- Anaesthetic vaporiser
An anaesthetic vaporiser is a device generally attached to an
anaesthetic machinewhich delivers a given concentration of a volatile anaestheticagent.
The design of these devices takes account of varying
fresh gas flow
Historically, ether (the first volatile agent) was first used by John Snow's inhaler (1847) but was superseded by the use of
chloroform(1848). Ether then slowly made a revival (1862–1872) with regular use via Curt Schimmelbusch's "mask", a narcosismask for dripping liquid ether. Now obsolete, it was a mask constructed of wire, and covered with cloth.
Pressure and demand from
dental surgeons for a more reliable method of administrating ether helped modernise its delivery. In 1877, Clover invented an ether inhaler with a water jacket, and by the late 1899 alternatives to ether came to the fore, mainly due to the introduction of spinal anaesthesia. Subsequently this resulted in the decline of ether (1930–1956) use due to the introduction of cyclopropane, trichloroethylene, and halothane. By the 1980s, the anaesthetic vaporiser had evolved considerably; subsequent modifications lead to a raft of additional safety features such as temperature compensation, a bimetallic strip, temperature-adjusted splitting ratio and anti-spill measures.
There are generally two types of vaporisers: plenum and drawover. Both have distinct advantages and disadvantages. A third type of vaporiser is exclusively used for the agent
The plenum vaporiser is driven by
positive pressurefrom the anaesthetic machine, and is usually mounted on the machine. The performance of the vaporiser does not change regardless of whether the patient is breathing spontaneously or is mechanically ventilated. The internal resistance of the vaporiser is usually high, but because the supply pressure is constant the vaporiser can be accurately calibratedto deliver a precise concentration of volatile anaestheticvapour over a wide range of fresh gas flows. The plenum vaporiser is an elegant device which works reliably, without external power, for many hundreds of hours of continuous use, and requires very little maintenance.
The plenum vaporiser works by accurately splitting the incoming gas into two streams. One of these streams passes straight through the vaporiser in the bypass channel. The other is diverted into the vaporising chamber. Gas in the vaporising chamber becomes fully saturated with volatile anaesthetic vapour. This gas is then mixed with the gas in the bypass channel before leaving the vaporiser.
A typical volatile agent,
isoflurane, has a saturated vapour pressureof 32kPa (about 1/3 of an atmosphere). This means that the gas mixture leaving the vaporising chamber has a partial pressureof isoflurane of 32kPa. At sea-level ( atmospheric pressureis about 101kPa), this equates conveniently to a concentrationof 32%. However, the output of the vaporiser is typically set at 1-2%, which means that only a very small proportion of the fresh gas needs to be diverted through the vaporising chamber (this proportion is known as the splitting ratio). It can also be seen that a plenum vaporiser can only work one way round: if it is connected in reverse, much larger volumes of gas enter the vaporising chamber, and therefore potentially toxic or lethal concentrations of vapour may be delivered. (Technically, although the dial of the vaporiser is calibrated in volume percent (e.g. 2%), what it actually delivers is a partial pressure of anaesthetic agent (e.g. 2kPa)).
The performance of the plenum vaporiser depends extensively on the saturated vapour pressure of the volatile agent. This is unique to each agent, so it follows that each agent must only be used in its own specific vaporiser. Several safety systems, such as the Fraser-Sweatman system, have been devised so that filling a plenum vaporiser with the wrong agent is extremely difficult. A mixture of two agents in a vaporiser could result in unpredictable performance from the vaporiser.
Saturated vapour pressure for any one agent varies with temperature, and plenum vaporisers are designed to operate within a specific temperature range. They have several features designed to compensate for temperature changes (especially cooling by
evaporation). They often have a metal jacket weighing about 5kg, which equilibrates with the temperature in the room and provides a source of heat. In addition, the entrance to the vaporising chamber is controlled by a bimetallic strip, which admits more gas to the chamber as it cools, to compensate for the loss of efficiency of evaporation.
The first temperature-compensated plenum vaporiser was the
Cyprane'FluoTEC' Halothanevaporiser, released onto the market shortly after Halothanewas introduced into clinical practice in 1956.
The drawover vaporiser is driven by
negative pressuredeveloped by the patient, and must therefore have a low resistance to gas flow. Its performance depends on the minute volumeof the patient: its output drops with increasing minute ventilation.
The design of the drawover vaporiser is much more simple: in general it is a simple glass reservoir mounted in the breathing attachment. Drawover vaporisers may be used with any liquid volatile agent (including older agents such as
diethyl etheror chloroform, although it would be dangerous to use desflurane). Because the performance of the vaporiser is so variable, accurate calibration is impossible. However, many designs have a lever which adjusts the amount of fresh gas which enters the vaporising chamber.
