Digital subscriber line

Digital subscriber line
DSL technologies
Standard
ADSL ANSI T1.413 Issue 2
ITU G.992.1 (G.DMT)
ITU G.992.2 (G.Lite)
ADSL2 ITU G.992.3
ITU G.992.4
ITU G.992.3 Annex J
ITU G.992.3 Annex L
ADSL2+ ITU G.992.5
ITU G.992.5 Annex M
HDSL ITU G.991.1
HDSL2  
IDSL  
MSDSL  
PDSL  
RADSL  
SDSL  
SHDSL ITU G.991.2
UDSL  
VDSL ITU G.993.1
VDSL2 ITU G.993.2

Digital subscriber line (DSL) is a family of technologies that provides digital data transmission over the wires of a local telephone network. DSL originally stood for digital subscriber loop. In telecommunications marketing, the term DSL is widely understood to mean Asymmetric Digital Subscriber Line (ADSL), the most commonly installed DSL technology. DSL service is delivered simultaneously with wired telephone service on the same telephone line. This is possible because DSL uses higher frequency bands for data separated by filtering. On the customer premises, a DSL filter on each outlet removes the high frequency interference, to enable simultaneous use of the telephone and data.

The data bit rate of consumer DSL services typically ranges from 256 kbit/s to 40 Mbit/s in the direction to the customer (downstream), depending on DSL technology, line conditions, and service-level implementation. In ADSL, the data throughput in the upstream direction, (the direction to the service provider) is lower, hence the designation of asymmetric service. In Symmetric Digital Subscriber Line (SDSL) services, the downstream and upstream data rates are equal.

Contents

History

Theory behind DSL, like many other forms of communication, can be traced back to Claude Shannon's seminal 1948 paper: A Mathematical Theory of Communication. An early patent was filed in 1987 for the use of wires for both voice phones and as a local area network.[1]

The motivation of digital subscriber line technology was the Integrated Services Digital Network (ISDN) specification proposed in 1984 by the CCITT (now ITU-T) as part of Recommendation I.120, later reused as ISDN Digital Subscriber Line (IDSL). Employees at Bellcore (now Telcordia Technologies) developed Asymmetric Digital Subscriber Line (ADSL) and filed a patent in 1988[2] by placing wide-band digital signals above the existing baseband analog voice signal carried between telephone company telephone exchanges and customers on conventional twisted pair cabling facilities.[3] Consumer-oriented ADSL was designed to operate on existing lines already conditioned for BRI ISDN services, which itself is a switched digital service (non-IP), though most incumbent local exchange carriers (ILECs) provision Rate-Adaptive Digital Subscriber Line (RADSL) to work on virtually any available copper pair facility—whether conditioned for BRI or not. Engineers developed higher-speed DSL facilities such as High bit rate Digital Subscriber Line (HDSL) and Symmetric Digital Subscriber Line (SDSL) to provision traditional Digital Signal 1 (DS1) services over standard copper pair facilities.

A DSL circuit provides digital service. The underlying technology of transport across DSL facilities uses high-frequency sinusoidal carrier wave modulation, which is an analog signal transmission. A DSL circuit terminates at each end in a modem which modulates patterns of bits into certain high-frequency impulses for transmission to the opposing modem. Signals received from the far-end modem are demodulated to yield a corresponding bit pattern that the modem retransmits, in digital form, to its interfaced equipment, such as a computer, router, switch, etc. Unlike traditional dial-up modems, which modulate bits into signals in the 300–3400 Hz baseband (voice service), DSL modems modulate frequencies from 4000 Hz to as high as 4 MHz. This frequency band separation enables DSL service and plain old telephone service (POTS) to coexist on the same copper pair facility. Generally, higher bit rate transmissions require a wider frequency band, though the ratio of bit rate to bandwidth are not linear due to significant innovations in digital signal processing and digital modulation methods.

