Electrical impedance

Electrical impedance
A graphical representation of the complex impedance plane

Electrical impedance, or simply impedance, is the measure of the opposition that an electrical circuit presents to the passage of a current when a voltage is applied. In quantitative terms, it is the complex ratio of the voltage to the current in an alternating current (AC) circuit. Impedance extends the concept of resistance to AC circuits, and possesses both magnitude and phase, unlike resistance which has only magnitude. When a circuit is driven with direct current (DC), there is no distinction between impedance and resistance; the latter can be thought of as impedance with zero phase angle.

It is necessary to introduce the concept of impedance in AC circuits because there are other mechanisms impeding the flow of current besides the normal resistance of DC circuits. There are an additional two impeding mechanisms to be taken into account in AC circuits: the induction of voltages in conductors self-induced by the magnetic fields of currents (inductance), and the electrostatic storage of charge induced by voltages between conductors (capacitance). The impedance caused by these two effects is collectively referred to as reactance and forms the imaginary part of complex impedance whereas resistance forms the real part.

The symbol for impedance is usually \scriptstyle Z and it may be represented by writing its magnitude and phase in the form \scriptstyle  |Z| \angle \theta . However, complex number representation is often more powerful for circuit analysis purposes. The term impedance was coined by Oliver Heaviside in July 1886.[1][2] Arthur Kennelly was the first to represent impedance with complex numbers in 1893.[3]

Impedance is defined as the frequency domain ratio of the voltage to the current.[4] In other words, it is the voltage–current ratio for a single complex exponential at a particular frequency ω. In general, impedance will be a complex number, with the same units as resistance, for which the SI unit is the ohm (Ω). For a sinusoidal current or voltage input, the polar form of the complex impedance relates the amplitude and phase of the voltage and current. In particular,

  • The magnitude of the complex impedance is the ratio of the voltage amplitude to the current amplitude.
  • The phase of the complex impedance is the phase shift by which the current is ahead of the voltage.

The reciprocal of impedance is admittance (i.e., admittance is the current-to-voltage ratio, and it conventionally carries units of siemens, formerly called mhos).

Contents

Complex impedance

Impedance is represented as a complex quantity \scriptstyle Z and the term complex impedance may be used interchangeably; the polar form conveniently captures both magnitude and phase characteristics,

\ Z = |Z| e^{j\theta} \quad

where the magnitude \scriptstyle |Z| represents the ratio of the voltage difference amplitude to the current amplitude, while the argument \scriptstyle \theta gives the phase difference between voltage and current and \scriptstyle j is the imaginary unit. In Cartesian form,

\ Z = R + jX \quad

where the real part of impedance is the resistance \scriptstyle R and the imaginary part is the reactance \scriptstyle X.

Where it is required to add or subtract impedances the cartesian form is more convenient, but when quantities are multiplied or divided the calculation becomes simpler if the polar form is used. A circuit calculation, such as finding the total impedance of two impedances in parallel, may require conversion between forms several times during the calculation. Conversion between the forms follows the normal conversion rules of complex numbers.

Ohm's law

An AC supply applying a voltage \scriptstyle V, across a load \scriptstyle Z, driving a current \scriptstyle I.

The meaning of electrical impedance can be understood by substituting it into Ohm's law.[5][6]

\ V = I Z = I |Z| e^{j\theta} \quad

The magnitude of the impedance \scriptstyle |Z| acts just like resistance, giving the drop in voltage amplitude across an impedance \scriptstyle Z for a given current \scriptstyle I. The phase factor tells us that the current lags the voltage by a phase of \scriptstyle \theta (i.e. in the time domain, the current signal is shifted \scriptstyle \frac{\theta}{2 \pi} T later with respect to the voltage signal).

Just as impedance extends Ohm's law to cover AC circuits, other results from DC circuit analysis such as voltage division, current division, Thevenin's theorem, and Norton's theorem, can also be extended to AC circuits by replacing resistance with impedance.

Complex voltage and current

Generalized impedances in a circuit can be drawn with the same symbol as a resistor (US ANSI or DIN Euro) or with a labeled box.

In order to simplify calculations, sinusoidal voltage and current waves are commonly represented as complex-valued functions of time denoted as \scriptstyle V and \scriptstyle I.[7][8]

\ V = |V|e^{j(\omega t + \phi_V)}
\ I = |I|e^{j(\omega t + \phi_I)}

Impedance is defined as the ratio of these quantities.

