Active load

An active or dynamic load is a component or a circuit behaving as a current-stable nonlinear resistor. This term may refer to a component of circuit design, or to a type of test equipment.

Circuit design

In circuit design, an active load is a circuit component made up of active devices, such as transistors, intended to present a high small-signal impedance yet not requiring a large DC voltage drop, as would occur if a large resistor were used instead. Such large AC load impedances may be desirable, for example, to increase the AC gain of some types of amplifier. Most commonly the active load is the output part of a current mirror^[1] and is represented in an idealized manner as a current source. Usually, it is only a constant-current resistor that is a part of the whole current source including a constant voltage source as well (the power supply V_CC on the figures below).

Common base example

Figure 1: Basic NPN common base circuit with resistor load (neglecting biasing details). Signal is applied at V_In, output taken from node V_out may be a voltage or a current

Figure 2: Basic NPN common base circuit (neglecting biasing details). Current source I_C represents an active load.

In Figure 1 the load is a resistor, and the current through the resistor is determined by Ohm's law as:

$I_C = \frac {V_{CC} - V_{out}} {R_C}$.

As a consequence of this relation, the voltage drop across the resistor is tied to the current at the Q-point. If the bias current is fixed for some performance reason, any increase in load resistance automatically leads to a lower voltage for V_out. which in turn lowers the voltage drop V_CB between collector and base, limiting the signal swing at the amplifier output (if the output swing is larger than V_CB, the transistor is driven out of active mode during part of the signal cycle).

In contrast, using the active load of Figure 2, the AC impedance of the ideal current source is infinite regardless of the voltage drop V_CC - V_out, which allows even a large value of V_CB. and consequently a large output signal swing.

Differential amplifiers

Active loads are frequently used in op-amp differential input stages, in order to enormously increase the gain.

Practical limitations

In practice the ideal current source is replaced by a current mirror, which is less ideal in two ways. First, its AC resistance is large, but not infinite. Second, the mirror requires a small voltage drop to maintain operation (to keep the output transistors of the mirror in active mode). As a result, the current mirror does limit the allowable output voltage swing, but this limitation is much less than for a resistor, and also does not depend upon the choice of bias current, leaving more flexibility than a resistor in designing the circuit.

Test equipment

In the area of electronic test equipment, an active load is used for automatic testing of power supplies and other sources of electrical power to ensure that their output voltage and current are within their specifications over a range of load conditions, from no load to maximum load.

One approach to test loads uses a set of resistors of different values, and manual intervention. In contrast, an active load presents to the source a resistance value varied by electronic control, either by an analogue adjusting device such as a multi-turn potentiometer or, in automated test setups, by a digital computer. The load resistance can often be varied rapidly in order to test the power supply's transient response.

Just like a resistor, an active load converts the power supply's electrical energy to heat. The heat-dissipating devices (usually transistors) in an active load therefore have to be designed to withstand the resulting temperature rise, and are usually cooled by means of heatsinks.

For added convenience, active loads often include circuitry to measure the current and voltage delivered to the inputs, and may display these measurements on numeric readouts.

External links

• "Precision active load operates as low as 2V", EDN Magazine, 2005

References

1. ^ Richard C. Jaeger, Travis N. Blalock (2004). Microelectronic Circuit Design (Second Edition ed.). New York: McGraw-Hill Professional. p. 1228. ISBN 0-07-250503-6. http://books.google.com/books?id=u6vH4Gsrlf0C&pg=RA1-PA1228&dq=%22active+load%22&as_brr=0&sig=9FuiBTRt73yyuZ7MDR9jSDJye_s.