Line code

Line code
An example of coding a binary signal using rectangular pulse amplitude modulation with polar non-return-to-zero code
An example of Bipolar encoding, or AMI.
Encoding of 11011000100 in Manchester encoding
An example of Biphase mark code
An example of MLT-3 encoding.

In telecommunication, a line code (also called digital baseband modulation, also called digital baseband transmission method) is a code chosen for use within a communications system for baseband transmission purposes. Line coding is often used for digital data transport.

Contents

Line coding

Line coding consists of representing the digital signal to be transported by an amplitude- and time-discrete signal that is optimally tuned for the specific properties of the physical channel (and of the receiving equipment). The waveform pattern of voltage or current used to represent the 1s and 0s of a digital data on a transmission link is called line encoding. The common types of line encoding are unipolar, polar, bipolar, and Manchester encoding.

For reliable clock recovery at the receiver, one usually imposes a maximum run length constraint on the generated channel sequence, i.e., the maximum number of consecutive ones or zeros is bounded to a reasonable number. A clock period is recovered by observing transitions in the received sequence, so that a maximum run length guarantees such clock recovery, while sequences without such a constraint could seriously hamper the detection quality.

After line coding, the signal is put through a "physical channel", either a "transmission medium" or "data storage medium". Sometimes the characteristics of two very different-seeming channels are similar enough that the same line code is used for them. The most common physical channels are:

  • the line-coded signal can directly be put on a transmission line, in the form of variations of the voltage or current (often using differential signaling).
  • the line-coded signal (the "baseband signal") undergoes further pulse shaping (to reduce its frequency bandwidth) and then modulated (to shift its frequency bandwidth) to create the "RF signal" that can be sent through free space.
  • the line-coded signal can be used to turn on and off a light source in Free Space Optics, most commonly infrared remote control.
  • the line-coded signal can be printed on paper to create a bar code.
  • the line-coded signal can be converted to magnetized spots on a hard drive or tape drive.
  • the line-coded signal can be converted to pits on an optical disc.

Unfortunately, most long-distance communication channels cannot transport a DC component. The DC component is also called the disparity, the bias, or the DC coefficient. The simplest possible line code, called unipolar because it has an unbounded DC component, gives too many errors on such systems.

Most line codes eliminate the DC component — such codes are called DC balanced, zero-DC, zero-bias or DC equalized etc. There are two ways of eliminating the DC component:

  • Use a constant-weight code. In other words, each transmitted code word is corrected such that every code word that contains some positive or negative levels also contains enough of the opposite levels, such that the average level over each code word is zero. For example, Manchester code and Interleaved 2 of 5.
  • Use a paired disparity code. In other words, the transmitter has to make sure that every code word that averages to a negative level is paired with another code word that averages to a positive level. Therefore it must keep track of the running DC buildup, and always pick the code word that pushes the DC level back towards zero. The receiver is designed so that either code word of the pair decodes to the same data bits. For example, AMI, 8B10B, 4B3T, etc.

Line coding should make it possible for the receiver to synchronize itself to the phase of the received signal. If the synchronization is not ideal, then the signal to be decoded will not have optimal differences (in amplitude) between the various digits or symbols used in the line code. This will increase the error probability in the received data.

It is also preferred for the line code to have a structure that will enable error detection.

Note that the line-coded signal and a signal produced at a terminal may differ, thus requiring translation.

A line code will typically reflect technical requirements of the transmission medium, such as optical fiber or shielded twisted pair. These requirements are unique for each medium, because each one has different behavior related to interference, distortion, capacitance and loss of amplitude.

Common line codes

Optical line codes:

  • Carrier-Suppressed Return-to-Zero
  • Alternate-Phase Return-to-Zero

See also

External links

References


Wikimedia Foundation. 2010.

Игры ⚽ Поможем написать курсовую

Look at other dictionaries:

  • line code — noun a code chosen for use within a communications system for transmission purposes …   Wiktionary

  • Line-code — Штрих код …   Краткий толковый словарь по полиграфии

  • Line rate — The line rate of a communications link is the data rate of its raw bitstream, including all framing bits and other physical layer overhead. Fact|date=June 2007 For example, the line rate of a T1 data link is 1.544 Mbit/s, of which 1.536 Mbit/s is …   Wikipedia

  • Line Mode Browser — displaying the German Wikipedia Original author(s) …   Wikipedia

  • Code coverage — is a measure used in software testing. It describes the degree to which the source code of a program has been tested. It is a form of testing that inspects the code directly and is therefore a form of white box testing.[1] Code coverage was among …   Wikipedia

  • Code Red (DVD Company) — Code Red Type DVD Distribution Company Industry Home video Products DVD Website …   Wikipedia

  • Code review — is systematic examination (often as peer review) of computer source code. It is intended to find and fix mistakes overlooked in the initial development phase, improving both the overall quality of software and the developers skills. Reviews are… …   Wikipedia

  • Code page 437 — Code page 437, as rendered by the IBM PC using a VGA adapter. IBM PC or MS DOS code page 437, often abbreviated CP437 and also known as DOS US, OEM US or sometimes misleadingly referred to as the OEM font, High ASCII or Extended ASCII,[1][2] is… …   Wikipedia

  • Code Lyôko — Code Lyoko Code Lyoko Titre original Code Lyoko Genre Série d animation, de science fiction Créateur(s) Jérome Mouscadet Production Nicolas Atlan Pays d’origine …   Wikipédia en Français

  • Code lyoko — Titre original Code Lyoko Genre Série d animation, de science fiction Créateur(s) Jérome Mouscadet Production Nicolas Atlan Pays d’origine …   Wikipédia en Français

Share the article and excerpts

Direct link
Do a right-click on the link above
and select “Copy Link”