 Bicycle performance

A bicycle's performance, in both biological and mechanical terms, is extraordinarily efficient. In terms of the amount of energy a person must expend to travel a given distance, investigators have calculated it to be the most efficient selfpowered means of transportation.^{[1]} From a mechanical viewpoint, up to 99% of the energy delivered by the rider into the pedals is transmitted to the wheels, although the use of gearing mechanisms may reduce this by 10–15%.^{[2]}^{[3]} In terms of the ratio of cargo weight a bicycle can carry to total weight, it is also a most efficient means of cargo transportation.
Contents
Energy efficiency
A human being traveling on a bicycle at low to medium speeds of around 10–15 mph (16–24 km/h), using only the power required to walk, is the most energyefficient means of transport generally available.^{[citation needed]} Air drag, which increases roughly with the square of speed,^{[4]} requires increasingly higher power outputs relative to speed, power increasing with the cube of speed as power equals force times velocity. A bicycle in which the rider lies in a supine position is referred to as a recumbent bicycle or, if covered in an aerodynamic fairing to achieve very low air drag, as a streamliner.
On firm, flat, ground, a 70 kg person requires about 30 watts to walk at 5 km/h. That same person on a bicycle, on the same ground, with the same power output, can average 15 km/h, so energy expenditure in terms of kcal/(kg·km) is roughly onethird as much. Generally used figures are
 1.62 kJ/(km∙kg) or 0.28 kcal/(mi∙lb) for cycling,
 3.78 kJ/(km∙kg) or 0.653 kcal/(mi∙lb) for walking/running,
 16.96 kJ/(km∙kg) or 2.93 kcal/(mi∙lb) for swimming.
Amateur bicycle racers can typically produce 3 watts/kg for more than an hour (e.g., around 210 watts for a 70 kg rider), with top amateurs producing 5 W/kg and elite athletes achieving 6 W/kg for similar lengths of time. Elite track sprinters are able to attain an instantaneous maximum output of around 2,000 watts, or in excess of 25 W/kg; elite road cyclists may produce 1,600 to 1,700 watts as an instantaneous maximum in their burst to the finish line at the end of a fivehour long road race. Even at moderate speeds, most power is spent in overcoming the aerodynamic drag force, which increases with the square of speed.^{[4]} Thus, the power required to overcome drag increases with the cube of the speed.
Typical speeds
Typical speeds for bicycles are 15 to 30 km/h (10 to 20 mph). On a fast racing bicycle, a reasonably fit rider can ride at 50 km/h (30 mph) on flat ground for short periods. The highest speed officially recorded for any humanpowered vehicle (HPV) on level ground and with calm winds and without external aids (such as motor pacing and windblocks) is 133.284 km/h (82.819 mph). That record was set in 2009 by Sam Whittingham in the Varna.^{[5]} In the 1989 Race Across America, a group of HPV's crossed the United States in just 6 days.^{[6]}^{[7]}^{[8]}^{[9]} The highest speed officially recorded for a bicycle ridden in a conventional upright position under fully faired conditions was 82.52 km/h (51.29 mph) over 200m.^{[10]}^{[11]} That record was set in 1986 by Jim Glover on a Moulton AM7 at the 3rd international HPV scientific symposium at Vancouver.
Weight vs power
There has been major corporate competition to lower the weight of racing bikes through the use of advanced materials and components. Additionally, advanced wheels are available with lowfriction bearings and other features to lower resistance, however in measured tests these components have almost no effect on cycling performance when riding on flat ground. For instance, lowering a bike's weight by 1 lb (0.45 kg), a major effort considering it may weigh less than 15 lb (6.8 kg) to start with, will have the same effect over a 40 km time trial on flat ground as removing a protrusion into the air the size of a pencil. Also, the UCI sets a limit on the minimum weight of bicycles to be used in sanctioned races,^{[12]} to discourage making structures so thin that they become unsafe. For these reasons recent designs have concentrated on lowering wind resistance by using aerodynamically shaped tubing, flat spokes on the wheels, and handlebars that position the rider's torso and arms for minimal drag. These changes can impact performance dramatically, cutting minutes off a time trial. Less weight results in larger time savings on uphill terrain.
