Tool steel

Tool steel

Tool steel refers to a variety of carbon and alloy steels that are particularly well-suited to be made into tools. Their suitability comes from their distinctive hardness, resistance to abrasion, their ability to hold a cutting edge, and/or their resistance to deformation at elevated temperatures (red-hardness). Tool steel is generally used in a heat-treated state.

With a carbon content between 0.7% and 1.5%, tool steels are manufactured under carefully controlled conditions to produce the required quality. The manganese content is often kept low to minimize the possibility of cracking during water quenching. However, proper heat treating of these steels is important for adequate performance, and there are many suppliers who provide tooling blanks intended for oil quenching.

Tool steels are made to a number of grades for different applications. Choice of grade depends on, among other things, whether a keen cutting edge is necessary, as in stamping dies, or whether the tool has to withstand impact loading and service conditions encountered with such hand tools as axes, pickaxes, and quarrying implements. In general, the edge temperature under expected use is an important determinant of both composition and required heat treatment. The higher carbon grades are typically used for such applications as stamping dies, metal cutting tools, etc.

Tool steels are also used for special applications like injection molding because the resistance to abrasion is an important criterion for a mold that will be used to produce hundreds of thousands of parts.

The AISI-SAE grades of tool steel is the most common scale used to identify various grades of tool steel. Individual alloys within a grade are given a number; for example: A2, O1, etc.

Contents

Water-hardening grades

W-grade tool steel gets its name from its defining property of having to be water quenched. W-grade steel is essentially high carbon plain-carbon steel. This type of tool steel is the most commonly used tool steel because of its low cost compared to other tool steels. They work well for small parts and applications where high temperatures are not encountered; above 150 °C (302 °F) it begins to soften to a noticeable degree. Hardenability is low so W-grade tool steels must be quenched in water. These steels can attain high hardness (above HRC 60) and are rather brittle compared to other tool steels.

The toughness of W-grade tool steels are increased by alloying with manganese, silicon and molybdenum. Up to 0.20% of vanadium is used to retain fine grain sizes during heat treating.

Typical applications for various carbon compositions are:

  • 0.60–0.75% carbon: machine parts, chisels, setscrews; properties include medium hardness with good toughness and shock resistance.
  • 0.76–0.90% carbon: forging dies, hammers, and sledges.
  • 0.91–1.10% carbon: general purpose tooling applications that require a good balance of wear resistance and toughness, such as drills, cutters, and shear blades.
  • 1.11–1.30% carbon: small drills, lathe tools, razor blades, and other light-duty applications where extreme hardness is required without great toughness.

Cold-working grades

These tool steels are used on larger parts or parts that require minimal distortion during hardening. The use of oil quenching and air hardening helps reducing distortion as opposed to higher stress caused by quicker water quenching. More alloying elements are used in these steels, as compared to water-hardening grades. These alloys increase the steels' hardenability, and thus require a less severe quenching process. These steels are also less likely to crack and are often used to make knife blades.

Oil-hardening grades

O-1 contains 0.90% carbon 1.0–1.4% manganese, 0.50% chromium, 0.50% nickel, and 0.50% tungsten. It is a very good cold work steel and also makes very good knives. It can be hardened to about 57-61 HRC.

Air-hardening grades

The first air hardening grade tool steel was mushet steel, which was known as air-hardening steel at the time.

Modern air-hardening steels are characterized by low distortion during heat treatment because of their high-chromium content. They also harden in air because they have less alloyants than oil-hardening grades. Their machinability is good for tool steels and they have a balance of wear resistance and toughness (i.e. between the D- and shock-resistant grades).[1]

Grade Composition Notes
A-2[2] 1.0% C, 1.0% Mn, 5.0% Cr, 0.3% Ni, 1.0% Mo, 0.15–0.50% V A common general purpose tool steel; it is the most commonly used variety of air-hardening steel. It is commonly used for blanking and forming punches, trimming dies, thread rolling dies, and injection molding dies.[1]
A-3[3] 1.25% C, 0.5% Mn, 5.0% Cr, 0.3% Ni, 0.9–1.4% Mo, 0.8–1.4% V
A-4[4] 1.0% C, 2.0% Mn, 1.0% Cr, 0.3% Ni, 0.9–1.4% Mo
A-6[5] 0.7% C, 1.8–2.5% Mn, 0.9–1.2% Cr, 0.3% Ni, 0.9–1.4% Mo This grade of tool steel air-hardens at a relatively low temperature (approximately the same temperature as oil-hardening grades) and is dimensionally stable. Therefore it is commonly used for dies, forming tools, and gauges that do not require extreme wear resistance but do need high stability.[1]
A-7[6] 2.00–2.85% C, 0.8% Mn, 5.00–5.75% Cr, 0.3% Ni, 0.9–1.4% Mo, 3.9–5.15% V, 0.5–1.5 W
A-8[7] 0.5–0.6% C, 0.5% Mn, 4.75–5.50% Cr, 0.3% Ni, 1.15–1.65% Mo, 1.0–1.5 W
A-9[8] 0.5% C, 0.5% Mn, 0.95–1.15% Si, 4.75–5.00% Cr, 1.25–1.75% Ni, 1.3–1.8% Mo, 0.8–1.4% V
A-10[9] 1.25–1.50% C, 1.6–2.1% Mn, 1.0–1.5% Si, 1.55–2.05% Ni, 1.25–1.75% Mo This grade contains a uniform distribution of graphite particles to increase machinability and provide self-lubricating properties. It is commonly used for gauges, arbors, shears, and punches.[10]