A DSL Modem

Early DSL service required a dedicated dry loop, but when the U.S. Federal Communications Commission (FCC) required ILECs to lease their lines to competing DSL service providers, shared-line DSL became available. Also known as DSL over Unbundled Network Element, this unbundling of services allows a single subscriber to receive two separate services from two separate providers on one cable pair. The DSL service provider's equipment is co-located in the same central office as that of the ILEC supplying the customer's pre-existing voice service. The subscriber's circuit is then rewired to interface with hardware supplied by the ILEC which combines a DSL frequency and POTS frequency on a single copper pair facility.

On the subscriber's end of the circuit, inline low-pass DSL filters (splitters) are installed on each telephone to filter the high-frequency "hiss" that would otherwise be heard, but pass voice (5 kHz and below) frequencies. Conversely, high-pass filters already incorporated in the circuitry of DSL modems filter out voice frequencies. Although ADSL and RADSL modulations do not use the voice-frequency band, nonlinear elements in the phone could otherwise generate audible intermodulation and may impair the operation of the data modem in the absence of low-pass filters.

Older ADSL standards delivered 8 Mbit/s to the customer over about 2 km (1.2 mi) of unshielded twisted-pair copper wire. Newer variants improved these rates. Distances greater than 2 km (1.2 mi) significantly reduce the bandwidth usable on the wires, thus reducing the data rate. ADSL loop extenders increase these distances substantially.

Operation

Basic technology

Telephones are connected to the telephone exchange via a local loop, which is a physical pair of wires. Prior to the digital age, the use of the local loop for anything other than the transmission of speech, encompassing an audio frequency range of 300 to 3400 Hertz (voiceband or commercial bandwidth) was not considered. However, as long distance trunks were gradually converted from analog to digital operation, the idea of being able to pass data through the local loop (by utilizing frequencies above the voiceband) took hold, ultimately leading to DSL.

For a long time it was thought that it was not possible to operate a conventional phone-line beyond low-speed limits (typically under 9600 bit/s). In the 1950s, ordinary twisted-pair telephone-cable often carried four megahertz (MHz) television signals between studios, suggesting that such lines would allow transmitting many megabits per second. One such circuit in the UK ran some ten miles (16 km) between Pontop Pike transmitter and Newcastle on Tyne BBC Studios. It was able to give the studios a low quality cue feed but not one suitable for transmission.[citation needed] However, these cables had other impairments besides Gaussian noise, preventing such rates from becoming practical in the field. The 1980s saw the development of techniques for broadband communications that allowed the limit to be greatly extended.

The local loop connecting the telephone exchange to most subscribers has the capability of carrying frequencies well beyond the 3.4 kHz upper limit of POTS. Depending on the length and quality of the loop, the upper limit can be tens of megahertz. DSL takes advantage of this unused bandwidth of the local loop by creating 4312.5 Hz wide channels starting between 10 and 100 kHz, depending on how the system is configured. Allocation of channels continues at higher and higher frequencies (up to 1.1 MHz for ADSL) until new channels are deemed unusable. Each channel is evaluated for usability in much the same way an analog modem would on a POTS connection. More usable channels equates to more available bandwidth, which is why distance and line quality are a factor (the higher frequencies used by DSL travel only short distances). The pool of usable channels is then split into two different frequency bands for upstream and downstream traffic, based on a preconfigured ratio. This segregation reduces interference. Once the channel groups have been established, the individual channels are bonded into a pair of virtual circuits, one in each direction. Like analog modems, DSL transceivers constantly monitor the quality of each channel and will add or remove them from service depending on whether they are usable.

One of Lechleider's[4] contributions to DSL was his insight that an asymmetric arrangement offered more than double the bandwidth capacity of symmetric DSL. This allowed Internet Service Providers to offer efficient service to consumers, who benefited greatly from the ability to download large amounts of data but rarely needed to upload comparable amounts. ADSL supports two modes of transport: fast channel and interleaved channel. Fast channel is preferred for streaming multimedia, where an occasional dropped bit is acceptable, but lags are less so. Interleaved channel works better for file transfers, where the delivered data must be error free but latency incurred by the retransmission of errored packets is acceptable.