Kinetic energy of a rotating wheel
Consider the kinetic energy and "rotating mass" of a bicycle in order to examine the energy impacts of rotating versus nonrotating mass.
The translational kinetic energy of an object in motion is:^{[13]}
 ,
Where E is energy in joules, m is mass in kg, and v is velocity in meters per second. For a rotating mass (such as a wheel), the rotational kinetic energy is given by
 ,
where I is the moment of inertia, ω (pronunciation: omega) is the angular velocity in radians per second. For a wheel with all its mass at the outer edge (a fair approximation for a bicycle wheel), the moment of inertia is
 I = mr^{2}.
Where r is the radius in meters
The angular velocity is related to the translational velocity and the radius of the tire. As long as there is no slipping,
 .
When a rotating mass is moving down the road, its total kinetic energy is the sum of its translational kinetic energy and its rotational kinetic energy:
Substituting for I and ω, we get
The r^{2} terms cancel, and we finally get
 .
In other words, a mass on the tire has twice the kinetic energy of a nonrotating mass on the bike. There is a kernel of truth in the old saying that "A pound off the wheels = 2 pounds off the frame."^{[14]}
This all depends, of course, on how well a thin hoop approximates the bicycle wheel. In reality, all the mass cannot be at the radius. For comparison, the opposite extreme might be a disk wheel where the mass is distributed evenly throughout the interior. In this case and so the resulting total kinetic energy becomes . A pound off the disk wheels = only 1.5 pounds off the frame. Most real bicycle wheels will be somewhere between these two extremes.
One other interesting point from this equation is that for a bicycle wheel that is not slipping, the kinetic energy is independent of wheel radius. In other words, the advantage of 650C or other smaller wheels is due to their lower weight (less material in a smaller circumference) rather than their smaller diameter, as is often stated. The KE for other rotating masses on the bike is tiny compared to that of the wheels. For example, pedals turn at about the speed of wheels, so their KE is about (per unit weight) that of a spinning wheel. As their center of mass turns on a smaller radius, this is further reduced.
Convert to kilocalories
Assuming that a rotating wheel can be treated as the mass of rim and tire and 2/3 of the mass of the spokes, all at the center of the rim/tire. For a 180 lb (82 kg) rider on an 18 lb (8 kg) bike (90 kg total) at 25 mph (40 km/h ; 11.2 m/s), the KE is 5625 joules for the bike/rider plus 94 joules for a rotating wheel (combined 1.5 kg of rims/tires/spokes). Converting joules to kilocalories (multiply by 0.0002389) gives 1.4 kilocalories (large calories, nutritional calories, or Calories with a capital "C").
That 1.4 kilocalories is the energy necessary to accelerate from a standstill, or the heat to be dissipated by the brakes to stop the bike. These are kilocalories, so 1.4 kilocalories will heat 1 kg of water 1.4 degrees Celsius. Since aluminum's heat capacity is 21% of water, this amount of energy would heat 800 g of alloy rims 8 °C (15 °F) in a rapid stop. Rims do not get very hot from stopping on flat ground. To get the rider's energy expenditure, consider the 24% efficiency factor to get 5.8 kilocalories—accelerating a bike/rider to 25 mph (40 km/h) requires about 0.5% of the energy required to ride at 25 mph (40 km/h) for an hour. This energy expenditure would take place in about 15 seconds, at a rate of roughly 0.4 kilocalories per second, while steady state riding at 25 mph (40 km/h) requires 0.3 kilocalories per second.
