CFM International CFM56

CFM International CFM56
CFM56
An exposed jet engine at a trade show. The rear of the polished metal fan case is visible on the left. The outer casing of the compressor section, covered in fuel lines and electrical wires is in to the right of the fan case. The right of the image shows the back of the engine, the exhaust area of the turbine section.
Rear view of CFM56-5
Type Turbofan
National origin France and United States
Manufacturer CFM International
First run June 1974
Major applications Airbus A320 family
Airbus A340
Boeing 737
KC-135R Stratotanker
Number built 20,270 (as of Jan 2010)
Developed from General Electric F101
Developed into CFM International LEAP-X

The CFM International CFM56 (U.S. military designation F108) series is a family of high-bypass turbofan aircraft engines made by CFM International (CFMI), with a thrust range of 18,000 to 34,000 pounds-force (80 to 150 kilonewtons). CFMI is a 50–50 joint-owned company of SNECMA, France and GE Aviation (GE), USA. Both companies are responsible for producing components and each has its own final assembly line. GE produces the high-pressure compressor, combustor, and high-pressure turbine, and SNECMA manufactures the fan, low-pressure turbine, gearbox, and exhaust. The engines are assembled by GE in Evendale, Ohio, and by SNECMA in Villaroche, France. The completed engines are marketed by CFMI.

The CFM56 first ran in 1974[1] and, despite initial political problems, is now one of the most common turbofan aircraft engines in the world, with more than 20,000 having been built[2] in four major variants. It is most widely used on the Boeing 737 airliner and, under military designation F108, replaced the Pratt & Whitney JT3D engines on many KC-135 Stratotankers in the 1980s, creating the KC-135R variant of this aircraft. It is also the only engine (CFM56-5C) used to power the Airbus A340-200 and 300 series. The engine is also fitted to Airbus A320 series aircraft.

Several fan blade failure incidents were experienced during the CFM56's early service, including one failure that was noted as a cause of the Kegworth air disaster, while some variants of the engine experienced problems caused by flight through rain and hail. However, both these issues were resolved with engine modifications. By January 2010, the CFM56 had flown more than 470 million cumulative hours (the equivalent of more than 53,000 years).[3]

History

Research into the next generation of commercial jet engines, high-bypass ratio turbofans in the "10-ton" (20,000 lbf; 89 kN) class, began in the late 1960s. SNECMA, who had mostly built military engines until then, was the first company to seek entrance into the market by searching for a partner with commercial experience to design and build an engine in this class. They considered Pratt & Whitney, Rolls-Royce, and GE Aviation as potential partners, but it was not until after two company executives, Gerhard Neumann from GE and René Ravaud from SNECMA, introduced themselves at the 1971 Paris Air Show that a decision was made. The two companies saw mutual benefit in the collaboration and met several more times, fleshing out the basics of the joint project.[4]

Pratt & Whitney dominated the commercial market at this point in time. GE needed an engine in this market class, and SNECMA had previous experience of working with them, collaborating on the production of the CF6-50 turbofan for the Airbus A300.[1] Pratt & Whitney was considering upgrading their JT8D to compete in the same class as the CFM56 as a sole venture, while Rolls-Royce dealt with financial issues that precluded them from starting new projects; this situation caused GE to gain the title of best partner for the program.[4]

A major reason for GE's interest in the collaboration, rather than building a 10-ton engine on their own, was that the SNECMA project was the only source of development funds for an engine in this class at this particular time. GE was initially considering only contributing technology from its CF6 engine rather than its much more advanced F101 engine, developed for the B-1 Lancer supersonic bomber. However, the company was faced with a dilemma when the United States Air Force (USAF) announced its Advanced Medium STOL Transport (AMST) project in 1972 which included funding for the development of a 10-ton engine – either to build a "limited" technology 10-ton engine with SNECMA, or a similar engine with "advanced" technology on their own. Concerned that the company would be left with only the "limited" engine in its portfolio if it did not win the Air Force contract (for which it was competing with Pratt & Whitney and a General Motors division with its "advanced" engine), GE decided to apply for an export license for the F101 core technology.[5]