Because DSL operates above the 3.4 kHz voice limit, it cannot pass through a load coil. Load coils are, in essence, filters that block out any non-voice frequency. They are commonly set at regular intervals in lines placed only for POTS service. A DSL signal cannot pass through a properly installed and working load coil, while voice service cannot be maintained past a certain distance without such coils. Therefore, some areas that are within range for DSL service are disqualified from eligibility because of load coil placement. Because of this, phone companies endeavor to remove load coils on copper loops that can operate without them, and conditioning lines to avoid them through the use of fiber to the neighborhood or node (FTTN).

The commercial success of DSL and similar technologies largely reflects the advances made in electronics over the decades that have increased performance and reduced costs even while digging trenches in the ground for new cables (copper or fiber optic) remains expensive. Several factors contributed to the popularity of DSL technology:

  • Until the late 1990s, the cost of digital signal processors for DSL was prohibitive. All types of DSL employ highly complex digital signal processing algorithms to overcome the inherent limitations of the existing twisted pair wires. Due to the advancements of Very-large-scale integration (VLSI) technology, the cost of the equipment associated with a DSL deployment lowered significantly. The two main pieces of equipment are a Digital subscriber line access multiplexer (DSLAM) at one end and a DSL modem at the other end.
  • A DSL connection can be deployed over existing cable. Such deployment, even including equipment, is much cheaper than installing a new, high-bandwidth fiber-optic cable over the same route and distance. This is true both for ADSL and SDSL variations.
  • In the case of ADSL, competition in Internet access caused subscription fees to drop significantly over the years, thus making ADSL more economical than dial up access. Telephone companies were pressured into moving to ADSL largely due to competition from cable companies, which use DOCSIS cable modem technology to achieve similar speeds. Demand for high bandwidth applications, such as video and file sharing, also contributed to popularize ADSL technology.

Most residential and small-office DSL implementations reserve low frequencies for POTS service, so that (with suitable filters and/or splitters) the existing voice service continues to operate independent of the DSL service. Thus POTS-based communications, including fax machines and analog modems, can share the wires with DSL. Only one DSL "modem" can use the subscriber line at a time. The standard way to let multiple computers share a DSL connection uses a router that establishes a connection between the DSL modem and a local Ethernet, Powerline, or Wi-Fi network on the customer's premises.

Once upstream and downstream channels are established, a subscriber can connect to a service such as an Internet service provider.

Naked DSL

A naked DSL (a.k.a. standalone or dry loop DSL) is a way of providing DSL services without a PSTN (analogue telephony) service. It is useful when the customer does not need the traditional telephony voice service because voice service is received either on top of the DSL services (usually Voice over IP) or through another network (mobile telephony).

It is also commonly called a "UNE" for Unbundled Network Element, in the USA. It has started making a comeback in the US in 2004 when Qwest started offering it, closely followed by Speakeasy. As a result of AT&T's merger with SBC,[5] and Verizon's merger with MCI,[6] those telephone companies have an obligation to offer naked DSL to consumers.

Even without the regulatory mandate, however, many ILECs offer naked DSL to consumers. The number of telephone landlines in the US dropped from 188 million in 2000 to 172 million in 2005, while the number of cellular subscribers has grown to 195 million (277 million as of 2010).[7] This lack of demand for landline voice service has resulted in the expansion of naked DSL availability.

Naked DSL products are also marketed in some other countries e.g. Australia, New Zealand and Canada.

Typical setup

On the customer side, the DSL Transceiver, or ATU-R, or more commonly known as a DSL modem, is hooked up to a phone line. The telephone company (telco) connects the other end of the line to a DSLAM, which concentrates a large number of individual DSL connections into a single box. The location of the DSLAM depends on the telco, but it cannot be located too far from the user because of attenuation, the loss of data due to the large amount of electrical resistance encountered as the data moves between the DSLAM and the user's DSL modem. It is common for a few residential blocks to be connected to one DSLAM.