D-grades

D-grade tool steels contain between 10% and 18% chromium. These steels retain their hardness up to a temperature of 425 °C (797 °F). Common applications for these grade of tool steel is forging dies, die-casting die blocks, and drawing dies. Due to high chromium content, certain D-grade tool steel grades are often considered stainless or semi-stainless tool steels. However their corrosion resistance was very limited due to the precipitation of major amount of chromium and carbon as carbides.

D-2 contains 1.5% carbon and 11.0–13.0% chromium; additionally it is composed of 0.45% manganese, 0.030% max phosphorus, 0.030% max sulfur, 1.0% vanadium, 0.7% molybdenum, and 0.30% silicon. D2 is very wear resistant but not as tough as lower alloyed steels. Mechanical properties of D-2 is very sensitive to heat treatment. It is widely used for shear blades, planer blades and industrial cutting tools, sometimes used for knives.

1.2767

ISO 1.2767, also known as DIN X 45 NiCrMo 4, AISI 6F7, and BS EN 20 B, is an air hardening tool steel with a primary alloying element of nickel. It possesses good toughness, stable grains, and is highly polishable. It is primarily used for dies in plastic injection molding application that involve high stresses. Other applications include blanking dies, forging dies, and industrial blades.[11]

Shock resisting grades

S-grade tool steel are designed to resist shock at both low and high temperatures. A low carbon content is required for the necessary toughness (approximately 0.5% carbon). Carbide-forming alloys provide the necessary abrasion resistance, hardenability, and hot-working characteristics. This family of steels displays very high impact toughness and relatively low abrasion resistance, it can attain relatively high hardness (HRC 58/60). This type of steel is used in applications such as jackhammer bits.

High speed grades

T-grade and M-grade tool steels are used for cutting tools where strength and hardness must be retained at temperatures up to or exceeding 760 °C (1,400 °F). M-grade tool steels were developed to reduce the amount of tungsten and chromium required.

T1 (also known as 18-4-1) is a common T-grade alloy. Its composition is 0.7% carbon, 18% tungsten, 4% chromium, and 1% vanadium. M2 is a common M-grade alloy.

Hot-working grades

H-grade tool steels were developed for strength and hardness during prolonged exposure to elevated temperatures. All of these tool steels use a substantial amount of carbide forming alloys. H1 to H19 are based on a chromium content of 5%; H20 to H39 are based on a tungsten content of 9-18% and a chromium content of 3–4%; H40 to H59 are molybdenum based.

Special purpose grades

  • P-grade tool steel is short for plastic mold steels. They are designed to meet the requirements of zinc die casting and plastic injection molding dies.
  • L-grade tool steel is short for low alloy special purpose tool steel. L6 is extremely tough.
  • F-grade tool steel is water hardened and substantially more wear resistant than W-grade tool steel.

Comparison

AISI-SAE tool steel grades[12]
Defining property AISI-SAE grade Significant characteristics
Water-hardening W
Cold-working O Oil-hardening
A Air-hardening; medium alloy
D High carbon; high chromium
Shock resisting S
High speed T Tungsten base
M Molybdenum base
Hot-working H H1–H19: chromium base
H20–H39: tungsten base
H40–H59: molybdenum base
Plastic mold P
Special purpose L Low alloy
F Carbon tungsten

See also

  • Silver steel is a common tool steel in the UK that is roughly equivalent to drill rod in the U.S.

