Trucker's hitch

Trucker's hitch
trucker's hitch
TruckersHitchUsingAlpineButterfly2.jpg

Trucker's hitch with alpine butterfly loop
Names trucker's hitch, lorry driver's hitch,[1] harvester's hitch,[1] hay knot,[2] sheepshank cinch,[2] trucker's dolly,[3] wagoner's hitch,[3] power cinch[4]
Category Hitch
Related versatackle knot, sheepshank
Typical use Making a rope very tight, such as to secure an object to a vehicle
Caveat Can produce excessive wear on rope, especially if tied repeatedly in the same spot
ABoK #1514, #2124, #2125, #2126

The trucker's hitch is a compound knot commonly used for securing loads on trucks or trailers. This general arrangement, using loops and turns in the rope itself to form a crude block and tackle, has long been used to tension lines and is known by multiple names.[1][2] Knot author Geoffrey Budworth claims the knot can be traced back to the days when carters and hawkers used horse-drawn conveyances to move their wares from place to place.[5]

Contents

Variations

The portion of the trucker's hitch which differs in the following variations is the method used to form the loop which the working end slides through to produce the mechanical advantage. The different methods of forming the loop affect the ease and speed of tying and releasing and the stability of the final product.

The variations are presented in order of increasing stability.

Sheepshank style loop

This version of the knot uses a sheepshank-like construction, in this kind of application also known as a bell ringer's knot, to form the loop. It is quicker to make than a fixed loop, but is less dependable.[1][6] It is avoided in critical applications (such as securing a load on a truck) as it can fall apart under too little load or too much load, and can capsize if not dressed properly.[3] However, this knot may be made secure by adding a Half Hitch by using the top bight of the Sheepshank. This form of the trucker's hitch is least likely to jam, coming apart easily once tension is released. Different sources show slight variations in the way the sheepshank portion is formed and dressed.

Slipped overhand loop

The loop formed in this version is a simple Slipped Overhand Loop or a variation using multiple turns of rope to form the eye of the loop. If extra loops are used to form the eye it tends to ease untying. In order to prevent the closing of the loop under load, the loop must be formed by the working end of the rope (which will later pass through the loop). If the standing end goes through the loop, it will close under load.

Fixed loop

The most reliable common variation uses a fixed loop, such as an alpine butterfly loop, artillery loop, figure-eight loop, or another of many suitable loop knots.[3][7] If a fixed loop is used repeatedly for tying the trucker's hitch in the same portion of rope, excessive wear or other damage may be suffered by the portion of the loop which working end slides against.[1]

Finishing the hitch

In tightening the trucker's hitch, tension can be effectively increased by repeatedly pulling sideways while preventing the tail end from slipping through the loop, and then cinching the knot tighter as the sideways force is released. This is called "sweating a line".[8]

Once tight, the trucker's hitch is often secured with a half hitch, usually slipped for easy releasing and to avoid the necessity of access to the end of the rope, though a more secure finish, such as two half hitches, may be called for. Under large loads, the finishing half hitch can jam, especially if it is not slipped; the difficulty of releasing it can be compounded by the fact that the knot is typically still under tension when it is untied.

Mechanical advantage and friction

Conceptually similar arrangement of pulleys

All common variations of the trucker's hitch use a loop in the standing part of the rope and the anchor point as make-shift pulleys in order to theoretically obtain a 3 to 1 mechanical advantage while pulling on the working end.

There is sometimes confusion about how much theoretical mechanical advantage is provided by the trucker's hitch. If the trucker's hitch were to be used as in the pulley diagram at right, to lift a weight off the floor, the theoretical mechanical advantage would be only 2:1. However in the common use of the trucker's hitch, a static hook, ring, or rail, serves as the lower pulley, and the rope across the top of the load is the portion being tensioned. Thus, the standing part of the rope is represented by the top anchor point in the diagram, and the theoretical ratio is indeed 3:1 when the working end is tensioned. That is, in a frictionless system, every unit of force exerted on the working end would produce 3 units in the standing part of the rope over the load. In the typical use of the trucker's hitch, where it is used to tighten a rope over a load, when the end is secured to the loop of the Truckers hitch and let go, the tension in the two segments of rope around the ring will rise 50%, unless the rope slackens when it is being tied off, in which case the tension may drop to any value or even zero if enough slack is allowed. But when the trucker's hitch is used as in the diagram, after tying off, the load on the attachment point above the top pulley will drop to 400 lb and the tension in the two lines going to the lower pulley will not change.

