- Engineering tolerance
Engineering tolerance is the permissible limit or limits of variation in
- a physical dimension,
- a measured value or physical property of a material, manufactured object, system, or service,
- other measured values (such as temperature, humidity, etc.).
- in engineering and safety, a physical distance or space (tolerance), as in a truck (lorry), train or boat under a bridge as well as a train in a tunnel (see structure gauge and loading gauge).
- in mechanical engineering the space between a bolt and a nut or a hole, etc..
Dimensions, properties, or conditions may vary within certain practical limits without significantly affecting functioning of equipment or a process. Tolerances are specified to allow reasonable leeway for imperfections and inherent variability without compromising performance.
A variation beyond the tolerance (for example, a temperature that's too hot or too cold) is said to be non-compliant, rejected, or exceeding the tolerance (regardless of if this breach was of the lower or the upper bound). If the tolerance is set too restrictive, resulting in most objects run by it being rejected, it is said to be intolerant.
Tolerances are often set by design engineers and published in specifications or contracts. Many technical standards have tolerances agreed upon by consensus discussions and sometimes formal voting procedures.
The tolerance may be specified as a factor or percentage of the nominal value, a maximum deviation from a nominal value, an explicit range of allowed values, be specified by a note or published standard with this information, or be implied by the numeric accuracy of the nominal value. Tolerance can be symmetrical, as in 40±0.1, or asymmetrical, such as 40+0.2/−0.1.
It is often desirable to specify the largest possible tolerance while maintaining proper functionality. Closer or tighter tolerances are more difficult, and hence costly, to achieve. Conversely, larger or looser tolerances may significantly affect the operation of the device.
Tolerance is different from safety factor, but an adequate safety factor will take into account relevant tolerances as well as other possible variations.
Considerations when setting tolerances
A primary concern is to determine how wide the tolerances may be without affecting other factors or the outcome of a process. This can be by the use of scientific principles, engineering knowledge, and professional experience. Experimental investigation is very useful to investigate the effects of tolerances: Design of experiments, formal engineering evaluations, etc.
A good set of engineering tolerances in a specification, by itself, does not imply that compliance with those tolerances will be achieved. Actual production of any product (or operation of any system) involves some inherent variation of input and output. Measurement error and statistical uncertainty are also present in all measurements. With a normal distribution, the tails of measured values may extend well beyond plus and minus three standard deviations from the process average. One, or both, tails might extend beyond the specified tolerance.
The process capability of systems, materials, and products needs to be compatible with the specified engineering tolerances. Process controls must be in place and an effective Quality management system, such as Total Quality Management, needs to keep actual production within the desired tolerances. A process capability index is used to indicate the relationship between tolerances and actual measured production.
The choice of tolerances is also affected by the intended statistical sampling plan and its characteristics such as the Acceptable Quality Level. This relates to the question of whether tolerances must be extremely rigid (high confidence in 100% conformance) or whether some small percentage of being out-of-tolerance may sometimes be acceptable.
An alternative view of tolerances
Genichi Taguchi and others have suggested that traditional two-sided tolerancing is analogous to "goal posts" in a football game: It implies that all data within those tolerances are equally acceptable. The alternative is that the best product has a measurement which is precisely on target. There is an increasing loss which is a function of the deviation or variability from the target value of any design parameter. The greater the deviation from target, the greater is the loss. This is described as the Taguchi loss function or "quality loss function", and it is the key principle of an alternative system called "inertial tolerancing".
Research and development work conducted by M. Pillet and colleagues at the Savoy University has resulted in industry-specific adoption. Recently, the publishing of the French standard NFX 04-008 has allowed further consideration by the manufacturing community.
Mechanical component tolerance
Dimensional tolerance is related to, but different from fit in mechanical engineering, which is a designed-in clearance or interference between two parts. Tolerances can be applied to any dimension. The commonly used terms are:
- Basic size: the nominal diameter of the shaft (or bolt) and the hole. This is, in general, the same for both components.
- Lower deviation: the difference between the basic size and the minimum possible component size.
- Upper deviation: the difference between the basic size and the maximum possible component size.
- Fundamental deviation: the minimum difference in size between a component and the basic size. This is identical to the upper deviation for shafts and the lower deviation for holes. If the fundamental deviation is greater than zero, the bolt will always be smaller than the basic size and the hole will always be wider. Fundamental deviation is a form of allowance, rather than tolerance.
- International Tolerance grade: this is a standardised measure of the maximum difference in size between the component and the basic size (see below).
For example, if a shaft with a nominal diameter of 10 mm is to have a sliding fit within a hole, the shaft might be specified with a tolerance range from 9.964 to 10 mm (i.e. a zero fundamental deviation, but a lower deviation of 0.036 mm) and the hole might be specified with a tolerance range from 10.04 mm to 10.076 mm (0.04 mm fundamental deviation and 0.076 mm upper deviation). This would provide a clearance fit of somewhere between 0.04 mm (largest shaft paired with the smallest hole, called the "maximum material condition") and 0.112 mm (smallest shaft paired with the largest hole). In this case the size of the tolerance range for both the shaft and hole is chosen to be the same (0.036 mm), meaning that both components have the same International Tolerance grade but this need not be the case in general.
