 Noise temperature

In electronics, noise temperature is one way of expressing the level of available noise power introduced by a component or source. The power spectral density of the noise is expressed in terms of the temperature (in kelvins) that would produce that level of Johnson–Nyquist noise, thus:
where:
 P is the power (in watts)
 B is the total bandwidth (Hz) over which that noise power is measured
 k_{B} is the Boltzmann constant (1.381×10^{−23} J/K, joules per kelvin)
 T is the noise temperature (K)
Thus the noise temperature is proportional to the power spectral density of the noise, P / B. That is the power that would be absorbed from the component or source by a matched load. Noise temperature is generally a function of frequency, unlike that of an ideal resistor which is simply equal to the actual temperature of the resistor at all frequencies.
Contents
Noise voltage and current
A noisy component may be modelled as a noiseless component in series with a noisy voltage source producing a voltage of v_{n}, or as a noiseless component in parallel with a noisy current source producing a current of i_{n}. This equivalent voltage or current corresponds to the above power spectral density , and would have a mean squared amplitude over a bandwidth B of:
where R is the resistive part of the component's impedance or G is the conductance (real part) of the component's admittance. Speaking of noise temperature therefore offers a fair comparison between components having different impedances rather than specifying the noise voltage and qualifying that number by mentioning the component's resistance. It is also more accessible than speaking of the noise's power spectral density (in watts per hertz) since it is expressed as an ordinary temperature which can be compared to the noise level of an ideal resistor at room temperature (290 K).
Note that one can only speak of the noise temperature of a component or source whose impedance has a substantial (and measurable) resistive component. Thus it doesn't make sense to talk about the noise temperature of a capacitor or of a voltage source. The noise temperature of an amplifier refers to the noise that would be added at the amplifier's input (relative to the input impedance of the amplifier) in order to account for the added noise observed following amplification.
Application to communication systems
A communications system is typically made up of a transmitter, a communications channel, and a receiver. The communications channel may consist of a combination of different physical media, resulting in an electrical signal presented to the receiver. Whatever physical media a channel consists of, the transmitted signal will be attenuated and corrupted with additive noise.^{[1]}
The additive noise in a receiving system can be of thermal origin (thermal noise) or can be from other noisegenerating processes. Most noise processes will have a white spectrum, at least over the bandwidth of interest, identical to that of thermal noise. Since they are indistinguishable, the contributions of all noise sources can be lumped together and regarded as a level of thermal noise. The noise power spectral density generated by all these sources (P / B) can be described by assigning to the noise a temperature T as defined above:^{[2]}
In a wireless communications receiver, the equivalent input noise temperature T_{eq} would equal the sum of two noise temperatures:
 T_{eq} = T_{ant} + T_{sys}
The antenna noise temperature T_{ant} gives the noise power seen at the output of the antenna.^{[3]} The noise temperature of the receiver circuitry T_{sys} represents noise generated by noisy components inside the receiver.
Note that T_{eq} refers not to the noise at the output of the receiver after amplification, but the equivalent input noise power. In other words, the output of the receiver reflects that of a noiseless amplifier whose input had a noise level not of T_{ant} but of T_{eq}. Thus the figure of merit of a communications system is not the noise level at the speaker of a radio, for instance, since that depends on the setting of the receiver's gain. Rather we ask how much noise the receiver added to the original noise level, which is thus given by the factor (1 + T_{sys} / T_{ant}). If a signal is present, then this factor represents the decrease in signal to noise ratio incurred using the receiver system with a noise temperature of T_{sys}.
Noise figure
Main article: Noise figureOne use of noise temperature is in the definition of a system's noise factor or noise figure. The noise factor specifies the increase in noise power (referred to the input of an amplifier) due to a component or system when its input noise temperature is T_{0}.
T_{0} is customarily taken to be room temperature, 290 K.
The noise factor (a linear term) is more often expressed as the noise figure (in decibels) using the conversion:
The noise figure can also be seen as the decrease in signal to noise ratio (SNR) caused by passing a signal through a system if the original signal had a noise temperature of 290 K. This is a common way of expressing the noise contributed by a radio frequency amplifier regardless of the amplifier's gain. For instance, assume an amplifier has a noise temperature 870 K and thus a noise figure of 6 dB. If that amplifier is used to amplify a source having a noise temperature of about room temperature (290 K), as many sources do, then the insertion of that amplifier would reduce the SNR of a signal by 6 dB. This simple relationship is frequently applicable where the source's noise is of thermal origin since a passive transducer will often have a noise temperature similar to 290 K.
However in many cases the input source's noise temperature is much higher, such as an antenna at lower frequencies where atmospheric noise dominates. Then there will be little degradation of the SNR. On the other hand a good satellite dish looking through the atmosphere into space (so that it sees a much lower noise temperature) would have the SNR of a signal degraded by more than 6 dB. In those cases a reference to the amplifier's noise temperature itself, rather than the noise figure defined according to room temperature, is more appropriate.
Noise temperature of an amplifier chain
The noise temperature of an amplifier is commonly measured using the Yfactor method. If there are multiple amplifiers in cascade, the noise temperature of the cascade can be calculated using the Friis equation:^{[4]}
where
 T_{eq} = resulting noise temperature referred to the input
 T_{1} = noise temperature of the first component in the cascade
 T_{2} = noise temperature of the second component in the cascade
 T_{3} = noise temperature of the third component in the cascade
 G_{1} = power gain of the first component in the cascade
 G_{2} = power gain of the second component in the cascade
Therefore the amplifier chain can be modelled as a black box having a gain of and a noise figure given by . In the usual case where the gains of the amplifier's stages are much greater than one, then it can be seen that the noise temperatures of the earlier stages have a much greater influence on the resulting noise temperature than those later in the chain. One can appreciate that the noise introduced by the first stage, for instance, is amplified by all of the stages whereas the noise introduced by later stages undergoes lesser amplification. Another way of looking at it is that the signal applied to a later stage already has a high noise level, due to amplification of noise by the previous stages, so that the noise contribution of that stage to that already amplified signal is of less significance.