When the DSL modem powers up it goes through a sync procedure. The actual process varies from modem to modem but generally involves the following steps:

  1. The DSL transceiver performs a self-test.
  2. The DSL transceiver checks the connection between the DSL transceiver and the computer. For residential variations of DSL, this is usually the Ethernet (RJ-45) port or a USB port; in rare models, a FireWire port is used. Older DSL modems sported a native ATM interface (usually, a 25 Mbit/s serial interface). Also, some variations of DSL (such as SDSL) use synchronous serial connections.
  3. The DSL transceiver then attempts to synchronize with the DSLAM. Data can only come into the computer when the DSLAM and the modem are synchronized. The synchronization process is relatively quick (in the range of seconds) but is very complex, involving extensive tests that allow both sides of the connection to optimize the performance according to the characteristics of the line in use. External, or stand-alone modem units have an indicator labeled "CD", "DSL", or "LINK", which can be used to tell if the modem is synchronized. During synchronization the light flashes; when synchronized, the light stays lit, usually with a green color.

Modern DSL gateways have more functionality and usually go through an initialization procedure very similar to a PC boot up. The system image is loaded from the flash memory; the system boots, synchronizes the DSL connection and establishes the IP connection between the local network and the service provider, using protocols such as DHCP or PPPoE. The system image can usually be updated to correct bugs, or to add new functionality.

The accompanying figure is a schematic of a simple DSL connection (in blue). The right side the shows a DSLAM residing in the telephone company's central office. The left side shows the customer premises equipment with an optional router. This router manages a local area network (LAN) off of which are connected some number of PCs. With many service providers, the customer may opt for a modem which contains a wireless router. This option (within the dashed bubble) often simplifies the connection.

DSL Connection schematic

Customer Equipment

The customer end of the connection consists of a terminal adaptor or "DSL modem". This converts data between the digital signals used by computers and the voltage signal of a suitable frequency range which is then applied to the phone line.

DSL Modem schematic

In some DSL variations (for example, HDSL), the terminal adapter connects directly to the computer via a serial interface, using protocols such as ethernet or V.35. In other cases (particularly ADSL), it is common for the customer equipment to be integrated with higher level functionality, such as routing, firewalling, or other application-specific hardware and software. In this case, the equipment is referred to as a gateway.

Most DSL technologies require installation of appropriate filters to separate, or "split", the DSL signal from the low frequency voice signal. The separation can take place either at the demarcation point, or with filters installed at the telephone outlets inside the customer premises. Either way has its practical and economical limitations.

Example of a DSLAM from 2006

Exchange equipment

At the exchange, a digital subscriber line access multiplexer (DSLAM) terminates the DSL circuits and aggregates them, where they are handed off onto other networking transports. In the case of ADSL, the voice component is also separated at this step, either by a filter integrated in the DSLAM or by a specialized filtering equipment installed before it. The DSLAM terminates all connections and recovers the original digital information.

Protocols and configurations

Many DSL technologies implement an Asynchronous Transfer Mode (ATM) layer over the low-level bitstream layer to enable the adaptation of a number of different technologies over the same link.

DSL implementations may create bridged or routed networks. In a bridged configuration, the group of subscriber computers effectively connect into a single subnet. The earliest implementations used DHCP to provide network details such as the IP address to the subscriber equipment, with authentication via MAC address or an assigned host name. Later implementations often use Point-to-Point Protocol (PPP) or Asynchronous Transfer Mode (ATM) (Point-to-Point Protocol over Ethernet (PPPoE) or Point-to-Point Protocol over ATM (PPPoA)), while authenticating with a userid and password and using Point-to-Point Protocol (PPP) mechanisms to provide network details.

DSL technologies

The line-length limitations from telephone exchange to subscriber impose more restrictions on higher data-transmission rates. Technologies such as VDSL provide very high speed, short-range links as a method of delivering "triple play" services (typically implemented in fiber to the curb network architectures). Technologies likes GDSL can further increase the data rate of DSL. Fiber Optic technologies exist today that allow the conversion of copper based ISDN, ADSL and DSL over fiber optics.

