- Solar panel
A solar panel (photovoltaic module or photovoltaic panel) is a packaged, connected assembly of solar cells, also known as photovoltaic cells. The solar panel can be used as a component of a larger photovoltaic system to generate and supply electricity in commercial and residential applications.
Because a single solar panel can produce only a limited amount of power, many installations contain several panels. A photovoltaic system typically includes an array of solar panels, an inverter, and sometimes a battery and interconnection wiring.
Theory and construction
Solar panels use light energy (photons) from the sun to generate electricity through the photovoltaic effect. The structural (load carrying) member of a module can either be the top layer or the back layer. The majority of modules use wafer-based crystalline silicon cells or thin-film cells based on cadmium telluride or silicon. The conducting wires that take the current off the panels may contain silver, copper or other non-magnetic conductive transition metals.
The cells must be connected electrically to one another and to the rest of the system. Cells must also be protected from mechanical damage and moisture. Most solar panels are rigid, but semi-flexible ones are available, based on thin-film cells.
Separate diodes may be needed to avoid reverse currents, in case of partial or total shading, and at night. The p-n junctions of mono-crystalline silicon cells may have adequate reverse current characteristics that these are not necessary. Reverse currents waste power and can also lead to overheating of shaded cells. Solar cells become less efficient at higher temperatures and installers try to provide good ventilation behind solar panels.
Some recent solar panel designs include concentrators in which light is focused by lenses or mirrors onto an array of smaller cells. This enables the use of cells with a high cost per unit area (such as gallium arsenide) in a cost-effective way.
Depending on construction, photovoltaic panels can produce electricity from a range of frequencies of light, but usually cannot cover the entire solar range (specifically, ultraviolet, infrared and low or diffused light). Hence much of the incident sunlight energy is wasted by solar panels, and they can give far higher efficiencies if illuminated with monochromatic light. Therefore, another design concept is to split the light into different wavelength ranges and direct the beams onto different cells tuned to those ranges. This has been projected to be capable of raising efficiency by 50%.
Currently the best achieved sunlight conversion rate (solar panel efficiency) is around 21% in commercial products, typically lower than the efficiencies of their cells in isolation. The energy density of a solar panel is the efficiency described in terms of peak power output per unit of surface area, commonly expressed in units of watts per square foot (W/ft2). The most efficient mass-produced solar panels have energy density values of greater than 13 W/ft2 (140 W/m2).
Crystalline silicon modules
Third generation solar cells are advanced thin-film cells. They produce high-efficiency conversion at low cost.
Rigid thin-film modules
In rigid thin film modules, the cell and the module are manufactured in the same production line.
The cell is created on a glass substrate or superstrate, and the electrical connections are created in situ, a so called "monolithic integration". The substrate or superstrate is laminated with an encapsulant to a front or back sheet, usually another sheet of glass.
Flexible thin-film modules
Flexible thin film cells and modules are created on the same production line by depositing the photoactive layer and other necessary layers on a flexible substrate.
If it is a conductor then another technique for electrical connection must be used.
The cells are assembled into modules by laminating them to a transparent colourless fluoropolymer on the front side (typically ETFE or FEP) and a polymer suitable for bonding to the final substrate on the other side. The only commercially available (in MW quantities) flexible module uses amorphous silicon triple junction (from Unisolar).
So-called inverted metamorphic (IMM) multijunction solar cells made on compound-semiconductor technology are just becoming commercialized in July 2008. The University of Michigan's solar car that won the North American Solar Challenge in July 2008 used IMM thin-film flexible solar cells.
The requirements for residential and commercial are different in that the residential needs are simple and can be packaged so that as solar cell technology progresses, the other base line equipment such as the battery, inverter and voltage sensing transfer switch still need to be compacted and unitized for residential use. Commercial use, depending on the size of the service will be limited in the photovoltaic cell arena, and more complex parabolic reflectors and solar concentrators are becoming the dominant technology.
The global flexible and thin-film photovoltaic (PV) market, despite caution in the overall PV industry, is expected to experience a CAGR of over 35% to 2019, surpassing 32 GW according to a major new study by IntertechPira.
