- Soil liquefaction
Soil liquefaction describes the behavior of loose saturated unconsolidated soils, i.e. loose sands, which go from a solid state to have the consistency of a heavy liquid, or reach a liquefied state as a consequence of increasing porewater pressures, and thus decreasing
effective stress, induced by their tendency to decrease in volume when subjected to cyclic undrained loading (e.g. earthquake loading). Liquefaction is more likely to occur in loose to moderate granular soils with poor drainage, such as silty sands or sands and gravels capped or containing seams of impermeable sediments [Youd, T.L., and Idriss, I.M. (2001). "Liquefaction Resistance of Soils: Summary report from the 1996 NCEER and 1998 NCEER/NSF Workshops on Evaluation of Liquefaction Resistance of Soils", "Journal of Geotechnical and Geoenvironmental Engineering", ASCE, 127(4), 297-313] . Deposits most susceptible to liquefaction are young (Holocene-age, deposited within the last 10,000 years) sands and silts of similar grain size (well-sorted), in beds at least several feet thick, and saturated with water. Such deposits are often found along riverbeds, beaches, dunes, and areas where windblown silt (loess) and sand have accumulated. Some examples of liquefaction include quicksand, quick clay, turbidity currents, and earthquake liquefaction.
Depending on the initial
void ratio, the soil material can respond to loading either "strain-softening" or "strain-hardening". Strain-softened soils, e.g. loose sands, can be triggered to collapse, either monotonically or cyclically, if the static shear stress is greater than the ultimate or steady-state shear strengthof the soil. In this case "flow liquefaction" occurs, where the soil deforms at a low constant residual shear stress. If the soil strain-hardens, e.g. moderately dense to dense sand, flow liquefaction will generally not occur. However, "cyclic softening" can occur due to cyclic undrained loading, e.g. earthquake loading. Deformation during cyclic loading will depend on the density of the soil, the magnitude and duration of the cyclic loading, and amount of shear stress reversal. If stress reversal occurs, the effective shear stress could reach zero, then "cyclic liquefaction" can take place. If stress reversal does not occur, zero effective stress is not possible to occur, then "cyclic mobility" takes place [Robertson, P.K., and Fear, C.E. (1995). "Liquefaction of sands and its evaluation.", "Proceedings of the 1st International Conference on Earthquake Geotechnical Engineering", Tokyo] .
The resistance of the cohesionless soil to liquefaction will depend on the density of the soil, confining stresses, soil structure (fabric, age and cementation), the magnitude and duration of the cyclic loading, and the extent to which shear stress reversal occurs [Robertson, P.K., and Wride, C.E. (1998). "Evaluating Cyclic Liquefaction Potential using the cone penetration test." "Canadian Geotechnical Journal", Ottawa, 35(5), 442-459.] .
Although the effects of liquefaction have been long understood, it was more thoroughly brought to the attention of
engineers and seismologists in the 1964 Niigata, Japan and Alaskaearthquakes. It was also a major factor in the destruction in San Francisco's Marina Districtduring the 1989 Loma Prieta earthquake.
Earthquake liquefaction is a major contributor to
urban seismic risk. The shaking causes increased pore water pressurewhich reduces the effective stress, and therefore reduces the shear strength of the sand. If there is a dry soil crust or impermeable cap, the excess water will sometimes come to the surface through cracks in the confining layer, bringing liquefied sand with it, creating sand boils, colloquially called "sand volcanoes".
Studies of liquefaction features left by prehistoric earthquakes, called
paleoliquefactionor paleoseismology, can reveal a great deal of information about earthquakes that occurred before records were kept or accurate measurements could be taken. [http://earthquake.usgs.gov/research/hazmaps/whats_new/workshops/CEUS-WORKSHP/Tuesday/NE-Tuttle.2.pdf]
Quicksandforms when water saturates an area of loose sand and the ordinary sand is agitated. When the water trapped in the batch of sand cannot escape, it creates liquefied soil that can no longer support weight. Quicksand can be formed by standing or (upwards) flowing underground water (as from an underground spring), or by earthquakes. In the case of flowing underground water, the force of the water flow opposes the force of gravity, causing the granules of sand to be more buoyant. In the case of earthquakes, the shaking force can increase the pressure of shallow groundwater, liquefying sand and silt deposits. In both cases, the liquefied surface loses strength, causing buildings or other objects on that surface to sink or fall over.
The saturated sediment may appear quite solid until a change in pressure or shock initiates the liquifaction causing the sand to form a suspension with each grain surrounded by a thin film of water. This cushioning gives quicksand, and other liquefied sediments, a spongy, fluidlike texture. Objects in the liquefied sand sink to the level at which the weight of the object is equal to the weight of the displaced sand/water mix and the object "floats" due to its
Quick clay, also known as "Leda Clay" in Canada, is a unique form of highly sensitive clay, with the tendency to change from a relatively stiff condition to a liquid mass when it is disturbed. Undisturbed quick clay resembles a water-saturated gel. When a block of clay is held in the hand and struck, however, it instantly turns into a flowing ooze, a process known as spontaneous liquefaction. Quick clay behaves this way because, although it is solid, it has a very high water content, up to 80%. The clay retains a solid structure despite the high water content, because surface tensionholds water-coated flakes of clay together in a delicate structure. When the structure is broken by a shock, it reverts to a fluid state.
