T-carrier


T-carrier

In telecommunications, T-carrier, sometimes abbreviated as "T-CXR", is the generic designator for any of several digitally multiplexed telecommunications carrier systems originally developed by Bell Labs and used in North America, Japan, and Korea.

The basic unit of the T-carrier system is the DS0, which has a transmission rate of 64 kbit/s, and is commonly used for one voice circuit.

The E-carrier system, where 'E' stands for European, is incompatible with the T-carrier and is used at most places in the world outside of North America, Japan, and Korea. It typically uses the E1 line rate and the E3 line rate. The E2 line rate is less commonly used. See the table below for bit rate comparisons.

T1

Existing Frequency-division multiplexing carrier systems worked well for connections between distant cities, but required expensive modulators, demodulators and filters for every voice channel. For connections within metropolitan areas, Bell Labs in the late 1950s sought cheaper terminal equipment. Pulse-code modulation allowed sharing a coder and decoder among several voice trunks, so this method was chosen for the T1 system introduced into local use in 1961. In later decades, the cost of digital electronics declined to the point that an individual codec per voice channel became commonplace, but by then the other advantages of digital transmission had become entrenched.

The most common legacy of this system is the line rate speeds. "T1" now seems to mean any data circuit that runs at the original 1.544 Mbit/s line rate. Originally the T1 format carried 24 pulse-code modulated, time-division multiplexed speech signals each encoded in 64 kbit/s streams, leaving 8 kbit/s of framing information which facilitates the synchronization and demultiplexing at the receiver. T2 and T3 circuit channels carry multiple T1 channels multiplexed, resulting in transmission rates of 6.312 and 44.736 Mbit/s, respectively.

Supposedly, the 1.544 Mbit/s rate was chosen because tests done by AT&T Long Lines in Chicago were conducted underground. To accommodate loading coils, cable vault manholes were physically 6600 feet apart, and so the optimum bit rate was chosen empirically--the capacity was increased until the failure rate was unacceptable, then reduced to leave a margin. Companding allowed acceptable audio performance with only seven bits per PCM sample in this original T1/D1 system. The later D3 and D4 channel banks had an extended frame format, allowing eight bits per sample, reduced to seven every sixth sample or frame when one bit was "robbed" for signaling the state of the channel. The standard does not allow an all zero sample which would produce a long string of binary zeros and cause the repeaters to lose bit sync. However, when carrying data (Switched 56) there could be long strings of zeroes, so one bit per sample is set to "1" (jam bit 7) leaving 7 bits x 8000 frames per second for data.

A more common understanding of how the rate of 1.544 Mbit/s was achieved is as follows. (This explanation glosses over T1 voice communications, and deals mainly with the numbers involved.) Given that the highest voice frequency which the telephone system transmits is 4000 Hz, the required digital sampling rate is 8000 Hz (see Nyquist rate). Since each T1 frame contains 1 byte of voice data for each of the 24 channels, that system needs then 8000 frames per second to maintain those 24 simultaneous voice channels. Because each frame of a T1 is 193 bits in length (24 channels X 8 bits per channel + 1 framing bit = 193 bits), 8000 frames per second is multiplied by 193 bits to yield a transfer rate of 1.544 Mbit/s (8000 X 193 = 1544000).

Initially, T1 used Alternate Mark Inversion (AMI) to reduce frequency bandwidth and eliminate the DC component of the signal. Later B8ZS became common practice. For AMI, each mark pulse had the opposite polarity of the previous one and each space was at a level of zero, resulting in a three level signal which however only carried binary data. Similar British 23 channel systems at 1.536 Mbaud in the 1970s were equipped with ternary signal repeaters, in anticipation of using a 3B2T or 4B3T code to increase the number of voice channels in future, but in the 1980s the systems were merely replaced with European standard ones. American T-carriers could only work in AMI or B8ZS mode.

The AMI or B8ZS signal allowed a simple error rate measurement. The D bank in the central office could detect a bit with the wrong polarity, or "bipolarity violation" and sound an alarm. Later systems could count the number of violations and reframes and otherwise measure signal quality.