Module embedded electronics
Several companies have begun embedding electronics into PV modules. This enables performing [[[maximum power point tracking]] (MPPT) for each module individually, and the measurement of performance data for monitoring and fault detection at module level. Some of these solutions make use of power optimizers, a DC-to-DC converter technology developed to maximize the power harvest from solar photovoltaic systems. As of about 2010, such electronics can also compensate for shading effects, wherein a shadow falling across a section of a panel causes the electrical output of one or more strings of cells in the panel to fall to zero, but not having the output of the entire panel fall to zero.
Module performance and lifetime
Electrical characteristics include nominal power (PMAX, measured in W), open circuit voltage (VOC), short circuit current (ISC, measured in amperes), maximum power voltage (VMPP), maximum power current (IMPP), peak power, kWp, and module efficiency (%).
Nominal voltage refers to the voltage of the battery that the module is best suited to charge; this is a leftover term from the days when solar panels were used only to charge batteries. The actual voltage output of the panel changes as lighting, temperature and load conditions change, so there is never one specific voltage at which the panel operates. Nominal voltage allows users, at a glance, to make sure the panel is compatible with a given system.
Open circuit voltage or VOC is the maximum voltage that the panel can produce when not connected to an electrical circuit or system. VOC can be measured with a meter directly on an illuminated panel's terminals or on its disconnected cable.
The peak power rating, kWp, is the maximum output according under standard test conditions (not the maximum possible output).
Solar panels must withstand heat, cold, rain and hail for many years. Many crystalline silicon module manufacturers offer a warranty that guarantees electrical production for 10 years at 90% of rated power output and 25 years at 80%.
15.9 GW of solar PV system installations were completed in 2010, with solar PV pricing survey and market research company PVinsights reporting growth of 117.8% in solar PV installation on a year-on-year basis. With over 100% year-on-year growth in PV system installation, PV module makers dramatically increased their shipments of solar panels in 2010. They actively expanded their capacity and turned themselves into gigawatt GW players. According to PVinsights, five of the top ten PV module companies in 2010 are GW players. Suntech, First Solar, Sharp, Yingli and Trina Solar are GW producers now, and most of them doubled their shipments in 2010.
Top ten producers
The top ten solar panel producers (by MW shipments) in 2010 were:
- First Solar
- Sharp Solar
- Trina Solar
- Canadian Solar
- Hanwha Solarone
- Renewable Energy Corporation
Average pricing information divides in three pricing categories: those buying small quantities (modules of all sizes in the kilowatt range annually), mid-range buyers (typically up to 10 MWp annually), and large quantity buyers (self explanatory—and with access to the lowest prices). Over the long term—and only in the long-term—there is clearly a systematic reduction in the price of cells and modules. For example in 1998 it was estimated that the quantity cost per watt was about $4.50, which was 33 times lower than the cost in 1970 of $150.
Following to RMI, Balance-of-System (BoS) elements, this is, non-module cost of non-microinverter solar panels (as wiring, converters, racking systems and various components) make up about half of the total costs of installations. Also, standardizing technologies could encourage greater adoption of solar panels and, in turn, economies of scale.
Solar trackers increase the amount of energy produced per panel at a cost of mechanical complexity and need for maintenance. They sense the direction of the Sun and tilt the panels as needed for maximum exposure to the light.
Fixed racks hold panels stationary as the sun moves across the sky. The fixed rack sets the angle at which the panel is held. Tilt angles equivalent to an installation's latitude are common.
Ground mounted solar power systems consist of solar panels held in place by racks or frames that are attached to ground based mounting supports.
Ground based mounting supports include:
- Pole mounts, which are driven directly into the ground or embedded in concrete.
- Foundation mounts, such as concrete slabs or poured footings
- Ballasted footing mounts, such as concrete or steel bases that use weight to secure the solar panel system in position and do not require ground penetration. This type of mounting system allows for decommissioning or relocation of solar panel systems with no ground excavation.
Roof mounted solar power systems consist of solar panels held in place by racks or frames attached to roof based mounting supports.
Roof based mounting supports include:
- Pole mounts, which are attached directly to the roof structure and may use additional rails for attaching the panel racking or frames.