Advantages of light wheels
The advantage of light bikes, and particularly light wheels, from a KE standpoint is that KE only comes into play when speed changes, and there are certainly two cases where lighter wheels should have an advantage: sprints, and corner jumps in a criterium.^{[15]}
In a 250 m sprint from 36 to 47 km/h to (22 to 29 mph), a 90 kg bike/rider with 1.75 kg of rims/tires/spokes increases KE by 6,360 joules (6.4 kilocalories burned). Shaving 500 g from the rims/tires/spokes reduces this KE by 35 joules (1 kilocalorie = 1.163 watthour). The impact of this weight saving on speed or distance is rather difficult to calculate, and requires assumptions about rider power output and sprint distance. The Analytic Cycling web site allows this calculation, and gives a time/distance advantage of 0.16 s/188 cm for a sprinter who shaves 500 g off their wheels. If that weight went to make an aero wheel that was worth 0.03 mph (0.05 km/h) at 25 mph (40 km/h), the weight savings would be canceled by the aerodynamic advantage. For reference, the best aero bicycle wheels are worth about 0.4 mph (0.6 km/h) at 25, and so in this sprint would handily beat a set of wheels weighing 500 g less.
In a criterium race, a rider is often jumping out of every corner. If the rider has to brake entering each corner (no coasting to slow down), then the KE that is added in each jump is wasted as heat in braking. For a flat crit at 40 km/h, 1 km circuit, 4 corners per lap, 10 km/h speed loss at each corner, one hour duration, 80 kg rider/6.5 kg bike/1.75 kg rims/tires/spokes, there would be 160 corner jumps. This effort adds 387 kilocalories to the 1100 kilocalories required for the same ride at steady speed. Removing 500 g from the wheels, reduces the total body energy requirement by 4.4 kilocalories. If the extra 500 g in the wheels had resulted in a 0.3% reduction in aerodynamic drag factor (worth a 0.02 mph (0.03 km/h) speed increase at 25 mph), the caloric cost of the added weight effect would be canceled by the reduced work to overcome the wind.
Another place where light wheels are claimed to have great advantage is in climbing. Though one may hear expressions such as "these wheels were worth 1–2 mph", etc. The formula for power suggests that 1 lb saved is worth 0.06 mph (0.1 km/h) on a 7% grade, and even a 4 lb saving is worth only 0.25 mph (0.4 km/h) for a light rider. So, where is the big savings in wheel weight reduction coming from? One argument is that there is no such improvement; that it is "placebo effect". But it has been proposed that the speed variation with each pedal stroke when riding up a hill explains such an advantage. However the energy of speed variation is conserved; during the power phase of pedaling the bike speeds up slightly, which stores KE, and in the "dead spot" at the top of the pedal stroke the bike slows down, which recovers that KE. Thus increased rotating mass may slightly reduce speed variations, but it does not add energy requirement beyond that of the same nonrotating mass.
Lighter bikes are easier to get up hills, but the cost of "rotating mass" is only an issue during a rapid acceleration, and it is small even then.
Explanations
Possible technical explanations for the widely claimed benefits of light components in general, and light wheels in particular, is as follows:
 Light weight wins races with significant climbing because the heavier bike can't make up the gap on descents or on the flats: the rider on the lighter bike just drafts. Alternatively, if the identical riders of heavier and lighter bikes simultaneously reach the bottom of a climb to the finish, all of the advantage goes to the lighter bike. This is not the case in a hilly time trials (or riding solo), where the advantage of heavier, but more aerodynamic wheels would easily make up the distance lost in climbs.^{[citation needed]}
 Light weight wins sprints because it accelerates more easily. But note that heavier aerodynamic wheels gain significant advantage as speed increases, and for a good part of a sprint a rider is doing little accelerating but is working hard against a highspeed wind. So many sprint situations may favor heavier but more aerodynamic wheels.^{[citation needed]}
 Light weight wins in criteriums because of the constant acceleration out of every corner. Heavier but more aerodynamic wheels offer little advantage because the riders are in a group most of the time. The energy savings from lighter wheels is minimal, but it may be more significant that the leg muscles have to put out just that bit of extra effort at each jam.^{[citation needed]}
There are two "nontechnical" explanations for the effects of light weight. First is the placebo effect. Since the rider feels that they are on better (lighter) equipment, they push themselves harder and therefore go faster. It's not the equipment that increases speed so much as the rider's belief and resulting higher power output. The second nontechnical explanation is the triumph of hope over experience—the rider is not much faster due to lightweight equipment but thinks they are faster. Sometimes this is due to lack of real data, as when a rider took two hours to do a climb on their old bike and on their new bike did it in 1:50. No accounting for how fit the rider was during these two climbs, how hot or windy it was, which way the wind was blowing, how the rider felt that day, etc.