Export issues

GE applied for the export license in 1972 as their primary contribution to the 10-ton engine project. However, the United States Department of State's Office of Munitions Control recommended the rejection of the application on national security grounds; specifically because the core technology was an aspect of a strategic national defense system (the B-1 bomber), it was built with Department of Defense (and therefore American taxpayer) money, and that exporting the technology to France would limit the number of American workers on the project.[6] The official decision was made in a National Security Decision Memorandum signed by the National Security Advisor Henry Kissinger on 19 September 1972.[7]

While national security concerns were cited as the grounds for rejection, reportedly high-level politics played an important role as well. The project, and the export issue associated with it, was considered so important that French President Georges Pompidou appealed directly to U.S. President Richard Nixon in 1971 to approve the deal, and that Henry Kissinger brought the issue up with President Pompidou in a 1972 meeting. GE reportedly argued at the highest levels that having half of the market was better than having none of it, which they believed would happen if SNECMA pursued the engine on their own without GE's contribution. However, Nixon administration officials feared that this project could be the beginning of the end of American aerospace leadership.[8]

There was also speculation that the rejection may have been, in part, retaliation for French involvement in convincing the Swiss not to purchase American-made A-7 Corsair II aircraft that had been competing against a French design,[8] the Dassault Milan. In the end, the Swiss did not purchase either aircraft, opting for the Northrop F-5E Tiger II instead.[9]

1973 Nixon–Pompidou meeting

Two men in suits stand to the right, with uniformed military officers nearby. Both men are waving and smiling.
U.S. President Nixon (left) and French President Georges Pompidou (right) prior to the 1973 U.S.–French summit in Reykjavík, Iceland

Despite the export license being rejected, both the French and GE continued to push the Nixon Administration for permission to export the F101 technology. Efforts continued throughout the months following the rejection, culminating in the engine becoming an agenda topic during the 1973 meeting of Presidents Nixon and Pompidou in Reykjavík. Discussions at this meeting resulted in an agreement that allowed the development of the CFM56 to proceed. Contemporary reports state that the agreement was based on assurances that the core of the engine, the part that GE was developing from the military F101, would be built in the U.S. and then transported to France in order to protect the sensitive technologies.[10] The joint venture also agreed to pay the U.S. an $80 million royalty fee (calculated at $20,000 per engine predicted to be built) as repayment for the development money provided by the government for the F101 engine core.[4] Documents declassified in 2007 revealed that a key aspect of the CFM56 export agreement was that the French government agreed not to seek tariffs against American aircraft being imported into Europe.[11]

CFM International

With the export issue settled, GE and SNECMA finalized the agreement that formed CFM International (CFMI), a 50–50 joint company that would be responsible for producing and marketing the 10-ton engine, the CFM56. The venture was officially founded in 1974.[12] The two primary roles for CFMI were to manage the program between GE and SNECMA, and to market, sell and service the engine at a single point of contact for the customer. CFMI was made responsible for the day-to-day decision making for the project, while major decisions (developing a new variant, for example) required the go-ahead from GE and SNECMA management.[1]

The CFMI board of directors is currently split evenly between SNECMA and GE (five members each). There are two vice presidents, one from each company, who support the President of CFMI. The president tends to be drawn from SNECMA and sits at CFMI's headquarters near GE in Cincinnati, Ohio.[1]

The work split between the two companies gave GE responsibility for the high-pressure compressor (HPC), the combustor, and the high-pressure turbine (HPT); while SNECMA was responsible for the fan, the low-pressure compressor (LPC), and the low-pressure turbine (LPT).[13] SNECMA was also responsible for the initial airframe integration engineering, mostly involving the nacelle design, and was initially responsible for the gearbox, but shifted that work to GE when it became apparent that it would be more efficient for GE to assemble that component along with their other parts.[14]

