﻿

The ISO metric screw threads are the world-wide most commonly used type of general-purpose screw thread.[1] They were one of the first international standards agreed when the International Organization for Standardization was set up in 1947.[citation needed]

## Basic profile

Basic profile of all ISO metric screw threads

The design principles of ISO general-purpose metric screw threads ("M" series threads) are defined in international standard ISO 68-1.[2] Each thread is characterized by its major diameter D and its pitch P. ISO metric threads consist of a symmetric V-shaped thread. In the plane of the thread axis, the flanks of the V have an angle of 60° to each other. The outermost 1/8 and the innermost 1/4 of the height H of the V-shape are cut off from the profile.

The relationship between the height H and the pitch P is found using the following equation:[3]

$H = \cos(30^\circ) \cdot P = \frac{ {\sqrt 3}}{2} \cdot P \approx 0.866 \cdot P$

In an external (male) thread (e.g., on a bolt), the major diameter Dmaj and the minor diameter Dmin define maximum dimensions of the thread. This means that the external thread must end flat at Dmaj, but can be rounded out below the minor diameter Dmin. Conversely, in an internal (female) thread (e.g., in a nut), the major and minor diameters are minimum dimensions, therefore the thread profile must end flat at Dmin but may be rounded out beyond Dmaj.

The minor diameter Dmin and effective pitch diameter Dp are derived from the major diameter and pitch as

$D_\mathrm{min} = D_\mathrm{maj} - 2\cdot\frac58\cdot H = D_\mathrm{maj} - \frac{ 5 {\sqrt 3}}{8}\cdot P \approx D_\mathrm{maj} - 1.082532 \cdot P$
$D_\mathrm{p} = D_\mathrm{maj} - 2\cdot\frac38\cdot H = D_\mathrm{maj} - \frac{ 3 {\sqrt 3}}{8}\cdot P \approx D_\mathrm{maj} - 0.649519 \cdot P$

## Designation

A metric ISO screw thread is designated by the letter M followed by the value of the nominal diameter D (Dmaj in the diagram above) and the pitch P, both expressed in millimetres and separated by the multiplication sign, × (e.g., M8×1.25). If the pitch is the normally used "coarse" pitch listed in ISO 261 or ISO 262, it can be omitted (e.g., M8). Tolerance classes defined in ISO 965-1 can be appended to these designations, if required (e.g., M500– 6g in external threads). External threads are designated by lowercase letter, g or h. Internal threads are designated by upper case letters, H or G.

## Preferred sizes

ISO 261 specifies a detailed list of preferred combinations of outer diameter D and pitch P for ISO metric screw threads.[4]

ISO 262 specifies a shorter list of thread dimensions – a subset of ISO 261.[5]

Nominal diameter
D (mm)
ISO 261
Pitch
P (mm)
1st
choice
ISO 262
2nd
choice
coarse fine
1 0.25
1.2 0.25
1.4 0.3
1.6 0.35
1.8 0.35
2 0.4
2.5 0.45
3 0.5
3.5 0.6
4 0.7
5 0.8
6 1
7 1
8 1.25 1
10 1.5 1.25 or 1
12 1.75 1.5 or 1.25
14 2 1.5
Nominal diameter
D (mm)
Pitch
P (mm)
1st
choice
2nd
choice
coarse fine
16 2 1.5
18 2.5 2 or 1.5
20 2.5 2 or 1.5
22 2.5 2 or 1.5
24 3 2
27 3 2
30 3.5 2
33 3.5 2
36 4 3
39 4 3
42 4.5 3
45 4.5 3
48 5 3
52 5 4
56 5.5 4
60 5.5 4
64 6 4

The "coarse" pitch is the commonly-used default pitch for a given diameter. In addition, one or two smaller "fine" pitches are defined, for use in applications where the height of the normal "coarse" pitch would be unsuitable (e.g., threads in thin-walled pipes). The terms "coarse" and "fine" have (in this context) no relation to the manufacturing quality of the thread.

In addition to coarse and fine threads, there is another division of extra fine, or "superfine" threads, with a very fine pitch thread. Superfine pitch metric threads are occasionally used in automotive components, such as suspension struts, and are commonly used in the aviation manufacturing industry.

