Phantom circuit

Phantom circuit

In telecommunication and electrical engineering, a phantom circuit is an electrical circuit derived from suitably arranged wires with one or more conductive paths being a circuit in itself and at the same time acting as one conductor of another circuit.

Phantom group

A phantom group is composed of three circuits that are derived from two single-channel circuits to form a "phantom circuit". Here the phantom circuit is a third circuit derived from two suitably arranged pairs of wires, called side circuits, with each pair of wires being a circuit in itself and at the same time acting as one conductor of the third circuit. The "side circuits" within phantom circuits can be coupled to their respective voltage drops by center-tapped transformers, usually called "repeating coils". The center taps are on the line side of the side circuits. Current from the phantom circuit is split evenly by the center taps. This cancels crosstalk from the phantom circuit to the side circuits. Phantom working increased the number of circuits on long distance routes in the early 20th century without putting up more wires. Phantoming declined with the adoption of carrier systems.

It is theoretically possible to create a phantom circuit from two other phantom circuits and so on up in a pyramid with a maximum 2n-1 circuits being derived from n original circuits. However, more than one level of phantoming is usually impractical. Isolation between the phantom circuit and the side circuits relies on accurate balance of the line and transformers. Imperfect balance results in crosstalk between the phantom and side circuits and this effect accumulates as each level of phantoms is added. Even small levels of crosstalk are unacceptable on analogue telecommunications circuits since speech crosstalk is still intelligible down to quite low levels.

Phantom mic powering

Recording and broadcast studios commonly use phantom powering as a means to provide power to microphones. Power may be needed either for a device that requires power such as a pre-amp on an electret microphone or because the mic is a type that intrinsically requires powering such as a condenser microphone. Since the microphone has only one pair of wires the return path for the power has to be provided elswhere. This is usually done via the microphone cable screen.

DC phantom

Simple DC signalling can be achieved on a telecommunications line in a similar way to phantom powering of microphones. A switch connected to the transformer centre-tap at one end of the line can operate a similarly connected relay at the other end. The return path is through the ground connection. This arrangement can be used for remotely controlling equipment.

Carrier circuit phantoms

From the 1950s to around the 1980s, using phantoms on star-quad trunk carrier circuits was a popular method of deriving a high quality broadcast audio circuit. The multiplexed FDM telecommucications carrier system usually did not use the baseband of the cable because it was inconvenient to separate low frequencies with filters. On the other hand, a one-way audio phantom could be formed from the two pairs (go and return signals) making up the star-quad cable.

Unloaded phantom

Unloaded phantom is a phantom configuration of loaded lines (a circuit fitted with loading coils). The idea here is not to create additional circuits. Rather, the purpose is to cancel or greatly reduce the effect of the loading coils fitted to a line. The reason for doing this is that loaded lines have a definite cut-off frequency and it may be desired to equalise the line to a frequency which is higher than this, for example to make a circuit suitable for use by a broadcaster. Ideally, the loading would be removed or reduced for a permanent connection, but this is not feasible for temporary arrangements such as a requirement for outside broadcast. Instead, two circuits in a phantom configuration can be used to greatly reduce the inductance being inserted by the loading coils, and hence the loading effect.It works because the loading coils used on balanced lines have two windings, one for each leg of the circuit. They are both wound on a common core and the windings are so arranged that the magnetic flux induced by both of them is in the same direction. Both windings induce an emf in each other as well as their own self-induction. This effect greatly increases the inductance of the coil and hence its loading effectiveness. By contrast, when the circuit is in the phantom configuration the currents in the two wires of each pair are in the same direction and the magnetic flux is being cancelled. This has precisely the opposite effect and the inductance is greatly reduced.

This configuration is most commonly used on the two pairs of a star-quad cable. It is not so successful with other pairs of wires. The difference in the path of the two pairs can easily destroy the balance and results in crosstalk and interference.

This configuration can also be called "bunched pairs". However, "bunched pairs" can also refer to the straightforward connection of two lines in parallel which is not a phantom circuit and will not reduce the loading.

See also

* Phantom loop

ources and references

* Federal Standard 1037C
* MIL-STD-188

Wikimedia Foundation. 2010.

Look at other dictionaries:

  • Phantom circuit — (Elec.) The equivalent of an additional circuit or wire, in reality not existing, obtained by certain arrangements of real circuits, as in some multiplex telegraph systems. [Webster 1913 Suppl.] …   The Collaborative International Dictionary of English

  • phantom circuit — noun : the equivalent of an additional circuit or wire that in reality does not exist obtained by certain arrangements of real circuits (as in some telephone and multiplex telegraph systems) * * * Elect. a circuit derived from two suitably… …   Useful english dictionary

  • phantom circuit —    Circuit configured so that two pairs of wires can provide three speech paths …   IT glossary of terms, acronyms and abbreviations

  • phantom circuit — Elect. a circuit derived from two suitably arranged pairs of wires, each pair being a circuit (side circuit) and also acting as one half of an additional derived circuit, the entire system providing the capabilities of three circuits while… …   Universalium

  • phantom circuit — noun an arrangement of telegraph or other electric wires equivalent to an extra circuit …   English new terms dictionary

  • Phantom loop — A phantom loop is a suitably arranged electrical network that includes within the number of conductive paths part of the natural environment (which can be at the same time acting as a conductor of another circuit) to complete a… …   Wikipedia

  • phantom — n. & adj. n. 1 a ghost; an apparition; a spectre. 2 a form without substance or reality; a mental illusion. 3 Med. a model of the whole or part of the body used to practise or demonstrate operative or therapeutic methods. adj. merely apparent;… …   Useful english dictionary

  • phantom — phantomlike, adj. /fan teuhm/, n. 1. an apparition or specter. 2. an appearance or illusion without material substance, as a dream image, mirage, or optical illusion. 3. a person or thing of merely illusory power, status, efficacy, etc.: the… …   Universalium

  • Phantom voltage — (sometimes referred to as ghost voltage ) is voltage that appears in an electrical conductor such as a wire, even though the wire is disconnected from an electrical circuit. The term is often used by electricians, and might be seen, eg, when… …   Wikipedia

  • Phantom's Revenge — 40°23′21″N 79°51′58″O / 40.38917, 79.86611 …   Wikipédia en Français

Share the article and excerpts

Direct link
Do a right-click on the link above
and select “Copy Link”

We are using cookies for the best presentation of our site. Continuing to use this site, you agree with this.