\ Z = \frac{V}{I}

Substituting these into Ohm's law we have


\begin{align}
  |V| e^{j(\omega t + \phi_V)} &= |I| e^{j(\omega t + \phi_I)} |Z| e^{j\theta}    \\
                              &= |I| |Z| e^{j(\omega t + \phi_I + \theta)}
\end{align}

Noting that this must hold for all t, we may equate the magnitudes and phases to obtain

\ |V| = |I| |Z| \quad
\ \phi_V = \phi_I + \theta \quad

The magnitude equation is the familiar Ohm's law applied to the voltage and current amplitudes, while the second equation defines the phase relationship.

Validity of complex representation

This representation using complex exponentials may be justified by noting that (by Euler's formula):

\ \cos(\omega t + \phi) = \frac{1}{2} \Big[ e^{j(\omega t + \phi)} + e^{-j(\omega t + \phi)}\Big]

i.e. a real-valued sinusoidal function (which may represent our voltage or current waveform) may be broken into two complex-valued functions. By the principle of superposition, we may analyse the behaviour of the sinusoid on the left-hand side by analysing the behaviour of the two complex terms on the right-hand side. Given the symmetry, we only need to perform the analysis for one right-hand term; the results will be identical for the other. At the end of any calculation, we may return to real-valued sinusoids by further noting that

\ \cos(\omega t + \phi) = \Re \Big\{ e^{j(\omega t + \phi)} \Big\}

In other words, we simply take the real part of the result.

Phasors

A phasor is a constant complex number, usually expressed in exponential form, representing the complex amplitude (magnitude and phase) of a sinusoidal function of time. Phasors are used by electrical engineers to simplify computations involving sinusoids, where they can often reduce a differential equation problem to an algebraic one.

The impedance of a circuit element can be defined as the ratio of the phasor voltage across the element to the phasor current through the element, as determined by the relative amplitudes and phases of the voltage and current. This is identical to the definition from Ohm's law given above, recognising that the factors of \scriptstyle e^{j\omega t} cancel.

Device examples

The phase angles in the equations for the impedance of inductors and capacitors indicate that the voltage across a capacitor lags the current through it by a phase of π / 2, while the voltage across an inductor leads the current through it by π / 2. The identical voltage and current amplitudes tell us that the magnitude of the impedance is equal to one.

The impedance of an ideal resistor is purely real and is referred to as a resistive impedance:

\ Z_R = R.

In this case the voltage and current waveforms are proportional and in phase.

Ideal inductors and capacitors have a purely imaginary reactive impedance:

\ Z_L = j\omega L,

the impedance of inductors increases with frequency;

\ Z_C = \frac{1}{j\omega C},

the impedance of capacitors decreases with frequency.

In both cases, for an applied sinusoidal voltage, the resulting current is also sinusoidal, but in quadrature, 90 degrees out of phase with the voltage. However the phases have opposite signs: in an inductor, the current is lagging; in a capacitor the current is leading.

Note the following identities for the imaginary unit and its reciprocal:

j = \cos{\left(\frac{\pi}{2}\right)} + j\sin{\left(\frac{\pi}{2}\right)} = e^{j\frac{\pi}{2}},
\frac{1}{j} = -j = \cos{\left(-\frac{\pi}{2}\right)} + j\sin{\left(-\frac{\pi}{2}\right)} = e^{j(-\frac{\pi}{2})}.

Thus we can rewrite the inductor and capacitor impedance equations in polar form:

\ Z_L = \omega Le^{j\frac{\pi}{2}},
\ Z_C = \frac{1}{\omega C}e^{j(-\frac{\pi}{2})}.

The magnitude tells us the change in voltage amplitude for a given current amplitude through the impedance, while the exponential factors give the phase relationship.

Deriving the device specific impedances

What follows below is a derivation of impedance for each of the three basic circuit elements, the resistor, the capacitor, and the inductor. Although the idea can be extended to define the relationship between the voltage and current of any arbitrary signal, these derivations will assume sinusoidal signals, since any arbitrary signal can be approximated as a sum of sinusoids through Fourier Analysis.

Resistor

For a resistor, we have the relation:

v_{\text{R}} \left( t \right) = {i_{\text{R}} \left( t \right)}R.

This is simply a statement of Ohm's Law.

Considering the voltage signal to be

v_{\text{R}}(t) = V_p \sin(\omega t) \, ,

it follows that

\frac{v_{\text{R}} \left( t \right)}{i_{\text{R}} \left( t \right)} = \frac{V_p \sin(\omega t)}{I_p \sin \left( \omega  t \right)} = R.

This tells us that the ratio of AC voltage amplitude to AC current amplitude across a resistor is \scriptstyle R, and that the AC voltage leads the AC current across a resistor by 0 degrees.

