- Beam (structure)
A beam is a horizontal structural element that is capable of withstanding load primarily by resisting bending. The bending force induced into the material of the beam as a result of the external loads, own weight, span and external reactions to these loads is called a bending moment.
Beams generally carry vertical gravitational forces but can also be used to carry horizontal loads (i.e., loads due to an earthquake or wind). The loads carried by a beam are transferred to columns, walls, or girders, which then transfer the force to adjacent structural compression members. In light frame construction the joists rest on the beam.
Types of beams
Beams are characterized by their profile (the shape of their cross-section), their length, and their material. In contemporary construction, beams are typically made of steel, reinforced concrete, or wood. One of the most common types of steel beam is the I-beam or wide-flange beam (also known as a "universal beam" or, for stouter sections, a "universal column"). This is commonly used in steel-frame buildings and bridges. Other common beam profiles are the C-channel, the hollow structural section beam, the pipe, and the angle.
Beams are also described by how they are supported. Supports restrict lateral and/or rotational movements so as to satisfy stability conditions as well as to limit the deformations to a certain allowance. A simple beam is supported by a pin support at one end and a roller support at the other end. A beam with a laterally and rotationally fixed support at one end with no support at the other end is called a cantilever beam. A beam simply supported at two points and having one end or both ends extended beyond the supports is called an overhanging beam.
Moment of inertia
The moment of inertia of an object about a given axis describes how difficult it is to change its angular motion about that axis. Therefore, it encompasses not just how much mass the object has overall, but how far each bit of mass is from the axis. The farther out the object's mass is, the more rotational inertia the object has, and the more force is required to change its rotation rate.
Stress in beams
Internally, beams experience compressive, tensile and shear stresses as a result of the loads applied to them. Typically, under gravity loads, the original length of the beam is slightly reduced to enclose a smaller radius arc at the top of the beam, resulting in compression, while the same original beam length at the bottom of the beam is slightly stretched to enclose a larger radius arc, and so is under tension. The same original length of the middle of the beam, generally halfway between the top and bottom, is the same as the radial arc of bending, and so it is under neither compression nor tension, and defines the neutral axis (dotted line in the beam figure). Above the supports, the beam is exposed to shear stress. There are some reinforced concrete beams in which the concrete is entirely in compression with tensile forces taken by steel tendons. These beams are known as prestressed concrete beams, and are fabricated to produce a compression more than the expected tension under loading conditions. High strength steel tendons are stretched while the beam is cast over them. Then, when the concrete has cured, the tendons are slowly released and the beam is immediately under eccentric axial loads. This eccentric loading creates an internal moment, and, in turn, increases the moment carrying capacity of the beam. They are commonly used on highway bridges.
The primary tool for structural analysis of beams is the Euler–Bernoulli beam equation. Other mathematical methods for determining the deflection of beams include "method of virtual work" and the "slope deflection method". Engineers are interested in determining deflections because the beam may be in direct contact with a brittle material such as glass. Beam deflections are also minimized for aesthetic reasons. A visibly sagging beam, even if structurally safe, is unsightly and to be avoided. A stiffer beam (high modulus of elasticity and high second moment of area) produces less deflection.
Mathematical methods for determining the beam forces (internal forces of the beam and the forces that are imposed on the beam support) include the "moment distribution method", the force or flexibility method and the direct stiffness method.
Most beams in reinforced concrete buildings have rectangular cross sections, but the most efficient cross section for a simply supported beam is an I or H section. Because of the parallel axis theorem and the fact that most of the material is away from the neutral axis, the second moment of area of the beam increases, which in turn increases the stiffness.
An I-beam is only the most efficient shape in one direction of bending: up and down looking at the profile as an I. If the beam is bent side to side, it functions as an H where it is less efficient. The most efficient shape for both directions in 2D is a box (a square shell) however the most efficient shape for bending in any direction is a cylindrical shell or tube. But, for unidirectional bending, the I or wide flange beam is superior.