Another explanation, of course, may be marketing benefits associated with selling weight reductions.
In the end, the "incremental muscle power requirement" argument is the only one that can support the claimed advantages of light wheels in "jump" situations. This argument would state that: if the rider is already at the limit on each jump or each stroke of the pedals, then the small amount of extra power required for the extra weight would be a significant physiologic burden. Whether this is true is not clear, but it is the only explanation for the claimed advantage of wheel weight savings (compared to saving weight from the rest of the bike). For these accelerations, it makes no difference whether 1 lb is taken off the wheels or 2 lb off the bike/rider. The miracle of light wheels (compared to saving weight anywhere else in the bike/rider system) is hard to see.
Aerodynamics vs power
Heated debates over the relative importance of weight savings and aerodynamics are a fixture in cycling. This is an attempt to at least get the equationbased parts of the debate clarified. There will always be those who argue that "experience trumps mathematics" on this issue, so this will attempt to highlight those areas where experience might disagree with the math. From this, perhaps further discussion can focus on the topics of dispute rather than questioning known physics. To be as clear as possible, this will cover 1) the power requirements for moving a bike/rider, 2) the energy cost of acceleration, and then 3) why experience and the math might disagree.
Power required
There is a wellknown equation that gives the power required to push a bike and rider through the air and to overcome the friction of the drive train:
Where P is in watts, g is Earth's gravity, V_{g} is ground speed (m/s), m is bike/rider mass in kg, s is the grade (m/m), and V_{a} is the rider's speed through the air (m/s). K_{1} is a lumped constant for all frictional losses (tires, bearings, chain), and is generally reported with a value of 0.0053. K_{2} is a lumped constant for aerodynamic drag and is generally reported with a value of 0.185 kg/m.^{[16]}
Note that the power required to overcome friction and gravity is proportional only to rider weight and ground speed. The aerodynamic drag is roughly proportional to the square of the relative velocity of the air and the bike. Being that the total power requirement to propel the bike forward is a sum of these two variables multiplied by speed, the degree of proportionality between power requirement and speed varies according to their relative magnitude, in an interval between the linear and cube: at higher speeds (riding fast on a flat road) power required will be close to being a cube function of speed, at lower speeds (climbing a steep hill) it will be close to being a linear function of speed.
The human body runs at about 24% efficiency for a relatively fit athlete, so for every kilojoule delivered to the pedals the body consumes 1 kcal (4.2 kJ) of food energy.^{[citation needed]}
Obviously, both of the lumped constants in this equation depend on many variables, including drive train efficiency, the rider's position and drag area, aerodynamic equipment, tire pressure, and road surface. Also, recognize that air speed is not constant in speed or direction or easily measured. It is certainly reasonable that the aerodynamic lumped constant would be different in cross winds or tail winds than in direct head winds, as the profile the bike/rider presents to the wind is different in each situation. Also, wind speed as seen by the bike/rider is not uniform except in zero wind conditions. Weather report wind speed is measured at some distance above the ground in free air with no obstructing trees or buildings nearby. Yet, by definition, the wind speed is always zero right at the road surface. Assuming a single wind velocity and a single lumped drag constant are just two of the simplifying assumptions of this equation. Computational fluid dynamicists have looked at this bicycle modeling problem and found it hard to model well. In layman's terms, this means that much more sophisticated models can be developed, but they will still have simplifying assumptions.