Development

Development work on the CFM56 began before CFMI was formally created. While work proceeded smoothly, the international arrangement led to unique working conditions. For example, both companies had assembly lines, some engines were assembled and tested in the U.S. and others in France. Engines assembled in France were subject to the initially strict export agreement, which meant that GE's core was built in the U.S., then shipped to the SNECMA plant in France where it was placed in a locked room into which even the President of SNECMA was not allowed. The SNECMA components (the fore and aft sections of the engine) were brought into the room, GE employees mounted them to the core, and then the assembled engine was taken out to be finished.[15]

The first completed CFM56 engine first ran at GE in June 1974 with the second running in October 1974. The second engine was then shipped to France and first ran there on December 13, 1974. These first engines were considered "production hardware" as opposed to test examples and were designated as the CFM56-2, the first variant of the CFM56.[14]

The engine flew for the first time in February 1977 when it replaced one of the four Pratt & Whitney JT8D engines on the McDonnell Douglas YC-15, an entrant in the Air Force's Advanced Medium STOL Transport (AMST) competition.[16] Soon after, the second CFM56 was mounted on a Sud Aviation Caravelle at the SNECMA flight test center in France. This engine had a slightly different configuration with a long bypass duct and mixed exhaust flow,[nb 1] rather than a short bypass duct with unmixed exhaust flow.[nb 2] It was the first to include a "Thrust Management System" to maintain engine trim.[nb 3][17]

First customers

After testing the engine for several years, both in the air and on the ground, CFMI searched for customers outside of a possible AMST contract. The main targets were re-engine contracts for the Douglas DC-8 and the Boeing 707 airliners, including the related military tanker, the KC-135 Stratotanker. There was little initial interest in the engine, but Boeing realized that the CFM56 might be a solution to upcoming noise regulations.[4] After announcing that a 707 would be configured with the CFM56 engine for flight tests in 1977, Boeing officially offered the 707-320 with the CFM56 engine as an option in 1978. The new variant was listed as the 707-700.[18] However, due to limited interest from the airlines in a re-engined 707, Boeing ended the 707-700 program in 1980 without selling any aircraft.[19] Despite the lack of sales, having the commercial 707 available with the CFM56 helped the engine's competitiveness for the KC-135 re-engine contract.[20]

KC-135R

The front of several gray aircraft are centered in the image.
A nose-on view of several re-engined KC-135R aircraft taxiing prior to takeoff. The new engines are CFM56-2 high-bypass turbofans.

Winning the contract to re-engine the KC-135 tanker fleet for the USAF would be a huge boon to the CFM56 project (with more than 600 aircraft available to re-engine), and CFMI aggressively pursued that goal as soon as the Request For Proposals (RFP) was announced in 1977. Like other aspects of the program, international politics played their part in this contract. In efforts to boost the CFM56's chances versus its competitors, the Pratt & Whitney TF33 and an updated Pratt & Whitney JT8D, the French government announced in 1978 that they would upgrade their 11 KC-135s with the CFM56, providing one of the first orders for the engine.[21]

The USAF announced the CFM56 as the winner of the re-engine contract in January 1980. Officials indicated that they were excited at the prospect of replacing the Pratt & Whitney J57 engines currently flying on the KC-135A aircraft, calling them "...the noisiest, dirtiest, [and] most fuel inefficient powerplant still flying" at the time.[22] The re-engined aircraft was designated the KC-135R. The CFM56 brought many benefits to the KC-135, decreasing takeoff distance by as much as 3,500 ft (1,100 m), decreasing overall fuel usage by 25%, greatly reducing noise (24 dB lower) and lowering total life cycle cost. With those benefits in mind, the United States Navy selected the CFM56-2 to power their variant of the Boeing 707, the E-6 Mercury, in 1982.[20] Additionally, in 1984 the Royal Saudi Air Force selected the CFM56-2 to power their E-3 Sentry aircraft (also related to the 707 airframe). The CFM56-2-powered E-3 also became the standard configuration for aircraft purchased by the British and French.[1]

