- Cutter (ship)
When used in a nautical sense, a cutter is:
# a small single-masted vessel,
fore-and-aft rigged, with two or more headsails, a bowsprit, and a mastset further back than in a sloop
# a ship's boat, powered by oars, sails or motor, used to carry passengers or light stores
# a small or medium sized armed vessel used by various marine or naval services such as the U.S. Coast Guard.
Traditionally the sloop rig was a rig with a single mast located forward of 70% of the length of the sailplan. In this traditional definition a sloop could have multiple jibs on a fixed bowsprit. Cutters had a rig with a single mast more centrally located, which could vary from 50% to 70% of the length of the sailplan, with multiple headsails and a reeving bowsprit. A mast located aft of 50% would be considered a
mast aft rig.
Somewhere in the 1950s or 1960s there was a shift in these definitions such that a sloop only flew one headsail and a cutter had multiple headsails and mast position became irrelevant. In this modern idiom, then, a cutter is a
sailingvessel with more than one head sailand one mast. In a traditional vessel there would normally be also, a bowspritto carry a jibset flying from the bowsprit end via a traveller (to preserve the ability to reef the bowsprit), while in modern vessels the jib is set from a topmast forestay permanently fixed to the end of a fixed (non-reeving) bowsprit, or directly to the stem fitting of the bow itself. (The sloopcarries only one head sail, properly called a foresailthough nowadays usually called a jib.) Correctly speaking, a jib is set on the topmast forestay.
The term is English in origin and refers to a specific type of vessel, namely, "a small, decked ship with one mast and bowsprit, traditionally with a gaff mainsail, though not invariably so. The foot of the mainsail would normally be laced to a boom and the head to a gaff above which a gaff topsail would be set in suitable conditions. There would also be a foresail and jib and possibly a flying jib set above the jib."Fact|date=October 2007
The open cutter carried aboard naval vessels in the 18th Century was rowed by pairs of men sitting side-by-side on benches. The cutter, with its transom, was broader in proportion compared to the
longboat, which had finer lines.
Watermenof Londonused similar boats in the 18th Century often decorated as depicted in historical prints and pictures of the River Thamesin the 17th & 18th Centuries. The modern Waterman’s Cutter is based on drawings of these boats. They are convert|34|ft|m long with a beam of convert|4|ft|6|in|m|abbr=on They can have up to six oarsmen either rowing or sculling and can carry a cox and passengers. The organisers of the Great River Racedeveloped the modern version in the 1980’s and now many of the fleet of 24 compete annually in this "Marathon of the River". Watermen’s Cutters also compete annually in the Port of LondonChallenge, and the Port Admirals’ Challenge. Cutter races are also to be found at various town rowing and skiffing regattas. In addition the cutters perform the role of ceremonial Livery Barges with the canopies and armorial flags flying on special occasions. [ [http://www.traditionalrowing.com/ Thames Traditional Rowing Association] ]
Cutters been used for record-breaking attempts and crews have achieved record times for
scullingthe English Channel(2hrs 42mins) in 1996 and for sculling non-stop from London to Paris (4days 15minutes) in 1999. [ Guiness World Records]
A pulling cutter was a boat carried by sailing ships for work in fairly sheltered water in which load-carrying capacity was needed, for example in laying a kedge. This operation was the placing a relatively light anchor at a distance from the ship so as to be able to haul her off in its direction. The oars were double-banked. That is, there were two oarsmen on each thwart. In a seaway, the longboat was preferred to the cutter as the finer lines of the stern of the former meant that it was less likely to broach to in a following sea. In the
Royal Navythe cutters were replaced by 25 and convert|32|ft|m|sing=on motor cutters. However, the cutters' traditional work had grown beyond the capacity of a boat as ships became larger. Though primarily a pulling boat, this cutter could also be rigged for sailing.
Concerning the use of a kedge, see also:
USS Saratoga (1814)
HMS Sirius (1797)
Historically, a cutter is any seaworthy vessel used in the law enforcement duties of Great Britain's
HM Customs and Excise, the United States Department of the Treasury's Revenue Cutter Serviceor the customs services of other countries.
