Vacuum flange


Vacuum flange
A KF-25 tee, o-ring, and clamp.

A vacuum flange is a flange at the end of a tube used to connect vacuum chambers, tubing and vacuum pumps to each other.

Contents

Vacuum flange types

A CF (conflat) pipe and flange with copper gasket.

Several vacuum flange standards exist, and the same flange types are called by different names by different manufacturers and standards organizations.

KF/QF

The ISO standard quick release flange is known by the names Quick Flange (QF), Klein Flange (KF) or NW, sometimes also as DN.[1] The KF designation has been adopted by ISO, DIN, and Pneurop. KF flanges are made with a chamferred back surface that attached with a circular clamp and an elastomeric o-ring that is mounted in a metal centering ring. Standard sizes are indicated by the nominal inner diameter in millimeters for flanges 16 through 50 mm in diameter.[2]

  • DN16KF
  • DN25KF
  • DN40KF
  • DN50KF

ISO

The ISO large flange standard is known as LF, LFB, MF or sometimes just ISO flange. As in KF-flanges, the flanges are joined by a centering ring and an elastomeric o-ring. An extra spring-loaded circular clamp is often used around the large diameter o-rings to prevent them from rolling off from the centering ring during mounting.

The ISO large flanges come in two varieties. The ISO-K (or ISO LF) flanges are joined with double claw clamps which clamp to a circular groove on the tubing side of the flange. The ISO-F (or ISO LFB) flanges have holes for attaching the two flanges with bolts. Two tubes with ISO-K and ISO-F flanges can be joined together by clamping the ISO-K side with single claw clamps which are then bolted to the holes on the ISO-F side.

ISO large flanges are available in sizes from 63 to 500 mm nominal tube diameter).[2]

  • DN63LF (63.5 mm)
  • DN100LF (102 mm)
  • DN160LF (160 mm)
  • DN200LF (200 mm)
  • DN250LF (254 mm)
  • DN320LF (316 mm)
  • DN400LF (400 mm)
  • DN500LF (500 mm)

CF (Conflat)

CF (ConFlat) flanges use a copper gasket and knife-edge flange to achieve an ultrahigh vacuum seal.[3] The term "ConFlat" is a registered trademark of Varian, Inc., so "CF" is commonly used by other flange manufacturers. Each face of the two mating CF flanges has a knife edge which cuts into the softer metal gasket, providing an extremely leak-tight, metal-to-metal seal. Deformation of the metal gasket fills small defects in the flange, allowing Conflat flanges operate down to 10−13 torr (10−11 Pa) pressure. The gasket is partially recessed in a groove in each flange. The groove helps hold the gasket in place, which aligns the two flanges and also reduces gasket expansion during bake-out.[4] For stainless steel conflat flanges baking temperatures of 450°C can be achieved; the temperature is limited by the choice of gasket material. CF flanges are sexless and interchangeable. North American flange sizes are given by flange outer diameter in inches while in Europe and Asia, sizes are given by tube inner diameter in millimeters:

European, Asian size North American size [inches]
DN10 1
DN16 1⅓ ("mini")
DN25 2⅛
DN40 (or: DN35)
DN50 3⅜
DN63
DN75 4⅝
DN100 6
DN125
DN160 (or: DN150) 8
DN200 10
DN250 12
  13¼
  14
  16½
A 60 kV high voltage electrical feedthrough on a 4-1/2 inch (or DN63) conflat flange

ConFlat gaskets were originally invented by William Wheeler and other engineers at Varian in an attempt to build a flange that would not leak after baking.[5]

Wheeler

A Wheeler flange is a large wire seal flange often used on large vacuum chambers.[6]

ASA

ANSI has a flange standard called ASA.[7] These flanges are elastomeric o-ring seal and can be used for both vacuum and pressure applications. Flange sizes are indicated by tube nominal inner diameter or by flange outer diameter (in inches): 1 (4.25 O.D.), 1.5 (5.00 O.D.), 2 (6.00 O.D.), 3 (7.50 O.D.), 4 (9.00 O.D.), 6 (11.00 O.D.), 8 (13.5 O.D.), 10 (16.00 O.D.).

