- Frame (telecommunications)
computer networking, a frame is a data packetof fixed or variable length which has been encoded by a data link layercommunications protocol for digital transmission over a node-to-node link. Each frame consists of a "header" frame synchronizationand perhaps bit synchronization, payload (useful information, or a packet at higher protocol layer) and "trailer". Examples are Ethernetframes and Point-to-point protocol(PPP) frames.
telecommunications, the frame structure refers to the way a multiplexerdivides the underlying communication channel into several channels, so that it can be used simultaneously for transferring more than one data stream.
statistical multiplexing, a frame may be a container which could be filled by other frames, in a hierarchical structure of multiplexed channels. A frame may also be a data packetof fixed or variable length, including a header with a channel identification number or a destination address. One example of statistical multiplexing is the MPEGtransport stream used in digital TVtransmission, where the channel number is denoted Packet ID (PID). Another example is the TCP and UDP multiplexing, where the channel number is denoted port number. Other examples are the Frame Relayprotocol, where the channel number is called Data link connection identifier(DLCI),and Asynchronous Transfer Mode(ATM), where virtual circuits are identified hierarchically by a Virtual channel identifierand Virtual Path Identifier(VCI/VPI pair).
time-division multiplexing(TDM), a frame is a time interval of constant length, consisting of a fixed set of periodically repeated time slots of fixed length. Each time slot corresponds to one circuit switched (constant bitrate) channel. Not all time slots are necessarily in use. Normally a dedicated time slot is used for frame synchronization. The other timeslots only include payload data, typically one byte byte timeslot. No channel identification numbers are required, since the channel number is obvious from the position of the time slot relative to the frame synchronization.
The term in-frame is used to indicate that a time-division multiplexer is properly synchronized with the demultiplexer on the other end of the link, so that (barring in-flight data corruption) packets will be properly received.
One example of a TDM system is the
pulse-code modulation(PCM) system, in which each time slot consist of one byte of data, corresponding to a digitized sample of an analog signal, for example a phone call.
Wikimedia Foundation. 2010.
Look at other dictionaries:
Frame — A frame is a structural system that supports other components of a physical construction. Frame may also refer to:Engineering construction* Framing (construction), a building term known as light frame construction * Frame (vehicle), to which… … Wikipedia
Telecommunications engineering — Telecommunications engineering, or telecom engineering, is a major field within electronic engineering. The work ranges from basic circuit design to strategic mass developments. A telecommunication engineer is responsible for designing and… … Wikipedia
Telecommunications Services of Trinidad and Tobago — Limited (generally known as TSTT) is the largest telephone and Internet service provider in Trinidad and Tobago. The company, which is jointly owned by the Government of Trinidad and Tobago and Cable Wireless, was formed out of a merger of Telco… … Wikipedia
Frame relay — In the context of computer networking, frame relay consists of an efficient data transmission technique used to send digital information. It is a message forwarding relay race like system in which data packets, called frames, are passed from one… … Wikipedia
Telecommunications in Barbados — Communications in Barbados refers to the telephony, internet, postal, radio, and television systems of Barbados. Barbados has long been an informational and communications centre in the Caribbean region. Electricity coverage throughout Barbados… … Wikipedia
Frame Check Sequence — Pour les articles homonymes, voir FCS. Le Frame Check Sequence (FCS) est le code de détection d erreurs ajouté à la fin d une trame. C est le reste de la division modulo 2 de la trame par un polynôme de degré N (exemple HDLC, polynôme de degré 16 … Wikipédia en Français
Frame Control Header — Le Frame Control Header (FCH) est un en tête de trame utilisé dans le cadre du WiMAX. Il contient les informations nécessaires au décodage des cartes du lien descendant et du lien montant (la DL MAP et l UL MAP, qui précisent quand et sur quelles … Wikipédia en Français
telecommunications network — Introduction electronic system of links and switches, and the controls that govern their operation, that allows for data transfer and exchange among multiple users. When several users of telecommunications media wish to communicate with… … Universalium
Telecommunications in Sudan — Teleommunications in Sudan Contents 1 Pre privatization era (up to 1994) 2 Privatization era (1994 and Beyond) 3 Evolution of the telecommunication sector (1994 Sep 2006) … Wikipedia
Telecommunications facility — In telecommunication, the term facility has the following meanings: 1. A fixed, mobile, or transportable structure, including (a) all installed electrical and electronic wiring, cabling, and equipment and (b) all supporting structures, such as… … Wikipedia