In America, customs cutters were commonly schooners or brigs. In Britain, they were usually rigged as defined under "Sailing" (above). The British Board of Customs also used other vessels as hulks, which were moored in places such as tidal creeks. Customs officers worked from the hulks in smaller boats.
In the UK, Customs currently operate a fleet of 42 m Corvette-type vessels throughout UK territorial waters as customs cutters, inspecting vessels for illicit cargoes.
United States Coast Guard
, which is now part of the Department of Homeland Security.
Today the Coast Guard officially uses the term "cutter" for any vessel which has a permanently assigned crew and accommodations for the extended support of that crew, although informally this is held to mean any vessel of convert|65|ft|m or more in length. [http://www.uscg.mil/directives/cim/5000-5999/CIM_5000_3B.pdf USCG Regulations] . Chapter 10. Accessed
November 25, 2007.]
Larger cutters, over 180 feet (55 m) in length, are under control of area commands (Atlantic area or Pacific area). Cutters at or under convert|180|ft|m in length come under control of district commands. Cutters usually have a motor surf boat and/or a rigid hull inflatable boat on board. Polar Class icebreakers also carry an Arctic survey boat (ASB) and landing craft.
* [http://www.uscg.mil/hq/g-cp/history/collect.html U. S. Coast Guard Historian's Office]
Wikimedia Foundation. 2010.
Look at other dictionaries:
Cutter v Powell — Court Court of King s Bench Date decided 9 June 1795 Citation(s) (1795) 6 TR 320; 101 ER 573 … Wikipedia
cutter — [kut′ər] n. 1. a device, tool, or machine for cutting 2. a person who cuts or whose work is cutting; specif., a person whose work is cutting to patterns the sections that form a garment 3. a) a boat carried, esp. formerly, aboard large ships to… … English World dictionary
cutter — late 12c., one who cuts in any sense, agent noun from CUT (Cf. cut) (v.). As a type of small, single masted vessel, from 1762, earlier boat belonging to a ship of war (1745), perhaps so called from the notion of cutting through the water … Etymology dictionary
cutter — ► NOUN 1) a person or thing that cuts. 2) a light, fast patrol boat or sailing boat. 3) a ship s boat used for carrying light stores or passengers. 4) Cricket & Baseball a ball that deviates sharply on pitching … English terms dictionary
Ship prefix — A ship prefix is a combination of letters, usually abbreviations, used in front of the name of a civilian or naval ship. Prefixes for civilian vessels may either identify the type of propulsion, such as SS for steamship, or purpose, such as RV… … Wikipedia
Cutter (boat) — A gaff cutter KLEINE FREIHEIT with a genoa jib set A cutter may refer to several types of nautical vessels. When used in the context of sailing vessels, a cutter is a small single masted boat, fore and aft rigged, with two or more headsails and… … Wikipedia
ship — I (New American Roget s College Thesaurus) Vehicle for navigation on water Nouns 1. ship, vessel, sail; craft, bottom; airship (see aviation). See navigation. 2. (naval organization) navy, marine, fleet, flotilla, argosy; shipping, merchant… … English dictionary for students
ship — Synonyms and related words: Graf Zeppelin, address, aeroplane, aerostat, air express, aircraft, airfreight, airmail, airplane, airship, argosy, ark, avion, back, bag, balance rudder, ballonet, balloon, barge, barrel, bathyscaphe, batten, beak,… … Moby Thesaurus
Cutter (G.I. Joe) — G.I. Joe character Cutter as seen in the Sunbow G.I. Joe cartoon. Cutter Affiliation G.I. Joe File name Stone, Skip A. Birthplace Kinsley, Ka … Wikipedia
cutter — /kut euhr/, n. 1. a person who cuts, esp. as a job, as one who cuts fabric for garments. 2. a machine, tool, or other device for cutting. 3. Naut. a. a single masted sailing vessel, very similar to a sloop but having its mast set somewhat farther … Universalium