Vacuum gaskets

To achieve a vacuum seal, a gasket is required. An elastomeric o-ring gasket can be made of Buna rubber, viton fluoropolymer, silicon rubber or teflon. O-rings can be placed in a groove or may be used in combination with a centering ring or as a "captured" o-ring that is held in place by separate metal rings. Metal gaskets are used in ultra-high vacuum systems where the outgassing of the elastomer could be a significant gas load. A copper ring gasket is used with conflat flanges. Metal wire gaskets made of copper, gold or indium can be used.

Vacuum feedthrough

A vacuum feedthrough is a flange that contains a vacuum-tight electrical, physical or mechanical connection to the vacuum chamber. An electrical feedthrough allows voltages to be applied to components under vacuum, for example a filament or heater. An example of a physical feedthrough is a vacuum tight connection for cooling water. A mechanical feedthrough is used for rotation and translation of components under vacuum. A wobble stick is a mechanical feedthrough device that can be used to pick up, move and otherwise manipulate objects in the vacuum chamber.

See also

References

External links


Wikimedia Foundation. 2010.

Look at other dictionaries:

  • high-vacuum flange — didžiavakuumė jungė statusas T sritis radioelektronika atitikmenys: angl. high vacuum flange vok. Hochvakuumflansch, m rus. высоковакуумный фланец, m pranc. bride sous vide élevé, f …   Radioelektronikos terminų žodynas

  • Vacuum engineering — deals with technological processes and equipment that use vacuum to achieve better results than those run under atmospheric pressure. The most widespread applications of vacuum technology are: * Pyrolytic Chromium Carbide Coating * Antireflecting …   Wikipedia

  • Flange — A flange is an external or internal rib, or rim (lip), for strength, as the flange of an iron beam or I beam (or a T beam); or for a guide, as the flange of a train wheel; or for attachment to another object, as the flange on the end of a pipe,… …   Wikipedia

  • Vacuum — This article is about empty physical space or the absence of matter. For other uses, see Vacuum (disambiguation). Free space redirects here. For other uses, see Free space (disambiguation). Pump to demonstrate vacuum In everyday usage, vacuum is… …   Wikipedia

  • Vacuum pump — A vacuum pump is a device that removes gas molecules from a sealed volume in order to leave behind a partial vacuum. The vacuum pump was invented in 1650 by Otto von Guericke. Types Pumps can be broadly categorized according to three… …   Wikipedia

  • Vacuum chamber — A vacuum chamber is a rigid enclosure from which air and other gases are removed by a vacuum pump. The resulting low pressure, commonly referred to as a vacuum, allows researchers to conduct physical experiments or to test mechanical devices… …   Wikipedia

  • Flange (disambiguation) — A flange is a rib or rim.Flange may also refer to: * Flanging, an audio effect *A collective noun for baboons. [ [http://www.askoxford.com/asktheexperts/collective/b/?view=uk AskOxford: B ] ] The word flange was used by Rowan Atkinson in a sketch …   Wikipedia

  • Vacuum gauge — Gauge Gauge, n. [Written also gage.] 1. A measure; a standard of measure; an instrument to determine dimensions, distance, or capacity; a standard. [1913 Webster] This plate must be a gauge to file your worm and groove to equal breadth by. Moxon …   The Collaborative International Dictionary of English

  • Ultra high vacuum — (UHV) is the vacuum regime characterised by pressures lower than about 10−7 pascal or 100 nanopascals ( 10−9 torr). UHV requires the use of special materials in creating the vacuum system, extreme cleanliness to maintain the vacuum system, and… …   Wikipedia

  • Gasket — [ thumb|sright|250px|Some seals and gaskets 1. o ring 2. fiber washer 3. paper gaskets 4. cylinder head gasket] A gasket is a mechanical seal that fills the space between two objects, generally to prevent leakage between the two objects while… …   Wikipedia


We are using cookies for the best presentation of our site. Continuing to use this site, you agree with this.