Theoretical considerations aside, in real world use the mechanical advantage of the trucker's hitch is significantly less than the ideal case due to the effects of friction. Friction has been reported to reduce the mechanical advantage from 3 to 1, down to less than 1 to 1 in many cases. One advantage of the friction within the trucker's hitch, compared to a hypothetical pulley-based system, is that it allows the hitch to be held taut with less force while the working end is secured.

See also

References

  1. ^ a b c d e Des Pawson (2002), Pocket Guide to Knots & Splices, Edison, NJ: Chartwell Books, Inc., p. 142 
  2. ^ a b c Cyrus Lawrence Day (1986), The Art of Knotting and Splicing (4th ed.), Annapolis: Naval Institute Press, p. 116 
  3. ^ a b c d Gordon Perry (2006), Knots, North Vancouver: Quantum Publishing, pp. 134–135 
  4. ^ Cliff Jacobson (1977), Wilderness Canoeing & Camping, Dutton, p. 118, "...there seems to be no widely accepted name for this hitch, so I took the liberty of naming it the power-cinch" 
  5. ^ Geoffrey Budworth (1999), The Ultimate Encyclopedia of Knots, London: Hermes House, pp. 224–225 
  6. ^ Ashley, Clifford W. (1944), The Ashley Book of Knots, New York: Doubleday, p. 344, "A quicker but less dependable lashing is based on the Bell Ringer's Knot #1148." 
  7. ^ Ashley, p. 271
  8. ^ John Mellor (1996), Handling Troubles Afloat, Dobbs Ferry, NY: Sheridan House, pp. 195–196 

External links


Wikimedia Foundation. 2010.

Игры ⚽ Поможем написать курсовую

Look at other dictionaries:

  • hitch — hitch1 [hıtʃ] v 1.) [I and T] informal to get free rides from the drivers of passing cars by standing at the side of the road and putting a hand out with the thumb raised = ↑hitchhike hitch across/around/to ▪ He plans to hitch right round the… …   Dictionary of contemporary English

  • hitch — 1 verb 1 (I, T) informal to ask for a free ride from the drivers of passing cars by putting your hand out with your thumb raised; hitchhike (+ across/around/to): They hitched all the way across Europe. | hitch a ride with sb: We hitched a ride… …   Longman dictionary of contemporary English

  • Taut-line hitch — Names Taut line hitch, Adjustable hitch, Rigger s hitch, Midshipman s hitch, Tent line hitch, Tent hitch Category Hitch …   Wikipedia

  • List of hitch knots — A hitch is a type of knot used for binding rope to a part of a ship or other vehicle or object. This is an alphabetical list of hitch knots.*adjustable grip hitch *alternate ring hitching *anchor bend variant *bale sling hitch *barrel hitch… …   Wikipedia

  • Buntline hitch — Knot details name= Buntline hitch caption=Left: Buntline hitch Right: Slipped buntline hitch names= Studding sail tack bend, Inside clove hitch type= hitch strength= origin= related= Clove hitch, Two half hitches, Lobster buoy hitch releasing=… …   Wikipedia

  • Knot — For speeds, see Knot (unit). For other uses, see Knot (disambiguation). Some knots 1 Yarn knot ABoK #2688 2 Manrope knot 3 Granny knot 4 Rosebud stopper knot(?) …   Wikipedia

  • List of knots — This list of knots includes many alternate names for common knots. Knot names have evolved over time and there are many conflicting or confusing naming issues. The overhand knot, for example, is also known as the thumb knot. The figure of eight… …   Wikipedia

  • Lashing (ropework) — A lashing is an arrangement of rope used to secure two or more items together in a somewhat rigid manner. Lashings are most commonly applied to timber poles, and are commonly associated with the scouting movement and with sailors. This word usage …   Wikipedia

  • Block and tackle — A block and tackle [ Tackle can be pronEng|ˈteɪkəl in this usage.] is a system of two or more pulleys with a rope or cable threaded between them, usually used to lift or pull heavy loads. TOC Overview Although used in many situations, they are… …   Wikipedia

  • Dutchman — can refer to: A person of Dutch descent. A derogatory term for an Afrikaner from South Africa. (Theater) A Dutchman is a strip of material used to cover the join between two flats Norm Van Brocklin, a Hall of Fame quarterback who played for the… …   Wikipedia

Share the article and excerpts

Direct link
Do a right-click on the link above
and select “Copy Link”