Given this simplified equation, however, one can calculate some values of interest. For example, assuming no wind, one gets the following results for kilocalories required and power delivered to the pedals (watts):
 175 W for a 90 kg bike + rider to go 9 m/s (20 mph or 32 km/h) on the flats (76% of effort to overcome aerodynamic drag), or 2.6 m/s (5.8 mph or 9.4 km/h) on a 7% grade (21% of effort to overcome aerodynamic drag).
 300 W for a 90 kg bike + rider at 11 m/s (25 mph or 40 km/h) on the flats (83% of effort to overcome aerodynamic drag) or 4.3 m/s (9.5 mph or 15 km/h) on a 7% grade (42% of effort to overcome aerodynamic drag).
 165 W for a 65 kg bike + rider to go 9 m/s (20 mph or 32 km/h) on the flats (82% of effort to overcome aerodynamic drag), or 3.3 m/s (7.4 mph or 12 km/h) on a 7% grade (37% of effort to overcome aerodynamic drag).
 285 W for a 65 kg bike + rider at 11 m/s (25 mph or 40 km/h) on the flats (87% of effort to overcome aerodynamic drag) or 5.3 m/s (12 mph or 19 km/h) on a 7% grade (61% of effort to overcome aerodynamic drag).
Shaving 1 kg off the weight of the bike/rider would increase speed by 0.01 m/s at 9 m/s on the flats (5 seconds in a 20 mph (32 km/h), 25mile (40 km) TT). Losing 1 kg on a 7% grade would be worth 0.04 m/s (90 kg bike + rider) to 0.07 m/s (65 kg bike + rider). If one climbed for 1 hour, saving 1 lb would gain between 225 and 350 feet (107 m) – less effect for the heavier bike + rider combination (e.g., 0.04 mph (0.06 km/h) * 1 h * 5,280 ft (1,609 m)/mi = 225 ft). For reference, the big climbs in the Tour de France have the following average grades:
 Tourmalet = 7%
 Galibier = 7.5%
 Alpe D'Huez = 8.6%^{[17]}
 Mont Ventoux = 7.1%.
The equation can be separated into level ground power
 ,
and vertical climbing power given by
 .
Energy cost of acceleration
See also
References
 ^ S.S. Wilson (March 1973). "Bicycle Technology". Scientific American.
 ^ Phil Sneiderman Homewood (August 30, 1999). "Pedal Power Probe Shows Bicycles Waste Little Energy". Johns Hopkins Gazette. http://www.jhu.edu/~gazette/1999/aug3099/30pedal.html. Retrieved 20100221.
 ^ Wilson, David Gordon; Jim Papadopoulos (2004). Bicycling Science (Third ed.). The MIT Press. p. 318. ISBN 0262731541. "When new, clean, and welllubricated, and when sprockets with a minimum of 21 teeth are used, a chain transmission is highly efficient (at a level of maybe 98.5 percent or even higher)."
 ^ ^{a} ^{b} Wilson, David Gordon; Jim Papadopoulos (2004). Bicycling Science (Third ed.). The MIT Press. p. 126. ISBN 0262731541. "aerodynamic drag force is proportional to the square of the velocity"
 ^ http://www.wisil.recumbents.com/wisil/whpsc2009/results.htm
 ^ Wired.com. "World's Fastest Cyclist Hits 82.3 MPH". http://blog.wired.com/cars/2008/09/worldsfastest.html. Retrieved 20080926.
 ^ "International Human Powered Vehicle Association Official Speed Records". http://www.ihpva.org/hpva/hpvarec3.html#nom01. Retrieved 20080304.
 ^ "Fastest Human Powered Lists". http://www.wisil.recumbents.com/wisil/fastest_list.asp. Retrieved 20080304.