Historical Note on the 193-bit T1 frame

The decision to use a 193-bit frame was made in 1958, during the early stages of T1 system design. To allow for the identification of information bits within a frame, two alternatives were considered. Assign (a) just one extra bit, or (b) additional 8 bits per frame. The 8-bit choice is cleaner, resulting in a 200-bit frame, 25 8-bit channels, of which 24 are traffic and 1 8-bit channel available for operations, administration, and maintenance (OA&M). AT&T chose the single bit per frame not to reduce the required bit rate (1.544 vs 1.6 Mbit/s), but because AT&T Marketing worried that "if 8 bits were chosen for OA&M function, someone would then try to sell this as a voice channel and you wind up with nothing."

Soon after commercial success of T1 in 1962, the T1 engineering team realized the mistake of having only one bit to serve the increasing demand for housekeeping functions. They petitioned AT&T management to change to 8-bit framing. This was flatly turned down because it would make installed systems obsolete.

Having this hindsight, some ten years later, CEPT chose 8 bits for framing the European E1.

Higher T

In the late 1960s and early 1970s Bell Labs developed higher rate systems. T-1C with a more sophisticated modulation scheme carried 3 Mbit/s, on those balanced pair cables that could support it. T-2 carried 6.312 Mbit/s, requiring a special low-capacitance cable with foam insulation. This was standard for Picturephone. T-4 and T-5 used coaxial cables, similar to the old L-carriers used by AT&T Long Lines. TD microwave radio relay systems were also fitted with high rate modems to allow them to carry a DS1 signal in a portion of their FM spectrum that had too poor quality for voice service. Later they carried DS3 and DS4 signals. Later optical fiber, typically using SONET transmission scheme, overtook them.

Digital signal crossconnect

DS1 signals are interconnected typically at Central Office locations at a common metallic cross-connect point known as a DSX-1. A DS1 signal at a DSX-1 is measured typically at 6 Volts Peak-to-peak (0dBdsx signal level at 772 kHz Nyquist) at plus or minus 1.2 volts to permit easy interconnection of DS1 equipment NCI Code=04DS9/ /). When a DS1 is transported over metallic outside plant cable, the signal travels over conditioned cable pairs known as a T1 span. A T1 span can have up to -130 Volts of DC power superimposed on the associated four wire cable pairs to line or "Span" power line repeaters, and T1 NIU's (T1 Smartjacks). T1 span repeaters are typically engineered up to 6000 feet apart, depending on cable gauge, and at no more than 36 dB of loss before requiring a repeated span. There can be no cable bridge taps across any pairs.

T1 copper spans are being replaced by optical transport systems, but if a copper (Metallic) span is used, the T1 is typically carried over an HDSL encoded copper line. Four wire HDSL does not require as many repeaters as conventional T1 spans. Newer two wire HDSL (HDSL-2) equipment transports a full 1.54400Bp/s T1 over a single copper wire pair up to approximately twelve thousand (12,000) feet (3.5 km), if all 24 gauge cable is used. HDSL-2 does not employ repeaters as does conventional four wire HDSL, or newer HDSL-4 systems.

One advantage of HDSL is its ability to operate with a limited number of bridge taps, with no tap being closer than 500 feet from any HDSL transceiver. Both two or four wire HDSL equipment transmits and receives over the same cable wire pair, as compared to conventional T1 service that utilizes individual cable pairs for transit or receive.

DS3 signals are rare except within buildings, where they are used for interconnections and as an intermediate step before being muxed onto a SONET circuit. This is because a T3 circuit can only go about 600 feet(180m) between repeaters. A customer who orders a DS3 usually receives a SONET circuit run into the building and a multiplexer mounted in a utility box. The DS3 is delivered in its familiar form, two coax cables (1 for send and 1 for receive) with BNC connectors on the ends.

Reference: ANSI T1.403//ANSI T1.231//ANSI T1.404//ANSI T1.510.

Bit robbing

T1 carrier can utilize out-of-band (Robbed Bit) signalling, as opposed to earlier forms of in-band circuit signaling that utilized in-band audio tones typically at 2600 Hz, and more commonly known as SF signaling. In robbed bit signaling, the eighth bit, which is the least significant bit in the eight bit PCM sample that comprises the T1 carrier DS0 channel, is used to carry T1 channel signaling information.