- Ballasted footing mounts, such as concrete or steel bases that use weight to secure the panel system in position and do not require through penetration. This mounting method allows for decommissioning or relocation of solar panel systems with no adverse effect on the roof structure.
Standards generally used in photovoltaic panels:
- IEC 61215 (crystalline silicon performance), 61646 (thin film performance) and 61730 (all modules, safety)
- ISO 9488 Solar energy—Vocabulary.
- UL 1703
- UL 1741
- CE mark
- Electrical Safety Tester (EST) Series (EST-460, EST-22V, EST-22H, EST-110).
Devices with photovoltaic modules
Electric devices that includes solar panels:
- Solar cell phone : Sharp announced that its first solar-powered cell phone would be released in summer, 2009.
- Solar lamp
- Solar notebook: IUNIKA makes the first Solar Powered Netbook, the Gyy.
- Solar-pumped laser
- Solar vehicle
- Solar plane
Space stations and various spacecraft employ, or have employed photovoltaic panels to generate power.
- Building-integrated photovoltaic (BIPV).
- Cleaning event (Mars Exploration Rover phenomenon)
- Distributed inverter architecture
- Domestic energy consumption; supplies energy requirement numbers for private homes which is needed for anyone thinking of installing their own PV solar panels
- Insulated glazing
- Moore's Law
- Photovoltaics e.g. applications
- Photovoltaic system
- List of photovoltaics companies
- Sky footage
- Smart grid
- Solar roadway
- UV degradation
- Solar pond
- Solar Module Quality Assurance
- ^ "Diodes". Kpsec.freeuk.com. http://www.kpsec.freeuk.com/components/diode.htm. Retrieved 2010-10-18.
- ^ STO: Very High Efficient Solar Cells
- ^ "World's most efficient solar panel". The Independent. 26.6.2011. http://www.independent.co.uk/environment/worlds-most-efficient-solar-cells-ready-for-use-in-the-uk-2200508.html.
- ^ "Global flexible and thin-film PV market expected to reach US$58b in 2019,reports by IntertechPira study". Globalsolartechnology. 2009-09-11. http://globalsolartechnology.com/index.php?option=com_content&task=view&id=3981&Itemid=9.
- ^ "Introduction to Solar Electricity and Residential Solar Panels – AltE". altestore.com. http://www.altestore.com/howto/Getting-Started-Renewable-Energy-Sustainable-Living/Introduction-to-Solar-Electricity/a89/. Retrieved September 3, 2010.
- ^ "CTI Solar sales brochure". cti-solar.com. http://www.cti-solar.com/userfiles/file/brochlet%20CTI-SOLAR%20vers%20EN.pdf. Retrieved September 3, 2010.
- ^ a b "PVinsights announces worldwide 2010 top 10 ranking of PV module makers". www.pvinsights.com. http://pvinsights.com/Report/ReportPMM04A.php. Retrieved 2011-5-6.
- ^ Harnessing Light. National Research Council. 1998. p. 162. http://www.nap.edu/catalog.php?record_id=5954.
- ^ Paula Mints (24 September 2009). "Module Pricing: Rational, Or Just Plain Nuts?". Photovoltaics World Magazine. http://qa.electroiq.com/index/display/semiconductors-article-display/5704398898/articles/Photovoltaics-World/industry-news/2009/september-2009/module-pricing__rational.html.
- ^ "Transition from Coal- to Solar-powered cell phones this summer « SET Energy". Setenergy.org. 2009-04-21. http://setenergy.org/2009/04/21/transition-from-coal-to-solar-powered-cell-phones-this-summer/. Retrieved 2010-10-18.
- ^ "Meet Gyy, The First Solar Powered Netbook". PCWorld. 2009-05-15. http://www.pcworld.com/article/164943/meet_gyy_the_first_solar_powered_netbook.html. Retrieved 2010-10-18.