References

  1. ^ a b c Oberg et al. 2004, pp. 466–467.
  2. ^ AISI A2, Efunda, archived from the original on 2010-12-25, http://www.webcitation.org/5vFGMZ1wV, retrieved 2010-12-25. 
  3. ^ AISI A3, Efunda, archived from the original on 2010-12-25, http://www.webcitation.org/5vFGQq3xA, retrieved 2010-12-25. 
  4. ^ AISI A4, Efunda, archived from the original on 2010-12-25, http://www.webcitation.org/5vFGbt3Cy, retrieved 2010-12-25. 
  5. ^ AISI A6, Efunda, archived from the original on 2010-12-25, http://www.webcitation.org/5vFGon2de, retrieved 2010-12-25. 
  6. ^ AISI A7, Efunda, archived from the original on 2010-12-25, http://www.webcitation.org/5vFGw8Bhe, retrieved 2010-12-25. 
  7. ^ AISI A8, Efunda, archived from the original on 2010-12-25, http://www.webcitation.org/5vFH565FE, retrieved 2010-12-25. 
  8. ^ AISI A9, Efunda, archived from the original on 2010-12-25, http://www.webcitation.org/5vFHCCD2B, retrieved 2010-12-25. 
  9. ^ AISI A10, Efunda, archived from the original on 2010-12-25, http://www.webcitation.org/5vFHJbz8A, retrieved 2010-12-25. 
  10. ^ A-10 Tool Steel Material Information, archived from the original on 2010-12-25, http://www.webcitation.org/5vFKatMwf, retrieved 2010-12-25. 
  11. ^ Plastid Mould Steel / Cold Working Steel, archived from the original on 2010-11-27, http://www.webcitation.org/5uZ0Y1heV, retrieved 2010-11-27. 
  12. ^ Oberg et al. 2004, p. 452.

Bibliography

  • Degarmo, E. Paul; Black, J T.; Kohser, Ronald A. (2003), Materials and Processes in Manufacturing (9th ed.), Wiley, ISBN 0-471-65653-4 .
  • Oberg, Erik; Jones, Franklin D.; McCauley, Christopher J.; Heald, Ricardo M. (2004), Machinery's Handbook (27th ed.), Industrial Press, ISBN 978-0831127008. 

External links


Wikimedia Foundation. 2010.

Игры ⚽ Поможем сделать НИР

Look at other dictionaries:

  • Tool steel — Hard steel, usually crucible steel, capable of being tempered so as to be suitable for tools. [Webster 1913 Suppl.] …   The Collaborative International Dictionary of English

  • Tool steel — Tool steel. См. Инструментальная сталь. (Источник: «Металлы и сплавы. Справочник.» Под редакцией Ю.П. Солнцева; НПО Профессионал , НПО Мир и семья ; Санкт Петербург, 2003 г.) …   Словарь металлургических терминов

  • tool steel — noun alloy steel that is suitable for making tools; is hard and tough and can retain a cutting edge • Hypernyms: ↑alloy steel • Hyponyms: ↑high speed steel, ↑hot work steel * * * noun 1. : hard usually electric steel capable of being tempered so… …   Useful english dictionary

  • tool steel — įrankinis plienas statusas T sritis chemija apibrėžtis tool steel 98% Fe, 0,6–1,4% C, 0,15–0,6% Mn, tool steel 0,3% Si, 0,3% S, 0,03% P lydinys. atitikmenys: angl. chisel tool steel; tool steel rus. инструментальная сталь …   Chemijos terminų aiškinamasis žodynas

  • tool steel — instrumentinis plienas statusas T sritis chemija apibrėžtis Kietas, atsparus trinčiai plienas, naudojamas instrumentams gaminti. atitikmenys: angl. chisel steel; tool steel rus. инструментальная сталь …   Chemijos terminų aiškinamasis žodynas

  • tool steel — any of various high carbon steels capable of being hardened and tempered to meet special requirements for machining, etc. * * * Specialty steels that are produced in small quantities, contain expensive alloys, and are often sold only by the… …   Universalium

  • tool steel — /ˈtul stil/ (say toohl steel) noun any of various steels, containing up to about 1.5 per cent carbon and various alloying metals, which are suitable for use in tools for cutting metal …  

  • tool steel — Смотри инструментальная сталь …   Энциклопедический словарь по металлургии

  • tool steel — a generic term applied to a wide range of steels, both plain carbon and alloy. It includes steels suitable for various types of cutting tools, press tools, hot and cold heading dies, molds for plastics and die casting, extrusion tools, hand tools …   Mechanics glossary

  • chisel tool steel — įrankinis plienas statusas T sritis chemija apibrėžtis chisel tool steel 98% Fe, 0,6–1,4% C, 0,15–0,6% Mn, chisel tool steel 0,3% Si, 0,3% S, 0,03% P lydinys. atitikmenys: angl. chisel tool steel; tool steel rus. инструментальная сталь …   Chemijos terminų aiškinamasis žodynas

Share the article and excerpts

Direct link
Do a right-click on the link above
and select “Copy Link”