Quick clay is only found in the northern countries such as
Russia, Canada, Alaskain the U.S., Norway, Sweden, and Finland, which were glaciated during the Pleistocene epoch.
Quick clay has been the underlying cause of many deadly
landslides. In Canada alone, it has been associated with more than 250 mapped landslides. Some of these are ancient, and may have been triggered by earthquakes. [http://geoscape.nrcan.gc.ca/ottawa/landslides_e.php]
Submarine landslides are
turbidity currents and consist of water saturated sediments flowing downslope. An example occurred during the 1929 Grand Banks earthquakethat struck the continental slopeoff the coast of Newfoundland. Minutes later, transatlantic telephone cables began breaking sequentially, farther and farther downslope, away from the epicenter. Twelve cables were snapped in a total of 28 places. Exact times and locations were recorded for each break. Investigators suggested that a 60-mile-per-hour (100 km/h) submarine "landslide" or turbidity current of water saturated sediments swept 400 miles (600 km) down the continental slopefrom the earthquake’s epicenter, snapping the cables as it passed. [Bruce C. Heezen and Maurice Ewing, “Turbidity Currents and Submarine Slumps, and the 1929 Grand Banks Earthquake,” American Journal of Science, Vol. 250, December 1952, pp. 849–873.]
Liquefaction can cause damage to structures in several ways. [ [http://www.es.ucsc.edu/~es10/fieldtripEarthQ/Damage1.html Damage Caused by EarthQuakes ] ] Buildings whose foundations bear directly on sand which liquefies will experience a sudden loss of support, which will result in drastic and irregular settlement of the building. Liquefaction causes irregular settlements in the area liquefied, which can damage buildings and break underground utility lines where the differential settlements are large. Pipelines and ducts may float up through the liquefied sand. Sand boils can erupt into buildings through utility openings, and may allow water to damage the structure or electrical systems. Soil liquefaction can also cause slope failures. Areas of
land reclamationare often prone to liquefaction because many are reclaimed with hydraulic fill, and are often underlain by soft soils which can amplify earthquake shaking. Soil liquefaction was a major factor in the destruction in San Francisco's Marina Districtduring the 1989 Loma Prieta earthquake. Mitigating potential damage from liquefaction is part of the field of geotechnical engineering.
Sand volcanoor sand blow
* [http://www.ce.washington.edu/~liquefaction/html/main.html Soil Liquefaction]
* [http://www.pnsn.org/SEIS/EQ_Special/WEBDIR_01022818543p/quakestory.html Shaking, Liquefaction on Harbor Island] , one of the few known live observations of an earthquake liquefaction event by a seismologist
Wikimedia Foundation. 2010.
Look at other dictionaries:
soil liquefaction — /ˈsɔɪl lɪkwəfækʃən/ (say soyl likwuhfakshuhn) noun the process by which a saturated substratum of soil, especially a sandy soil, loses its cohesion, in the process losing its ability to transfer load, as the weight of buildings, from the ground… … Australian English dictionary
Soil mechanics — is a discipline that applies principles of engineering mechanics, e.g. kinematics, dynamics, fluid mechanics, and mechanics of material, to predict the mechanical behavior of soils. Together with Rock mechanics, it is the basis for solving many… … Wikipedia
Liquefaction — may refer to:* Soil liquefaction, the process by which sediments become suspended * Liquefaction of gases in physics, chemistry, and thermal engineering * Liquefactive necrosis in pathology * Liquification, the general process of becoming liquid … Wikipedia
Liquéfaction du sol — Ne doit pas être confondu avec Solifluxion ni Sable mouvant. Immeuble endommagé suite à la liquéfaction du sol lors du séisme du 22 février 2011 en Nouvelle Zélande … Wikipédia en Français
Soil — For other uses, see Soil (disambiguation). A represents soil; B represents laterite, a regolith; C represents saprolite, a less weathered regolith; the bottommost layer represents bedrock … Wikipedia
liquefaction — /lɪkwəˈfækʃən/ (say likwuh fakshuhn) noun 1. the process of liquefying or making liquid. 2. a process which results in something with characteristics of a liquid, as in soil liquefaction … Australian English dictionary
liquefaction — noun Etymology: Middle English, from Late Latin liquefaction , liquefactio, from Latin liquefacere, from liquēre to be fluid + facere to make more at do Date: 15th century 1. the process of making or becoming liquid 2. the state of being liquid 3 … New Collegiate Dictionary
List of soil topics — *Atriplex (saltbush) *saline seep *salinity in Australia *salting the earth *(saltbush) Atriplex *soil amendment *(soil and water conservation district) conservation district *Soil Association *soil classification *soil conditioner *soil… … Wikipedia
Consolidation (soil) — Consolidation is a process by which soils decrease in volume. According to Karl Terzaghi consolidation is any process which involves decrease in water content of a saturated soil without replacement of water by air.  In general… … Wikipedia
Shear strength (soil) — Shear strength in reference to soil is a term used to describe the maximum strength of soil at which point significant plastic deformation or yielding occurs due to an applied shear stress. There is no definitive shear strength of a soil as it… … Wikipedia