1 decimal place (.x): ±0.2 2 decimal places (.0x): ±0.01 3 decimal places (.00x): ±0.005 4 decimal places (.000x): ±0.0005
International Tolerance grades
When designing mechanical components, a system of standardized tolerances called International Tolerance grades are often used. The standard (size) tolerances are divided into two categories: hole and shaft. They are labelled with a letter (capitals for holes and lowercase for shafts) and a number. For example: H7 (hole tapped hole or nut) and h7 (shaft or bolt). H7/h6 is a very common standard tolerance which gives a rather tight fit, but not so tight that you can't put the shaft in the hole, or turn the nut on the bolt, by hand. The tolerances work in such a way that for a hole H7 means that the hole should be made slightly larger than the base dimension (in this case for an ISO fit 10+0.015−0, meaning that it may be up to 0.015 mm larger than the base dimension, and 0 mm smaller). The actual amount bigger/smaller depends on the base dimension. For a shaft of the same size h6 would mean 10+0−0.009, which is the opposite of H7. This method of standard tolerances is also known as Limits and Fits and can be found in ISO 286-1:2010 (Link to ISO catalog).
The table below summarises the International Tolerance (IT) grades and the general applications of these grades:
Measuring Tools Material IT Grade 01 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 Fits Large Manufacturing Tolerances
An analysis of fit by Statistical interference is also extremely useful: It indicates the frequency (or probability) of parts properly fitting together.
Electrical component tolerance
An electrical specification might call for a resistor with a nominal value of 100 Ω (ohms), but will also state a tolerance such as "±1%". This means that any resistor with a value in the range 99 Ω to 101 Ω is acceptable. For critical components, one might specify that the actual resistance must remain within tolerance within a specified temperature range, over a specified lifetime, and so on.
Many commercially available resistors and capacitors of standard types, and some small inductors, are often marked with coloured bands to indicate their value and the tolerance. High-precision components of non-standard values may have numerical information printed on them.
Difference between allowance and tolerance
The terms are often confused but sometimes a difference is maintained. See Allowance (engineering)#Confounding of the engineering concepts of allowance and tolerance.
- ^ Pillet M., Adragna P-A., Germain F., Inertial Tolerancing: "The Sorting Problem", Journal of Machine Engineering : Manufacturing Accuracy Increasing Problems, optimization, Vol. 6, No. 1, 2006, pp. 95-102.
- ^ Thesis Quality Control and Inertial Tolerancing in the watchmaking industry, in french
- ^ 2, 3 and 4 decimal places quoted from page 29 of "Machine Tool Practices", 6th edition, by R.R.; Kibbe, J.E.; Neely, R.O.; Meyer & W.T.; White, ISBN 0-13-270232-0, 2nd printing, copyright 1999, 1995, 1991, 1987, 1982 and 1979 by Prentice Hall.
(All four places, including the single decimal place, are common knowledge in the field, although a reference for the single place could not be found.)
- ^ According to Chris McCauley, Editor-In-Chief of Industrial Press' Machinery's Handbook: Standard Tolerance "...does not appear to originate with any of the recent editions (24-28) of Machinery's Handbook, although those tolerances may have been mentioned somewhere in one of the many old editions of the Handbook." (4/24/2009 8:47 AM)
- Pyzdek, T, "Quality Engineering Handbook", 2003, ISBN 0824746147
- Godfrey, A. B., "Juran's Quality Handbook", 1999, ISBN 007034003
- ASTM D4356 Standard Practice for Establishing Consistent Test Method Tolerances
Wikimedia Foundation. 2010.
Look at other dictionaries:
Tolerance (disambiguation) — Tolerance may refer to:* Tolerance, a virtue or value * Religious tolerance, tolerance toward different religions * Physiological tolerance, a resistance to the effects of a substance after repeated exposure * Drug tolerance, tolerance occurring… … Wikipedia
Tolerance stacks — Tolerance Analysis is the general term for all activities related to the study of accumulated variation in mechanical parts and assemblies, and may be used on other types of systems subject to accumulated variation, such as mechanical electrical… … Wikipedia
Engineering ethics — is the field of applied ethics which examines and sets standards for engineers obligations to the public, their clients, employers and the profession. This article addresses the subject for both professional engineers and other… … Wikipedia
Engineering drawing — Technical drawings An engineering drawing, a type of technical drawing, is used to fully and clearly define requirements for engineered items. Engineering drawing (the activity) produces engineering drawings (the documents). More than just the… … Wikipedia
Engineering fit — Fit refers to the mating of two mechanical components. Manufactured parts are very frequently required to mate with one another. They may be designed to slide freely against one another or they may be designed to bind together to form a single… … Wikipedia
Parallels (engineering) — Engineering parallels are rectangular blocks of metal, commonly tool steel, stainless steel or cast iron, which have 4 or 6 faces ground or lapped to a precise surface finish. They are used when machining with a miller, drill or any other… … Wikipedia
Allowance (engineering) — In engineering and machining, an allowance is a planned deviation between an actual dimension and a nominal or theoretical dimension, or between an intermediate stage dimension and an intended final dimension. The unifying abstract concept is… … Wikipedia
Damage tolerance — is a property of a structure relating to its ability to sustain defects safely until repair can be effected. The approach to engineering design to account for damage tolerance is based on the assumption that flaws can exist in any structure and… … Wikipedia
Safety engineering — is an applied science strongly related to systems engineering and the subset System Safety Engineering. Safety engineering assures that a life critical system behaves as needed even when pieces fail.In the real world the term safety engineering… … Wikipedia
Topic outline of engineering — For a more comprehensive list, see the List of engineering topics. Engineering is the practice and method of applying scientific and empirical knowledge to the service of humanity, and is distinct from the physical sciences, which are studies of… … Wikipedia