The drawover vaporiser may be mounted either way round, and may be used in circuits where re-breathing takes place, or inside the circle breathing attachment.
Drawover vaporisers typically have no temperature compensating features. With prolonged use, the liquid agent may cool to the point where condensation and even frost may form on the outside of the reservoir. This cooling impairs the efficiency of the vaporiser. One way of minimising this effect is to place the vaporiser in a bowl of water.
The relative inefficiency of the drawover vaporiser contributes to its safety. A more efficient design would produce too much anaesthetic vapour. The output concentration from a drawover vaporiser may greatly exceed that produced by a plenum vaporiser, especially at low flows. For safest use, the concentration of anaesthetic vapour in the breathing attachment should be continuously monitored.
Despite its drawbacks, the drawover vaporiser is cheap to manufacture and easy to use. In addition, its portable design means that it can be used in the field or in
Dual-circuit gas-vapour blender
The third category of vaporiser (a dual-circuit gas-vapour blender) was created specifically for the agent
desflurane. Desflurane boils at 23.5C, which is very close to room temperature. This means that at normal operating temperatures, the saturated vapour pressure of desflurane changes greatly with only small fluctuations in temperature. This means that the features of a normal plenum vaporiser are not sufficient to ensure an accurate concentration of desflurane. Additionally, on a very warm day, all the desflurane would boil, and very high (potentially lethal) concentrations of desflurane might reach the patient.
A desflurane vaporiser (e.g. the TEC 6 produced by
Datex-Ohmeda) is heated to 39C and pressurised to 200kPa (and therefore requires electrical power). It is mounted on the anaesthetic machine in the same way as a plenum vaporiser, but its function is quite different. It evaporates a chamber containing desflurane using heat, and injects small amounts of pure desflurane vapour into the fresh gas flow. A transducersenses the fresh gas flow.
A warm-up period is required after switching on. The desflurane vaporiser will fail if mains power is lost. Alarms sound if the vaporiser is nearly empty. An electronic display indicates the level of desflurane in the vaporiser.
The expense and complexity of the desflurane vaporiser have contributed to the relative lack of popularity of desflurane, although in recent years it is gaining in popularity.
Wikimedia Foundation. 2010.
Look at other dictionaries:
Anaesthetic machine — The anaesthetic machine (or anesthesia machine in America) is used by anaesthesiologists to support the administration of anaesthesia. The most common type of anaesthetic machine in use in the developed world is the continuous flow anaesthetic… … Wikipedia
Volatile anaesthetic — The volatile anaesthetics are a class of general anaesthetic drugs. They share the property of being liquid at room temperature, but evaporating easily for administration by inhalation (some experts make a distinction between volatile and gas… … Wikipedia
Cyprane — A British anaesthetic equipment manufacturer founded in 1949 by Wilfred Jones and William Edmondson in Keighley, Yorkshire. The founders had previously worked for Coxeter, another manufacturer of anaesthetic equipment and subsequently BOC after… … Wikipedia
Nitrous oxide — N2O redirects here. For other uses, see N2O (disambiguation). Laughing gas redirects here. For other uses, see Laughing gas (disambiguation). Not to be confused with nitric oxide (formula NO) or nitrogen dioxide (formula NO2). For other uses, see … Wikipedia
Fresh gas flow — refers to the mixture of medical gases and volatile anaesthetic agents which is produced by an anaesthetic machine. The flow rate and composition of the fresh gas flow is determined by the anaesthetist.Typically the fresh gas flow emerges from… … Wikipedia
Desflurane — Systematic (IUPAC) name 2 (difluoromethoxy) 1,1,1,2 tetrafluor … Wikipedia
Epidural — This article is about the anaesthetic technique. For the anatomical site, see Epidural space. For other uses, see Epidural (disambiguation). Did you mean Epidural hematoma, a type of traumatic brain injury? Epidural Intervention … Wikipedia
Anesthesia — Not to be confused with Paresthesia. For other uses, see Anesthesia (disambiguation). Anesthesia, or anaesthesia (see spelling differences; from Greek αν , an , without ; and αἴσθησις, aisthēsis, sensation ), traditionally meant the condition of… … Wikipedia
Malignant hyperthermia — Classification and external resources Abnormalities in the Ryanodine receptor 1 gene are commonly detected in malignant hyperthermia ICD 10 T … Wikipedia
Minimum alveolar concentration — or MAC is a concept used to compare the strengths, or potency, of anaesthetic vapours; in simple terms, it is defined as the concentration of the vapour in the lungs that is needed to prevent movement (motor response) in 50% of subjects in… … Wikipedia