Twelve DS1 frames make up a single T1 Superframe (T1 SF). Each T1 Superframe is comprised of two signaling frames. All T1 DS0 channels that employ in-band signaling will have its eighth bit over written, or "robbed", from the full 64Kb/s DS0 payload, and be overwritten by either a logical ZERO or ONE bit to signify a circuit signaling state or condition. Hence robbed bit signaling only will restrict a DS0 channel to a 56KB/s rate during two of the twelve DS1 frames that make up a T1 SF framed circuit. T1 SF framed circuits yield two independent signaling channels (A&B) T1 ESF framed circuits four signaling frames in a twenty four frame extended frame format that yield four independent signaling channels (A, B,C,& D).

NOTE: 56KB/s DS0 channels are associated with digital data service (DDS) services typically do not utilize the eighth bit of the DS0 as voice circuits that employ A&B out of band signaling. One exception is Switched 56Kb/s DDS. In DDS, bit eight is used to identify DTE request to send (RTS) condition. With Switched 56 DDS, bit eight is pulsed (Alternately set to logical Zeros and Ones) to transmit two state dial pulse signaling information between a SW56 DDS CSU/DSU, and a digital end office switch.

The incident use of robbed-bit signaling in North America has decreased significantly as a result of Signaling System Seven (SS7) on inter-office dial trunks. With SS7, full the 64KB/s DS0 channel is available for use on a connection, and allows 64KB/s, and 128KB/s ISDN data calls to exist over a switched trunk network connection if the supporting T1 carrier entity is optioned B8ZS (Clear Channel Capable).

REFERENCES: ANSI T1.403//The Book On ESF, Verilink Corporation, 1986//D4 Digital Channel Bank Family, Bell System Technical Journal, Nov 1982.

Carrier pricing

Carriers price DS1 lines in many different ways. However, most boil down to two simple components; local loop (the cost the local incumbent charges to transport the signal from the end user's central office, otherwise known as a CO, to the point of presence, otherwise known as a POP, of the carrier) and the port (the cost to access the telephone network or the Internet through the carrier's network). Typically, the port price is based upon access speed and yearly commitment level while the loop is based on geography. The further the CO and POP, the more the loop cost.

The loop price has several components built into it, including the mileage calculation (performed in V/H coordinates, not standard GPS coordinates) and the telco piece. Each local Bell operating company - namely Verizon, AT&T, and Qwest - charge T-carriers different price per mile rates. Therefore, the price calculation has two distance steps: geomapping and the determination of local price arrangements.

While most carriers utilize a geographic pricing model as described above, some Competitive Local Exchange Carriers (CLECs), such as EarthLink Business Solutions, offer national pricing. Under this DS1 pricing model, a provider charges the same price in every geography it services. National pricing is an outgrowth of increased competition in the T-carrier market space and the commoditization of T-carrier products. [cite web
last = Sweeney
first = Terry
authorlink =
coauthors =
title = T1 Price Drop Means Good Deals For Smart Shoppers
work =
publisher = InformationWeek.com
date = December 25, 2000
url = http://www.informationweek.com/817/teeone.htm
format = HTML
doi =
accessdate = 2008-01-03
] Providers that have adopted a national pricing strategy may experience widely varying margins as their suppliers, the Bell operating companies (e.g., Verizon, AT&T and Qwest), maintain geographic pricing models, albeit at wholesale prices.

For voice DS1 lines, the calculation is mostly the same, except that the port (required for Internet access) is replaced by LDU (otherwise known as Long Distance Usage). Once the price of the loop is determined, only voice-related charges are added to the total. In short, the total price = loop + LDU x minutes used.

Notes

"Note 1:" The designators for T-carrier in the North American digital hierarchy correspond to the designators for the digital signal (DS) level hierarchy.

"Note 2:" T-carrier systems were originally designed to transmit digitized voice signals. Current applications also include digital data transmission.

"Note 3:" Historically, if an "F" precedes the "T", optical fiber cables are utilized at the same rates.

"Note 4:" The North American and Japanese hierarchies are based on multiplexing 24 voice-frequency channels and multiples thereof, whereas the European hierarchy is based on multiplexing 32 voice-frequency channels and multiples thereof. "See table below,."

"Note 5:" Will be directed to this table by certain Network+ books. "See table below,."

"Note 1:" The DS designations are used in connection with the North American hierarchy only. Strictly speaking, a DS1 is the data carried on a T1 circuit, and likewise for a DS3 and a T3, but in practice the terms are used interchangeably.

"Note 2:" There are other data rates in use, e.g., military systems that operate at six and eight times the DS1 rate. At least one manufacturer has a commercial system that operates at 90 Mbit/s, twice the DS3 rate. New systems, which take advantage of the high data rates offered by optical communications links, are also deployed or are under development. Higher data rates are now often achieved by using Synchronous optical networking, SONET or Synchronous digital hierarchy, SDH.