 ^ "HPV And Bicycle Speed Records Men – Single Rider". http://www.legslarry.beerdrinkers.co.uk/tech/MLS.htm. Retrieved 20080304.
 ^ "Moulton Bicycle Company: Records and Racing". http://www.moultonbicycles.co.uk/heritage.html#recordsracing. Retrieved 20100226.
 ^ "Aerodynamic research using the Moulton smallwheeled bicycle". http://pep.metapress.com/content/l323nr7267358864/. Retrieved 20100226.
 ^ uci.ch. "UCI Rules". http://www.uci.ch/templates/UCI/UCI2/layout.asp?MenuId=MTkzNg. Retrieved 20100727.
 ^ Ruina, Andy; Rudra Pratap (2002) (PDF). Introduction to Statics and Dynamics. Oxford University Press. p. 397. http://ruina.tam.cornell.edu/Book/RuinaPratapNoProblems.pdf. Retrieved 20060804.
 ^ "Wheels and the Myth about Rotating Weight". http://www.charles.whitaker.name/wheels.html. Retrieved 20070203.
 ^ "Technical Q&A with Lennard Zinn: The great rotatingweight debate". Archived from the original on 20061017. http://web.archive.org/web/20061017095411/http://www.velonews.com/tech/report/articles/9662.0.html. Retrieved 20070203.
 ^ Corresponding to a surface area of 0.4m^2 with a drag coefficient of 0.7: Drag (physics)#Power
 ^ Sastre wins the 2008 L'Alpe d'Huez stage. July 23, 2008. p. Velo News. http://www.velonews.com/article/80615. Retrieved 20090114.
Categories:
Wikimedia Foundation. 2010.
Look at other dictionaries:
Bicycle wheel — For the Marcel Duchamp installation, see Bicycle Wheel. The front wheel from a racing bicycle made using a Mavic rim … Wikipedia
Bicycle — For other uses, see Bicycle (disambiguation). A mountain bike, a popular multi use bicycle. A bicycle, also known as a bike, pushbike or cycle, is a human powered, pedal driven, single track vehicle, having two wheels attached to a frame, one… … Wikipedia
Bicycle suspension — refers to the system or systems used to suspend the rider and all or part of the bicycle in order to protect them from the roughness of the terrain over which they travel. Bicycle suspension are used primarily on mountain bicycles, but are also… … Wikipedia
Bicycle brake systems — are used to slow down, or brake a bicycle. There have been various types through history, and several are still in use today.HistoryEarly bicycles such as the high wheeled penny farthing bikes were fitted with spoon brakes. As they were fixed… … Wikipedia
Bicycle lighting — has two purposes: seeing and being seen. There are many types of bicycle lights available, each with its own advantages and disadvantages. There is no one best solution for any rider, and many riders mix and match different technologies to… … Wikipedia
Bicyclefriendly — describes policies and practices which may help some people feel more comfortable about traveling by bicycle with other traffic. The level of bicycle friendliness of an environment can be influenced my many factors resulting from town planning… … Wikipedia
Bicycle race — Single par Queen extrait de l’album Jazz Face A Bicycle Race Face B Fat Bottomed Girls Sortie 13 octobre 1978 Enregistrement … Wikipédia en Français
Bicycle Race — Single par Queen extrait de l’album Jazz Face A Bicycle Race Face B Fat Bottomed Girls Sortie 13 octobre 1978 … Wikipédia en Français
Bicycle Quarterly — is a quarterly magazine that examines the history of bicycles, their design, and evolution. Articles regularly and rigorously evaluate equipment and bicycles for performance and function. All articles are footnoted. Bicycle Quarterly was formerly … Wikipedia
Bicycle brake — Animation of a single pivot side pull calliper brake for the rear wheel of a steel framed road bike. A bicycle brake is used to slow down or stop a bicycle. There have been various types of brake used throughout history, and several are still in… … Wikipedia