Noise-equivalent power

Noise-equivalent power

Noise-equivalent power (NEP) is a measure of the sensitivity of a photodetector or detector system. It is defined as the signal power that gives a signal-to-noise ratio of one in a one hertz output bandwidth.[1] An output bandwidth of one hertz is equivalent to half a second of integration time.[2] The units of NEP are watts per square root hertz. The NEP is equal to the noise spectral density (expressed in units of A / Hz1 / 2 or V / Hz1 / 2) divided by the responsivity (expressed in units of A / W or V / W, respectively).

A smaller NEP corresponds to a more sensitive detector. For example, a detector with an NEP of 10^{-12} W/\sqrt{Hz} can detect a signal power of one picowatt with a signal-to-noise ratio (SNR) of one after one half second of averaging. The SNR improves as the square root of the averaging time, and hence the SNR in this example can be improved to 10 by averaging for 50 seconds.

If the NEP refers to the signal power absorbed in the detector, it is known as the electrical NEP. If instead it refers to the signal power incident on the detector system, it is called the optical NEP. The optical NEP is equal to the electrical NEP divided by the optical coupling efficiency of the detector system.

References and footnotes

  1. ^ P.L. Richards, "Bolometers for infrared and millimeter waves," Journal of Applied Physics 76, 1 (1994), doi:10.1063/1.357128
  2. ^ The factor of one half is explained by the Nyquist–Shannon sampling theorem.

See also


Wikimedia Foundation. 2010.

Игры ⚽ Нужен реферат?

Look at other dictionaries:

  • noise equivalent power — ekvivalentinė triukšmo galia statusas T sritis radioelektronika atitikmenys: angl. noise equivalent power vok. äquivalente Rauschleistung, f rus. эквивалентная мощность шумов, f pranc. puissance équivalente de bruit, f …   Radioelektronikos terminų žodynas

  • Noise-equivalent temperature — (NET) is a measure of the sensitivity of a detector of thermal radiation in the infrared, terahertz or microwave portions of the electromagnetic spectrum. It is the amount of incident signal temperature that would be needed to match the internal… …   Wikipedia

  • Noise equivalent temperature difference — (NETD) is a measure of the sensitivity of a detector of thermal radiation in the infrared, terahertz radiation or microwave radiation parts of the electromagnetic spectrum. It is the scene temperature difference equal to either the internal noise …   Wikipedia

  • Noise temperature — In electronics, noise temperature is one way of expressing the level of available noise power introduced by a component or source. The power spectral density of the noise is expressed in terms of the temperature (in kelvins) that would produce… …   Wikipedia

  • List of noise topics — This is a list of noise topics. Contents 1 Engineering and physics 2 Environmental 3 Noise reduction 4 Music …   Wikipedia

  • Noise figure — (NF) is a measure of degradation of the signal to noise ratio (SNR), caused by components in a radio frequency (RF) signal chain. The noise figure is defined as the ratio of the output noise power of a device to the portion thereof attributable… …   Wikipedia

  • Noise (audio) — Noise in audio, recording, and broadcast systems refers to the residual low level sound (usually hiss and hum) that is heard in quiet periods of a programme. In audio engineering, it can refer either to the acoustic noise from loudspeakers, or to …   Wikipedia

  • Noise shaping — is a technique typically used in digital audio, image, and video processing, usually in combination with dithering, as part of the process of quantization or bit depth reduction of a digital signal. Its purpose is to increase the apparent signal… …   Wikipedia

  • Power line communication — or power line carrier (PLC), also known as power line digital subscriber line (PDSL), mains communication, power line telecom (PLT), power line networking (PLN), or broadband over power lines (BPL) are systems for carrying data on a conductor… …   Wikipedia

  • Noise measurement — is carried out in various fields. In acoustics, it can be for the purpose of measuring environmental noise, or part of a test procedure using white noise, or some other specialised form of test signal. In electronics it relates to the sensitivity …   Wikipedia

Share the article and excerpts

Direct link
Do a right-click on the link above
and select “Copy Link”