Digital signal

﻿
Digital signal

A digital signal is a physical signal that is a representation of a sequence of discrete values (a quantified discrete-time signal), for example of an arbitrary bit stream, or of a digitized (sampled and analog-to-digital converted) analog signal. The term digital signal can refer to

1. a continuous-time waveform signal used in any form of digital communication.
2. a pulse train signal that switches between a discrete number of voltage levels or levels of light intensity, also known as a a line coded signal, for example a signal found in digital electronics or in serial communications using digital baseband transmissionin, or a pulse code modulation (PCM) representation of a digitized analog signal.

A signal that is generated by means of a digital modulation method (digital passband transmission), produced by a modem, is in the first case considered as a digital signal, and in the second case as converted to an analog signal.

Waveforms in digital systems

A digital signal waveform: (1) low level, (2) high level, (3) rising edge, and (4) falling edge.

In computer architecture and other digital systems, a waveform that switches between two voltage levels representing the two states of a Boolean value (0 and 1) is referred to as a digital signal, even though it is an analog voltage waveform, since it is interpreted in terms of only two levels.

The clock signal is a special digital signal that is used to synchronize digital circuits. The image shown can be considered the waveform of a clock signal. Logic changes are triggered either by the rising edge or the falling edge.

The given diagram is an example of the practical pulse and therefore we have introduced two new terms that are:

• Rising edge: the transition from a low voltage (level 1 in the diagram) to a high voltage (level 2).
• Falling edge: the transition from a high voltage to a low one.

Although in a highly simplified and idealised model of a digital circuit we may wish for these transitions to occur instantaneously, no real world circuit is purely resistive and therefore no circuit can instantly change voltage levels. This means that during a short, finite transition time the output may not properly reflect the input, and indeed may not correspond to either a logically high or low voltage.

Logic voltage levels

Hobbyist frequency counter circuit built almost entirely of TTL logic chips.

The two states of a wire are usually represented by some measurement of an electrical property: Voltage is the most common, but current is used in some logic families. A threshold is designed for each logic family. When below that threshold, the wire is "low," when above "high." Digital circuits establish a "no man's area" or "exclusion zone" that is wider than the tolerances of the components. The circuits avoid that area, in order to avoid indeterminate results.

It is usual to allow some tolerance in the voltage levels used; for example, 0 to 2 volts might represent logic 0, and 3 to 5 volts logic 1. A voltage of 2 to 3 volts would be invalid, and occur only in a fault condition or during a logic level transition. However, few logic circuits can detect such a condition and most devices will interpret the signal simply as high or low in an undefined or device-specific manner. Some logic devices incorporate schmitt trigger inputs whose behaviour is much better defined in the threshold region, and have increased resilience to small variations in the input voltage.

The levels represent the binary integers or logic levels of 0 and 1. In active-high logic, "low" represents binary 0 and "high" represents binary 1. Active-low logic uses the reverse representation.

Examples of binary logic levels:
Technology L voltage H voltage Notes
CMOS 0 V to VCC/2 VCC/2 to VCC VCC = supply voltage
TTL 0 V to 0.8 V 2 V to VCC VCC is 4.75 V to 5.25 V
ECL -1.175 V to -VEE 0.75 V to 0 V VEE is about -5.2 V. VCC=Ground

Wikimedia Foundation. 2010.

Look at other dictionaries:

• Digital Signal 1 — (DS1, sometimes DS 1) is a T carrier signaling scheme devised by Bell Labs.[1] DS1 is a widely used standard in telecommunications in North America and Japan to transmit voice and data between devices. E1 is used in place of T1 outside North… …   Wikipedia

• Digital Signal 0 — (DS0) is a basic digital signaling rate of 64 kbit/s, corresponding to the capacity of one voice frequency equivalent channel.[1] The DS0 rate, and its equivalents E0 and J0, form the basis for the digital multiplex transmission hierarchy in… …   Wikipedia

• digital signal —  Digital Signal  Цифровой сигнал   Сигнал, относящийся к системам, которые для передачи информации используют только квантованные (дискретные) состояния.  См. аналоговый сигнал …   Толковый англо-русский словарь по нанотехнологии. - М.

• Digital Signal 3 — DS3 redirects here. For the U.S. Army s Disabled Soldier Support System (DS3), see Army Wounded Warrior Program. For the car, see Citroën DS3. For the locomotive, see DS3 (locomotive). For the game, see Dungeon Siege III. A Digital Signal 3 (DS3) …   Wikipedia

• digital signal — skaitmeninis signalas statusas T sritis automatika atitikmenys: angl. digital signal vok. Digitalsignal, n rus. цифровой сигнал, m pranc. signal numérique, m …   Automatikos terminų žodynas

• digital signal — skaitmeninis signalas statusas T sritis informatika apibrėžtis Signalas, kurio vertė yra ↑skaitmeninis dydis. atitikmenys: angl. digital signal ryšiai: dar žiūrėk – skaitmeninis dydis palygink – analoginis signalas …   Enciklopedinis kompiuterijos žodynas

• Digital Signal — WikiV a) An electronic signal where every different value from the real life excitation (sound, light) has a different value of binary combinations (words) that represent the analog signal.[1] b) An analog signal that has been converted to a… …   Audio and video glossary

• digital signal — noun A signal that only takes discrete values (contrasted to an analog signal that can take continuously varying values) …   Wiktionary

• digital signal —    Abbreviated DS; also known as digital service. There are several levels of common carrier digital transmission service:    • DS 0 64Kbps.    • DS 1 1.544Mbps (T1).    • DS 1C    Two DS 1 channels are multiplexed into a single DS 1C 3.152Mbps… …   Dictionary of networking

• digital signal —    A discrete or discontinuous signal; one whose various states are discrete intervals apart. See also analog transmission …   IT glossary of terms, acronyms and abbreviations

We are using cookies for the best presentation of our site. Continuing to use this site, you agree with this.