This result is commonly expressed as

Z_{\text{resistor}} = R \, .

Capacitor

For a capacitor, we have the relation:

i_{\text{C}}(t) = C \frac{\operatorname{d}v_{\text{C}}(t)}{\operatorname{d}t}.

Considering the voltage signal to be

v_{\text{C}}(t) = V_p \sin(\omega t) \,

it follows that

\frac{\operatorname{d}v_{\text{C}}(t)}{\operatorname{d}t} = \omega  V_p \cos \left( \omega  t \right).

And thus

\frac{v_{\text{C}} \left( t \right)}{i_{\text{C}} \left( t \right)} = \frac{V_p \sin(\omega t)}{\omega V_p C \cos \left( \omega  t \right)}= \frac{\sin(\omega t)}{\omega C \sin \left( \omega  t + \frac{\pi}{2}\right)}.

This tells us that the ratio of AC voltage amplitude to AC current amplitude across a capacitor is \scriptstyle \frac{1}{\omega C}, and that the AC voltage lags the AC current across a capacitor by -90 degrees (or the AC current leads the AC voltage across a capacitor by 90 degrees).

This result is commonly expressed in polar form, as

\ Z_{\text{capacitor}} = \frac{1}{\omega C} e^{-j \frac{\pi}{2}}

or, by applying Euler's formula, as

\ Z_{\text{capacitor}} = -j\frac{1}{\omega C} = \frac{1}{j \omega C} \, .

Inductor

For the inductor, we have the relation:

v_{\text{L}}(t) = L \frac{\operatorname{d}i_{\text{L}}(t)}{\operatorname{d}t}.

This time, considering the current signal to be

i_{\text{L}}(t) = I_p \sin(\omega t) \, ,

it follows that

\frac{\operatorname{d}i_{\text{L}}(t)}{\operatorname{d}t} = \omega  I_p \cos \left( \omega  t \right).

And thus

\frac{v_{\text{L}} \left( t \right)}{i_{\text{L}} \left( t \right)} = \frac{\omega I_p L \cos(\omega t)}{I_p \sin \left( \omega  t \right)}= \frac{\omega L \sin \left( \omega  t + \frac{\pi}{2}\right)}{\sin(\omega t)}.

This tells us that the ratio of AC voltage amplitude to AC current amplitude across an inductor is \scriptstyle \omega L, and that the AC voltage leads the AC current across an inductor by 90 degrees.

This result is commonly expressed in polar form, as

\ Z_{\text{inductor}} = \omega L e^{j \frac{\pi}{2}} .

Or, more simply, using Euler's formula, as

\ Z_{\text{inductor}} = j \omega L. \,

Generalised s-plane impedance

Impedance defined in terms of can strictly only be applied to circuits which are energised with a steady-state AC signal. The concept of impedance can be extended to a circuit energised with any arbitrary signal by using complex frequency instead of . Complex frequency is given the symbol s and is, in general, a complex number. Signals are expressed in terms of complex frequency by taking the Laplace transform of the time domain expression of the signal. The impedance of the basic circuit elements in this more general notation is as follows:

Element Impedance expression
Resistor R \,
Inductor sL \,
Capacitor \frac{1}{sC} \,

For a DC circuit this simplifies to s = 0. For a steady-state sinusoidal AC signal s = .

Resistance vs reactance

Resistance and reactance together determine the magnitude and phase of the impedance through the following relations:

|Z| = \sqrt{Z Z^*} = \sqrt{R^2 + X^2}
\theta = \arctan{\left(\frac{X}{R}\right)}

In many applications the relative phase of the voltage and current is not critical so only the magnitude of the impedance is significant.

Resistance

Resistance \scriptstyle R is the real part of impedance; a device with a purely resistive impedance exhibits no phase shift between the voltage and current.

\ R = |Z| \cos{\theta} \quad

Reactance

Reactance \scriptstyle X is the imaginary part of the impedance; a component with a finite reactance induces a phase shift \scriptstyle \theta between the voltage across it and the current through it.

\ X = |Z| \sin{\theta}  \quad

A purely reactive component is distinguished by the fact that the sinusoidal voltage across the component is in quadrature with the sinusoidal current through the component. This implies that the component alternately absorbs energy from the circuit and then returns energy to the circuit. A pure reactance will not dissipate any power.

Capacitive reactance

A capacitor has a purely reactive impedance which is inversely proportional to the signal frequency. A capacitor consists of two conductors separated by an insulator, also known as a dielectric.

