winger • Hypernyms: ↑ …   Useful english dictionary

  • hockey stick — noun sports implement consisting of a stick used by hockey players to move the puck • Hypernyms: ↑stick * * * noun : a curved or angled stick used in playing hockey * * * the stick used in field hockey or ice hockey. [1840 50] * * * hockey stick …   Useful english dictionary

  • hockey stick — noun a) A stick used to handle the puck in ice hockey, having a flat, angled blade at the end. b) A stick used to handle the ball in field hockey, having a flat faced hook at the end …   Wiktionary

  • hockey stick — hock′ey stick n. spo the long, hooked stick used in field hockey or ice hockey • Etymology: 1840–50 …   From formal English to slang

  • hockey stick — the stick used in field hockey or ice hockey. [1840 50] * * * …   Universalium

  • field hockey — noun Date: 1903 a game played on a turfed field between two teams of 11 players each whose object is to direct a ball into the opponent s goal with a hockey stick …   New Collegiate Dictionary

Share the article and excerpts

Direct link
Do a right-click on the link above
and select “Copy Link”