## Standards

### International

• ISO 68-1: ISO general purpose screw threads — Basic profile — Metric screw threads.
• ISO 261: ISO general purpose metric screw threads — General plan.
• ISO 262: ISO general purpose metric screw threads — Selected sizes for screws, bolts and nuts.
• ISO 965: ISO general purpose metric screw threads — Tolerances[6]
• ISO 965-1: Principles and basic data
• ISO 965-2: Limits of sizes for general purpose external and internal screw threads.
• ISO 965-3: Deviations for constructional screw threads
• ISO 965-4: Limits of sizes for hot-dip galvanized external screw threads to mate with internal screw threads tapped with tolerance position H or G after galvanizing
• ISO 965-5: Limits of sizes for internal screw threads to mate with hot-dip galvanized external screw threads with maximum size of tolerance position h before galvanizing

## References

1. ^ ISO/TC/ 1 Business Plan, 2007-03-05, Version 1.3. Table 3: The market share of each screw thread, p. 7.
2. ^ ISO 68-1:1998 ISO general purpose screw threads – Basic profile – Part 1: Metric screw threads. International Organization for Standardization.
3. ^ Oberg et al. 2000, p. 1706.
4. ^ ISO 261:1998 ISO general purpose metric screw threads – General plan. International Organization for Standardization. 17 Dec 1998.
5. ^ ISO 262:1998 ISO general purpose metric screw threads – Selected sizes for screws, bolts and nuts. International Organization for Standardization. 17 Dec 1998.
6. ^ [1] ISO 965 in the Catalogue on the Official ISO website

### Bibliography

• Oberg, Erik; Jones, Franklin D.; Horton, Holbrook L.; Ryffel, Henry H. (2000), Machinery's Handbook (26th ed.), New York: Industrial Press Inc., ISBN 0-8311-2635-3.

Wikimedia Foundation. 2010.

### Look at other dictionaries:

• Screw thread — Internal and external threads illustrated using a common nut and bolt. The screw and nut pair can be used to convert torque into linear force. As the screw (or bolt) is rotated, the screw moves along its axis through the fixed nut, or the non… …   Wikipedia

• Screw — This article is about the fastener. For other uses, see Screw (disambiguation). Screws come in a variety of shapes and sizes for different purposes. U.S. quarter coin (diameter 24 mm) shown for scale. A screw, or bolt, is a type of fastener… …   Wikipedia

• Thread pitch gauge — Threading gauges, pictured on the right, are also referred to as pitch gauges and are used to measure the pitch or lead of screw threads. The uppermost gauge in the image is an ISO metric pitch gauge, the larger gauge in the center is for… …   Wikipedia

• Unified Thread Standard — Threads per inch redirects here. For the textile term, see Glossary of textile manufacturing#T. The Unified Thread Standard (UTS) defines a standard thread form and series along with allowances, tolerances, and designations for screw threads… …   Wikipedia

• List of ISO standards — This is a list of ISO standards that are discussed in Wikipedia articles. For a list of all the more than 16,000 ISO standards (as of 2007), see the [http://www.iso.org/iso/en/CatalogueListPage.CatalogueList ISO Catalogue] .About 300 of the… …   Wikipedia

• British Association screw threads — British Association or BA screw threads are a largely obsolete set of small screw threads, the largest being 0BA at 6 mm diameter. They were, and to some extent still are, used for miniature instruments and modelling.They are unusual in that they …   Wikipedia

• British standard pipe thread — The British Standard Pipe thread (BSP thread) is a family of standard screw thread types that has been adopted internationally for interconnecting and sealing pipe ends by mating an external (male) with an internal (female) thread.TypesTwo types… …   Wikipedia

• British Standard Whitworth — (BSW) is one of a number of imperial unit based screw thread standards which use the same bolt heads and nut hexagonal sizes, some others being British Standard Fine thread (BSF) and British Standard Cycle. These three are collectively called… …   Wikipedia

• Computer case screws — From left to right: a 6 32 thumbscrew, a 6 32 screw, an M3 screw, and a self tapping screw for case fans Computer case screws are the hardware used to fasten together parts of a computer case and to fasten the system components (such as… …   Wikipedia

• Drill and tap size chart — Below is a comprehensive drill and tap size chart for all drills, imperial and metric, and taps up to 36.5 mm. Contents 1 Chart 2 See also 3 References 4 External links …   Wikipedia