X_C = -(\omega C)^{-1} = -(2\pi f C)^{-1}\quad

At low frequencies a capacitor is open circuit, as no charge flows in the dielectric. A DC voltage applied across a capacitor causes charge to accumulate on one side; the electric field due to the accumulated charge is the source of the opposition to the current. When the potential associated with the charge exactly balances the applied voltage, the current goes to zero.

Driven by an AC supply, a capacitor will only accumulate a limited amount of charge before the potential difference changes sign and the charge dissipates. The higher the frequency, the less charge will accumulate and the smaller the opposition to the current.

Inductive reactance

Inductive reactance \scriptstyle{X_L} is proportional to the signal frequency \scriptstyle{f} and the inductance \scriptstyle{L}.

X_L = \omega L = 2\pi f L\quad

An inductor consists of a coiled conductor. Faraday's law of electromagnetic induction gives the back emf \scriptstyle{\mathcal{E}} (voltage opposing current) due to a rate-of-change of magnetic flux density \scriptstyle{B} through a current loop.

\mathcal{E} = -{{d\Phi_B} \over dt}\quad

For an inductor consisting of a coil with N loops this gives.

\mathcal{E} = -N{d\Phi_B \over dt}\quad

The back-emf is the source of the opposition to current flow. A constant direct current has a zero rate-of-change, and sees an inductor as a short-circuit (it is typically made from a material with a low resistivity). An alternating current has a time-averaged rate-of-change that is proportional to frequency, this causes the increase in inductive reactance with frequency.

Combining impedances

The total impedance of many simple networks of components can be calculated using the rules for combining impedances in series and parallel. The rules are identical to those used for combining resistances, except that the numbers in general will be complex numbers. In the general case however, equivalent impedance transforms in addition to series and parallel will be required.

Series combination

For components connected in series, the current through each circuit element is the same; the total impedance is simply the sum of the component impedances.

Impedances in series.svg

\ Z_{\text{eq}} = Z_1 + Z_2 + \cdots + Z_n \quad

Or explicitly in real and imaginary terms:

\ Z_{\text{eq}} = R + jX = (R_1 + R_2 + \cdots + R_n) + j(X_1 + X_2 + \cdots + X_n) \quad

Parallel combination

For components connected in parallel, the voltage across each circuit element is the same; the ratio of currents through any two elements is the inverse ratio of their impedances.

Impedances in parallel.svg

Hence the inverse total impedance is the sum of the inverses of the component impedances:

\frac{1}{Z_{\text{eq}}} = \frac{1}{Z_1} + \frac{1}{Z_2} + \cdots + \frac{1}{Z_n}\,

or, when n = 2:

Z_{\text{eq}} = Z_1 \| Z_2 \,\stackrel{\text{def}}{=}\,  \frac{Z_1 Z_2}{Z_1 + Z_2} \quad

The equivalent impedance \scriptstyle Z_{\text{eq}} can be calculated in terms of the equivalent resistance \scriptstyle R_{\text{eq}} and reactance \scriptstyle X_{\text{eq}}.[9]

\ Z_{\text{eq}} = R_{\text{eq}} + j X_{\text{eq}} \quad
R_{\text{eq}} = \frac{(X_1 R_2 + X_2 R_1) (X_1 + X_2) + (R_1 R_2 - X_1 X_2) (R_1 + R_2)}{(R_1 + R_2)^2 + (X_1 + X_2)^2}
X_{\text{eq}} = \frac{(X_1 R_2 + X_2 R_1) (R_1 + R_2) - (R_1 R_2 - X_1 X_2) (X_1 + X_2)}{(R_1 + R_2)^2 + (X_1 + X_2)^2}

Measurement

The impedance of a device can be calculated by complex division of the voltage and current. The impedance of the device can be calculated by applying a sinusoidal voltage to the device in series with a resistor, and measuring the voltage across the resistor and across the device. Performing this measurement by sweeping the frequencies of the applied signal provides the impedance phase and magnitude.[10]

Impulse impedance spectroscopy

The use of an impulse response may be used in combination with the fast Fourier transform (FFT) to rapidly measure the electrical impedance of various electrical devices. The technique compares well to other methodologies such as network and impedance analyzers while providing additional versatility in the electrical impedance measurement. The technique is theoretically simple, easy to implement and completed with ordinary laboratory instrumentation for minimal cost.[10]

Variable impedance

In general, neither impedance nor admittance can be time varying as they are defined for complex exponentials for –∞ < t < +∞. If the complex exponential voltage–current ratio changes over time or amplitude, the circuit element cannot be described using the frequency domain. However, many systems (e.g., varicaps that are used in radio tuners) may exhibit non-linear or time-varying voltage–current ratios that appear to be LTI for small signals over small observation windows; hence, they can be roughly described as having a time-varying impedance. That is, this description is an approximation; over large signal swings or observation windows, the voltage–current relationship is non-LTI and cannot be described by impedance.