DSL technologies (sometimes summarized as xDSL) include:

  • ISDN Digital Subscriber Line (IDSL), uses ISDN based technology to provide data flow that is slightly higher than dual channel ISDN.
  • High Data Rate Digital Subscriber Line (HDSL / HDSL2), was the first DSL technology that used a higher frequency spectrum of copper, twisted pair cables.
  • Symmetric Digital Subscriber Line (SDSL / SHDSL), the volume of data flow is equal in both directions.
  • Symmetric High-speed Digital Subscriber Line (G.SHDSL), a standardized replacement for early proprietary SDSL.
  • Asymmetric Digital Subscriber Line (ADSL), the volume of data flow is greater in one direction than the other.
  • Asymmetric Digital Subscriber Line 2 (ADSL2), an improved version of ADSL
  • Asymmetric Digital Subscriber Line 2 Plus (ADSL2+), A version of ADSL2 that doubles the data rates by using twice the spectrum.
  • Asymmetric Digital Subscriber Line Plus Plus (ADSL++), technology developed by Centillium Communications (Centillium has been acquired by TranSwitch Corp.) for the Japanese market that extends downstream rates to 50 Mbit/s by using spectrum up to 3.75 MHz.
  • Bonded DSL Rings (DSL Rings), A shared ring topology at 400 Mbit/s
  • Rate-Adaptive Digital Subscriber Line (RADSL), designed to increase range and noise tolerance by sacrificing up stream speed
  • Very High Speed Digital Subscriber Line (VDSL)
  • Very High Speed Digital Subscriber Line 2 (VDSL2), an improved version of VDSL
  • Etherloop Ethernet Local Loop
  • (Extended-) Reach Digital Subscriber Line
  • Uni-DSL (Uni Digital Subscriber Line or UDSL), technology developed by Texas Instruments, backwards compatible with all DMT standards
  • Gigabit Digital Subscriber Line (GDSL), based on binder MIMO technologies.[8]
  • Universal High bit rate Digital Subscriber Line (UHDSL) using fiber optics. Developed in 2005 by RLH Industries, Inc. Converts HDSL-1, 2 or 4 copper service into fiber optic HDSL service.
  • Internet Protocol Subscriber Line (IPSL), developed by Rim Semiconductor in 2007, allowed for 40 Mbit/s using 26 AWG copper telephone wire at a 5,500 ft (1,700 m) radius, 26 Mbit/s at a 6,000 ft (1,800 m) radius. The company operated until 2008.[9][10]

Transmission methods

Transmission methods vary by market, region, carrier, and equipment.

See also

References

  1. ^ Andrew R. Reichert, William J. Schirmer, Nicholas M. Esser, Bradley R. Nelson, Lauren T. May, Stewart C. Brown. "System for communicating digital data on a standard office telephone system". US Patent 4,785,448. http://www.google.com/patents?id=ZEQxAAAAEBAJ.  Filed February 23, 1987. Issued November 15, 1988.
  2. ^ Richard D. Gitlin, Sailesh K. Rao, Jean-Jacques Werner, Nicholas Zervos. "Method and apparatus for wideband transmission of digital signals between, for example, a telephone central office and customer premises". US Patent 4,924,492. http://www.google.com/patents/about?id=d2QjAAAAEBAJ.  Filed March 22, 1988. Issued May 8, 1990 }}
  3. ^ Ronald Shamus. ece.wpi.edu "EE535 Homework 3". Worcester Polytechnic Institute. Archived from the original on August 12, 2002. http://web.archive.org/web/20020812162700/http://www.ece.wpi.edu/courses/ee535/hwk96/hwk3cd96/rshamus/rshamus.html ece.wpi.edu. Retrieved September 15, 2011. 
  4. ^ Joseph W. Lechleider (August 1991). "High Bit Rate Digital Subscriber Lines: A Review of HDSL Progress" (fee required). IEEE Journal on Selected Areas in Communications 9 (6): 769–784. doi:10.1109/49.93088. http://ieeexplore.ieee.org/iel1/49/3051/00093088.pdf?tp=&isnumber=3051&arnumber=93088. 
  5. ^ SBC ATT Merger
  6. ^ Verizon MCI merger
  7. ^ Earthweb
  8. ^ B. Lee, J. Cioffi, et al. (September 2007). "Gigabit DSL". IEEE Transactions on Communication. 55 (9): 1689–1692. doi:10.1109/TCOMM.2007.904374. 
  9. ^ "IPSL Special Interest Group". consortium web site. 2007. Archived from the original on September 28, 2008. http://web.archive.org/web/20080928204631/http://www.ipslsig.org. Retrieved September 15, 2011. 
  10. ^ "Rim Semiconductor Company". official web site. Archived from the original on August 24, 2008. http://web.archive.org/web/20080824002511/http://www.rimsemi.com/. Retrieved September 15, 2011. 