- The Next Solar Frontier: Distributed Inverter Architecture
- UT Study: Solar Industry Responsible for Lead Emissions in Developing Countries
- Photoelectric effect
- History of photovoltaics
- Timeline of solar cells
- Solar insolation
- Solar constant
- Solar cell efficiency
- Third generation photovoltaic cell
- Solar cell research
- Quantum efficiency of a solar cell
- Cadmium telluride
- Polycrystalline silicon photovoltaics
- Thermodynamic efficiency limit
- Sun-free photovoltaics
- Polarizing organic photovoltaics
Photovoltaic systemSolar cells
System componentsSystem concepts
- Solar cell
- Solar panel
- Thin film solar cell
- Polymer solar cell
- Nanocrystal solar cell
- Organic solar cell
- Quantum dot solar cell
- Hybrid solar cell
- Plasmonic solar cell
- Carbon nanotubes in photovoltaics
- Dye-sensitized solar cell
- Cadmium telluride photovoltaics
- Copper indium gallium selenide solar cells
- Multijunction photovoltaic cell
- Printed solar panel
- Solar-powered refrigerator
- Solar air conditioning
- Solar lamp
- Solar charger
- Solar backpack
- Solar tree
- Solar-powered pump
- Solar-powered watch
- Solar Tuki
- Photovoltaic keyboard
- Solar road stud
- Solar cell phone charger
- Solar notebook
- Solar powered calculator
- Solar powered fountain
- Solar powered radio
- Solar powered flashlight
- Solar fan
- Solar street light
- Solar traffic light
Air transportWater transportSolar vehicle racing
- Solar vehicle
- Solar car
- Solar roadway
- Solar golf cart
- The Quiet Achiever
- Solar car racing
- List of solar car teams
- Solar challenge
- Solar Cup
- Blue Sky Solar Racing
- Frisian Solar Challenge
- UC Solar Team
- Solar Splash
- South African Solar Challenge
- Tour de Sol
- World Solar Challenge
- Hunt-Winston School Solar Car Challenge
- North American Solar Challenge
- Victorian Model Solar Vehicle Challenge
By countryList of countries by photovoltaics production
- Solar Energy Generating Systems
- Stand-alone photovoltaic power system
- Grid-connected photovoltaic power system
- Rooftop photovoltaic power station
- Topaz Solar Farm
- Solar Ark
- Solar Umbrella house
- Erlasee Solar Park
- Guadarranque solar power plant
- Pocking Solar Park
- Copper Mountain Solar Facility
- Wyandot Solar Facility
- Köthen Solar Park
- Building-integrated photovoltaics
- Moura Photovoltaic Power Station
- Nevada Solar One
- Beneixama photovoltaic power plant
- Gottelborn Solar Park
- Darro Solar Park
- Olmedilla Photovoltaic Park
- Blythe Photovoltaic Power Plant
- Strasskirchen Solar Park
- Puertollano Photovoltaic Park
- Alamosa photovoltaic power plant
PV companies Category · Commons
Wikimedia Foundation. 2010.
Look at other dictionaries:
solar panel — n. a large, thin panel consisting of an array of solar cells, often attached to artificial satellites, rooftops, etc. to generate electricity directly from sunlight … English World dictionary
solar panel — ► NOUN ▪ a panel designed to absorb the sun s rays as a source of energy for generating electricity or heating … English terms dictionary
solar panel — n a piece of equipment, usually kept on a roof, that collects and uses the sun s energy to heat water or make electricity … Dictionary of contemporary English
solar panel — noun count a piece of equipment that uses energy from the Sun to create power for a building … Usage of the words and phrases in modern English
solar panel — noun electrical device consisting of a large array of connected solar cells • Syn: ↑solar array, ↑solar battery • Hypernyms: ↑electrical device • Part Holonyms: ↑satellite, ↑artificial satellite, ↑ … Useful english dictionary
solar panel — UK / US noun [countable] Word forms solar panel : singular solar panel plural solar panels a piece of equipment that uses energy from the Sun to create power for a building … English dictionary
solar panel — /soʊlə ˈpænəl/ (say sohluh panuhl) noun 1. a glass sheet housing an interconnected assembly of solar cells which convert energy from the sun into electricity. 2. Also, solar heating panel. a panel which is part of a solar heating system … Australian English dictionary
solar panel — noun Date: 1961 a battery of solar cells (as in a spacecraft) … New Collegiate Dictionary
solar panel — a bank of solar cells. * * * … Universalium
solar panel — noun An array of connected solar cells … Wiktionary