See also

References

  1. ^ Science, p. 18, 1888
  2. ^ Oliver Heaviside, The Electrician, p. 212, 23 July 1886, reprinted as Electrical Papers, p 64, AMS Bookstore, ISBN 0821834657
  3. ^ Kennelly, Arthur. Impedance (AIEE, 1893)
  4. ^ Alexander, Charles; Sadiku, Matthew (2006). Fundamentals of Electric Circuits (3, revised ed.). McGraw-Hill. pp. 387–389. ISBN 9780073301150 
  5. ^ AC Ohm's law, Hyperphysics
  6. ^ Horowitz, Paul; Hill, Winfield (1989). "1". The Art of Electronics. Cambridge University Press. pp. 32–33. ISBN 0-521-37095-7. 
  7. ^ Complex impedance, Hyperphysics
  8. ^ Horowitz, Paul; Hill, Winfield (1989). "1". The Art of Electronics. Cambridge University Press. pp. 31–32. ISBN 0-521-37095-7. 
  9. ^ Parallel Impedance Expressions, Hyperphysics
  10. ^ a b Lewis Jr., George; George K. Lewis Sr. and William Olbricht (August 2008). "Cost-effective broad-band electrical impedance spectroscopy measurement circuit and signal analysis for piezo-materials and ultrasound transducers". Measurement Science and Technology 19 (10): 105102. Bibcode 2008MeScT..19j5102L. doi:10.1088/0957-0233/19/10/105102. PMC 2600501. PMID 19081773. http://www.iop.org/EJ/abstract/0957-0233/19/10/105102/. Retrieved 2008-09-15. 

External links


Wikimedia Foundation. 2010.

Игры ⚽ Нужен реферат?

Look at other dictionaries:

  • Electrical impedance tomography — (EIT), is a medical imaging technique in which an image of the conductivity or permittivity of part of the body is inferred from surface electrical measurements. Typically conducting electrodes are attached to the skin of the subject and small… …   Wikipedia

  • electrical impedance tomography — elektrinės varžos tomografija statusas T sritis Standartizacija ir metrologija apibrėžtis Laidžių sluoksnių elektrinės varžos pasiskirstymo apskaičiavimo būdas, pagrįstas rekonstrukcinių algoritmų taikymu per bandinį pratekėjusioms srovėms ir jo… …   Penkiakalbis aiškinamasis metrologijos terminų žodynas

  • electrical impedance — Opposition that a circuit presents to electric current. It includes both resistance and reactance. Resistance arises from collisions of the current carrying charged particles with the internal structure of the conductor. Reactance is an… …   Universalium

  • Impedance cardiography — (ICG) is a hemorheology technique of using sensors to detect the properties of the blood flow in the Thorax.IntroductionImpedance cardiography (ICG), also referred to as thoracic electrical bioimpedance (TEB) and electrical impedance… …   Wikipedia

  • Impedance — is a concept associated with the transmission of waves and electrical signals. There are many kinds of waves, and impedance is different in each of them, hence this disambiguation page. However, impedance is also a unifying concept. It is related …   Wikipedia

  • Electrical resistance — is a ratio of the degree to which an object opposes an electric current through it, measured in Ohms. Its reciprocal quantity is electrical conductance measured in Siemens. Assuming a uniform current density, an object s electrical resistance is… …   Wikipedia

  • Electrical conductivity — or specific conductivity is a measure of a material s ability to conduct an electric current. When an electrical potential difference is placed across a conductor, its movable charges flow, giving rise to an electric current. The conductivity σ… …   Wikipedia

  • Electrical resistivity tomography — (ERT) or electrical resistivity imaging (ERI) is a geophysical technique for imaging sub surfaces structures from electrical measurements made at the surface, or by electrodes in one or more boreholes. It is closely related to the medical imaging …   Wikipedia

  • Electrical capacitance tomography — (ECT) is a method for determination of the dielectric permittivity distribution in the interior of an object from external capacitance measurements. It is a close relative of electrical impedance tomography [ M Soleimani, W R B Lionheart,… …   Wikipedia

  • Impedance matching — In electronics, impedance matching is the practice of designing the input impedance of an electrical load (or the output impedance of its corresponding signal source) to maximize the power transfer and/or minimize reflections from the load.… …   Wikipedia

Share the article and excerpts

Direct link
Do a right-click on the link above
and select “Copy Link”