Further reading

External links


Wikimedia Foundation. 2010.

Игры ⚽ Нужно решить контрольную?

Look at other dictionaries:

  • Digital Subscriber Line — (engl. für Digitaler Teilnehmeranschluss), kurz DSL, bezeichnet eine Reihe von Übertragungsstandards der Bitübertragungsschicht, bei der Daten mit hohen Übertragungsraten (bis zu 500 Mbit/s)[1] über einfache Kupferleitungen wie die… …   Deutsch Wikipedia

  • Digital subscriber line — Digital Subscriber Line, DSL ou encore xDSL (que l on peut traduire par « ligne numérique d abonné ») renvoie à l ensemble des technologies mises en place pour un transport numérique de l information sur une ligne de raccordement… …   Wikipédia en Français

  • Digital Subscriber Line — Digital Subscriber Line, DSL ou encore xDSL (que l on peut traduire par « ligne numérique d abonné ») renvoie à l ensemble des techniques mises en place pour un transport numérique de l information sur une ligne de raccordement… …   Wikipédia en Français

  • Digital subscriber line — хDSL  семейство технологий, позволяющих значительно расширить пропускную способность абонентской линии местной телефонной сети путём использования эффективных линейных кодов и адаптивных методов коррекции искажений линии на основе… …   Википедия

  • Digital Subscriber Line — Digital Subscriber Line,   DSL …   Universal-Lexikon

  • Digital Subscriber Line —    Abbreviated DSL. A high speed data transmission technology originally developed by Bellcore that delivers high bandwidth over existing twisted pair copper telephone lines.    There are several DSL services, providing data rates from 16Kbps to… …   Dictionary of networking

  • digital subscriber line — UK / US noun [countable] Word forms digital subscriber line : singular digital subscriber line plural digital subscriber lines computing a dsl …   English dictionary

  • Digital Subscriber Line — DSL sigla de Digital Subscriber Line (Línea de abonado digital) es un término utilizado para referirse de forma global a todas las tecnologías que proveen una conexión digital sobre línea de abonado de la red telefónica local: ADSL, ADSL2, ADSL2+ …   Enciclopedia Universal

  • digital subscriber line — noun A family of technologies that provides digital data transmission over the wires of a local telephone network. Often, this notion is used for the Asymmetric Digital Subscriber Line (ADSL), the most commonly installed technical variety of DSL …   Wiktionary

  • Digital\ Subscriber\ Line — Bezeichnung der Techniken für die Verbindung mit hoher Bandbreite über das Telefonnetz (ADSL und VDSL). Digital Subscriber Line (DSL) erlaubt, mehr Daten als gewöhnlich über herkömmliche Telefonleitungen (auch über Kupferkabel) zu schicken. Dabei …   Online-Wörterbuch Deutsch-Lexikon

Share the article and excerpts

Direct link
Do a right-click on the link above
and select “Copy Link”