Efficiency means that for the same cross sectional area (volume of beam per length) subjected to the same loading conditions, the beam deflects less.
Other shapes, like L (angles), C (channels) or tubes, are also used in construction when there are special requirements.
- Beam engine
- Building code
- Classical mechanics
- Deflection (engineering)
- Elasticity (physics) and Plasticity (physics)
- Euler–Bernoulli beam equation
- Flexural modulus
- Finite element method in structural mechanics
- Free body diagram
- Influence line
- Materials science and Strength of materials
- Moment (physics)
- Poisson's ratio
- Post and lintel
- Shear strength
- Statics and Statically indeterminate
- Stress (physics) and Strain (materials science)
- Tensile strength, tensile stress and Hooke's law
- Thin-shell structure
- Yield (engineering)
- Popov, Egor P. (1968). Introduction to mechanics of solids. Prentice-Hall. ISBN 9780137261598.
- David Childs Ltd Consulting Civil Engineers: Tutorials
- American Wood Council: Free Download Library Wood Construction Data
- Introduction to Structural Design, U. Virginia Dept. Architecture
- U. Maryland, J.A. Clark School of Engineering: HAMLET engineering simulations and models
- U. Wisconsin–Stout, Strength of Materials online lectures, problems, tests/solutions, links, software
- Beam calculations in MS Excel from ExcelCalcs.com
- Beam Calculation Software for Windows from beams.com
- Types of load on structure
Wikimedia Foundation. 2010.
Look at other dictionaries:
Beam — may refer to: *Beam (structure), a construction element *Beam (nautical), the most extreme width (or breadth) of a nautical vessel, or a point alongside the ship at the mid point of its length *A narrow, propagating stream of particles or energy … Wikipedia
Beam lead Technology — is the name given to the structure and method of micro fabricating a semiconductor device structure. Its original application was to high frequency silicon switching transistors and ultra high speed integrated circuits. HistoryIn the early 1960 s … Wikipedia
Beam-powered propulsion — is a class of spacecraft propulsion mechanisms that use energy beamed to the spacecraft from a remote power plant. Most designs are rocket engines where the energy is provided by the beam, and is used to superheat propellant that then provides… … Wikipedia
Beam stack search — is a search algorithm which integrates backtracking with beam search.It was recently proposed by Rong Zhou and Eric A. Hansen, Department of Computer Science and Engineering, Mississippi State University during the 15th International Conference… … Wikipedia
Structure factor — In physics, in the area of crystallography, the structure factor of a crystal is a mathematical description of how the crystal scatters incident radiation. The structure factor is a particularly useful tool in the interpretation of interference… … Wikipedia
beam — beamless, adj. beamlike, adj. /beem/, n. 1. any of various relatively long pieces of metal, wood, stone, etc., manufactured or shaped esp. for use as rigid members or parts of structures or machines. 2. Building Trades. a horizontal bearing… … Universalium
Beam tetrode — The problem of secondary emission in the tetrode tube (valve) was solved by Philips/Mullard with the introduction of a suppressor grid to produce the pentode construction. Since Philips held a patent on this design, other manufacturers were keen… … Wikipedia
beam — n. & v. n. 1 a long sturdy piece of squared timber or metal spanning an opening or room, usu. to support the structure above. 2 a a ray or shaft of light. b a directional flow of particles or radiation. 3 a bright look or smile. 4 a a series of… … Useful english dictionary
beam — i. A processed and directed pulse of energy. ii. An invisible path produced by radio signals. An aircraft can follow the beam when approaching or going away from a navigational fix. A radar detects an aircraft when it is illuminated by its beam.… … Aviation dictionary
Electron beam induced deposition — (EBID) is a process of decomposing gaseous molecules by electron beam leading to deposition of non volatile fragments onto a nearby substrate. Process Focused electron beam of scanning electron microscope (SEM) or scanning transmission electron… … Wikipedia