"Note 3:" A DS3 is delivered native on a copper trunk. DS3 may be converted to a fiber run when needing longer distances between termination points. When a DS3 is delivered over fiber it is still an analog type trunk connection at the termination points. When delivering data over an OC3 or greater SONET is used. SONET is much faster and has a much lower bit error rate. Fact|date=May 2007

ee also


* Digital Signal 0 (DS0)
* Digital Signal 1 (DS1)
* DS1 Encoding schemes: B8ZS, HDB3, AMI
* Optical Carrier (OC-n)
* Time-division multiplexing
* Multiplexing
* Plesiochronous Digital Hierarchy
* List of device bandwidths
* Modified AMI code
* E-carrier
* STM-1

References

* ANSI T1.403-1999 - Network and Customer Installation Interface
* Federal Standard 1037C
* [http://www.oreilly.com/catalog/t1survival/chapter/ch05.html T1: A Survival Guide Chapter 5]
* [http://www.cisco.com/univercd/cc/td/doc/product/access/acs_serv/5100_sbd/5100ug/74928.htm#xtocid1: Cisco T1 card documentation]
* [http://www.dcbnet.com/notes/9611t1.html T1 architecture]

External links


Wikimedia Foundation. 2010.

Look at other dictionaries:

  • Carrier language — Carrier Dakeł (ᑕᗸᒡ) Spoken in Canada Region Central Interior of British Columbia Ethnicity Carrier people Nati …   Wikipedia

  • Carrier Air Group — Carrier Air Wing Three (CVW 3) im Februar 2008 an Deck der USS Harry S. Truman (CVN 75). Ein Carrier Air Wing (CVW) oder eine Carrier Air Group ist ein Geschwader von Kampfflugzeugen der US Navy, welches auf einem Flugzeugträger stationiert ist.… …   Deutsch Wikipedia

  • Carrier Strike Group Eleven — crest Active 1 October 2004 to date.[1] …   Wikipedia

  • Carrier Air Wing — Three (CVW 3) im Februar 2008 an Deck der USS Harry S. Truman (CVN 75). Ein Carrier Air Wing (CVW) oder eine Carrier Air Group ist ein Geschwader von Kampfflugzeugen der US Navy, welches auf einem Flugzeugträger stationiert ist. Die Schlagkraft …   Deutsch Wikipedia

  • carrier — car‧ri‧er [ˈkæriə ǁ ər] noun [countable] TRANSPORT ORGANIZATIONS a person or company whose job is to transport goods from one place to another: • national carriers like Pickfords, with their own warehouses and regular clientele • the American… …   Financial and business terms

  • Carrier — has various meanings:In Science (physics, electronics, biology, mathematics, chemistry and other sciences): * Carrier wave, a waveform suitable for modulation by an information bearing signal * Charge carrier, an unbound particle carrying an… …   Wikipedia

  • carrier — car·ri·er n 1: an individual or entity engaged in transporting passengers or goods for hire by land, water, or air; specif: common carrier 2: an insurer that assumes the risks of a policy that it issues to a policyholder Merriam Webster’s… …   Law dictionary

  • carrier — [ karje ] n. m. • quarrier 1284; de 1. carrière ♦ Celui qui exploite une carrière comme entrepreneur ou comme ouvrier. Par appos. Un maître carrier; des ouvriers carriers. ⇒ 2. mineur, tailleur (de pierre). Masse, scie de carrier. ⊗ HOM. Carier.… …   Encyclopédie Universelle

  • Carrier's Case — Carrier s Case, 13 Edw. IV, f. 9, pl. 5 (Star Ch. and Exch. Ch. 1473) was a landmark English court case in property crime law decided in the Star Chamber (also called Anonymous v. The Sheriff of London). The English court adopted the breaking… …   Wikipedia

  • Carrier (surname) — Carrier is a surname, and may refer to:* Corey Carrier (born 1980), American child actor * Darel Carrier (born 1940), American professional basketball player * George F. Carrier (1918 2002), American mathematician and Professor Emeritus at… …   Wikipedia

  • Carrier syllabics — Type abugida Languages Carrier (Dakelh) Creator Adrien Gabriel Morice …   Wikipedia