This explains why the quality of a preamplifier or RF amplifier is of particular importance in an amplifier chain. In most cases only the noise figure of the first stage need be considered. However one must check that the noise figure of the second stage is not so high (or that the gain of the first stage is so low) that there is SNR degradation due to the second stage anyway. That will be a concern if the noise figure of the first stage plus that stage's gain (in decibels) is not much greater than the noise figure of the second stage.
One corollary of the Friis equation is that an attenuator prior to the first amplifier will degrade the noise figure due to the amplifier. For instance, if stage 1 represents a 6 dB attenuator so that , then . Effectively the noise temperature of the amplifier T_{2} has been quadrupled, in addition to the (smaller) contribution due to the attenuator itself T_{1} (usually room temperature if the attenuator is composed of resistors). An antenna with poor efficiency is an example of this principle, where G_{1} would represent the antenna's efficiency.
References
 ^ Proakis, John G., and Masoud Salehi. Fundamentals of Communication Systems. Upper Saddle River, New Jersey: Prentice Hall, 2005. ISBN 013147135X.
 ^ Skolnik, Merrill I., Radar Handbook (2nd Edition). McGrawHill, 1990. ISBN 9780070579132
 ^ The physical temperature of the antenna generally has little or no effect on T_{ant}
 ^ McClaning, Kevin, and Tom Vito. Radio Receiver Design. Atlanta, GA: Noble Publishing Corporation, 2000. ISBN 188493207X.
Noise (in physics and telecommunications) General Distortion · Noise control · Noise measurement · Noise power · Noise reduction · Noise temperature · Phase distortionNoise in... Class of noise Additive white Gaussian noise (AWGN) · Atmospheric noise · Background noise · Brownian noise · Burst noise · Cosmic noise · Flicker noise · Gaussian noise · Grey noise · Jitter · Johnson–Nyquist noise · Pink noise · Quantization error (or q. noise) · Shot noise · White noiseEngineering terms Ratios Carriertonoise ratio (C/N) · Carriertoreceiver noise density (C/kT) · dBrnC · Eb/N0 (energy per bit to noise density) · Es/N0 (energy per symbol to noise density) · Modulation error ratio (MER) · Signal, noise and distortion (SINAD) · Signaltointerference ratio (S/I) · Signaltonoise ratio (S/N, SNR) · Signal to noise ratio (imaging) · Signaltonoise plus interference (SNIR) · Signaltoquantizationnoise ratio (SQNR)Related topics Categories: Noise
 Electronics terms
 Telecommunications terms
Wikimedia Foundation. 2010.
Look at other dictionaries:
noise temperature — triukšmo temperatūra statusas T sritis automatika atitikmenys: angl. equivalent noise temperature; noise temperature vok. equivalente Rauschtemperatur, f; Rauschtemperatur, f rus. шумовая температура, f pranc. température équivalente de bruit, f … Automatikos terminų žodynas
noise temperature — triukšmo temperatūra statusas T sritis fizika atitikmenys: angl. noise temperature vok. Rauschtemperatur, f rus. шумовая температура, f pranc. température de bruit, f … Fizikos terminų žodynas
noise temperature of a linear twoport network — tiesinio keturpolio triukšmo temperatūra statusas T sritis radioelektronika atitikmenys: angl. noise temperature of a linear two port network vok. Rauschtemperatur linearer Vierpols, f rus. шумовая температура линейного четырёхполюсника, f pranc … Radioelektronikos terminų žodynas
noise temperature of oneport network — dvipolio triukšmo temperatūra statusas T sritis radioelektronika atitikmenys: angl. noise temperature of one port network vok. Zweipolrauschtemperatur, f rus. шумовая температура двухполюсника, f pranc. température de bruit d un monoporte, f … Radioelektronikos terminų žodynas
Antenna noise temperature — In telecommunication, antenna noise temperature is the temperature of a hypothetical resistor at the input of an ideal noise free receiver that would generate the same output noise power per unit bandwidth as that at the antenna output at a… … Wikipedia
Effective input noise temperature — In telecommunications, effective input noise temperature is the source noise temperature in a two port network or amplifier that will result in the same output noise power, when connected to a noise free network or amplifier, as that of the… … Wikipedia
equivalent noise temperature — triukšmo temperatūra statusas T sritis automatika atitikmenys: angl. equivalent noise temperature; noise temperature vok. equivalente Rauschtemperatur, f; Rauschtemperatur, f rus. шумовая температура, f pranc. température équivalente de bruit, f … Automatikos terminų žodynas
equivalent satellite link noise temperature — palydovinės ryšio linijos triukšmo temperatūra statusas T sritis radioelektronika atitikmenys: angl. equivalent satellite link noise temperature vok. äquivalente Rauschtemperatur einer Satellitenfunkverbindung, f rus. эквивалентная шумовая… … Radioelektronikos terminų žodynas
Noise figure — (NF) is a measure of degradation of the signal to noise ratio (SNR), caused by components in a radio frequency (RF) signal chain. The noise figure is defined as the ratio of the output noise power of a device to the portion thereof attributable… … Wikipedia
Noise shaping — is a technique typically used in digital audio, image, and video processing, usually in combination with dithering, as part of the process of quantization or bit depth reduction of a digital signal. Its purpose is to increase the apparent signal… … Wikipedia