DC-8

By the end of the 1970s, airlines were considering upgrading their aging Douglas DC-8 aircraft as an alternative to buying new quieter and more efficient aircraft. Following the French KC-135 order in 1978, the April 1979 decision by United Airlines to upgrade 30 of their DC-8-61 aircraft with the CFM56-2 was important for securing the development of the CFM56;[23] GE and SNECMA were two weeks away from freezing development had that order not materialized.[4] This decision marked the first commercial purchase (rather than government/military) of the engine, and Delta Air Lines and Flying Tiger Line soon followed suit, giving the CFM56 a firm footing in both the military and commercial realms.[1]

Boeing 737

A zoomed-in view of the front of an engine nacelle. The fan blades of the engine are in the middle of the image. They are surrounded by the engine nacelle, which is seemingly circular on the top half, and flattened on the bottom half.
Engine inlet of a CFM56-3 engine on a Boeing 737-400 series showing the non-circular design

In the early 1980s Boeing selected the CFM56-3 to exclusively power the latest Boeing 737 variant, the 737-300. The 737 wings were closer to the ground than previous applications for the CFM56, necessitating several modifications to the engine. The fan diameter was reduced, which reduced the bypass ratio, and the engine accessory gearbox was moved from the bottom of the engine (the 6 o'clock position) to the 9 o'clock position, giving the engine nacelle its distinctive flat-bottomed shape. The overall thrust was also reduced, from 24,000 to 20,000 lbf (110 to 89 kN), mostly due to the reduction in bypass ratio.[24]

Since the small initial launch order for twenty 737-300s split between two airlines,[1] over 5,000 Boeing 737 aircraft had been delivered with CFM56 turbofans by April 2010, resounding proof of the engine's adaptability.[25]

Continued development

Once the CFM56 was well established in both military and commercial applications, CFMI continued to improve the engine and market it for new aircraft, such as the Airbus A320 and the Airbus A340. As of 2010, there are four major variants of the engine, each with multiple sub-variants.

Tech56 and Tech Insertion

In 1998, CFMI launched the "Tech56" development and demonstration program to create an engine for the new single-aisle aircraft that were expected to be built by Airbus and Boeing. The program focused on developing a large number of new technologies for the theoretical future engine, not necessarily creating an all-new design.[26][27] However, when it became clear that Boeing and Airbus were not going to build all-new aircraft to replace the 737 and A320, CFMI decided to apply some of those Tech56 technologies to the CFM56 in the form of the "Tech Insertion" program which focused on three areas: fuel efficiency, maintenance costs and emissions. Launched in 2004, the package included redesigned high-pressure compressor blades, an improved combustor, and improved high- and low-pressure turbine components[28][29] which resulted in better fuel efficiency and lower nitrogen oxides (NOx) emissions. The new components also reduced engine wear, lowering maintenance costs by about 5%. The engines entered service in 2007, and all new CFM56-5B and CFM56-7B engines are being built with the Tech Insertion components. CFMI also offers the components as an upgrade kit for existing engines.[28]

CFM56-7B "Evolution"

In 2009, CFMI announced the latest upgrade to the CFM56 engine, the "CFM56-7B Evolution" or CFM56-7BE. This upgrade, announced alongside Boeing's newest 737 variant, further enhances the high- and low-pressure turbines with better aerodynamics, as well as improving engine cooling, and aims to reduce overall part count.[30] CFMI expected the changes to result in a 4% reduction in maintenance costs and a 1% improvement in fuel consumption (2% improvement including the airframe changes for the new 737); however, flight and ground tests completed in May 2010 revealed that the fuel burn improvement was better than expected at 1.6%.[31] Following 450 hours of testing, the CFM56-7BE engine was certified by FAA and EASA on July 30, 2010.[32]

While the CFM56-7BE engine is designed specifically for Boeing's new 737, CFMI have proposed a similar Evolution upgrade for the CFM56-5B engines that power Airbus's A320. As of May 2010, Airbus has not made any commitment to a new engine.[31]

Design

The CFM56 is a high-bypass turbofan engine (the majority of the air accelerated by the fan bypasses the core of the engine and is exhausted out of the fan case) with several variants having bypass ratios ranging from 5:1 to 6:1, generating 18,500 to 34,000 lbf (80 kN to 150 kN) of thrust. The variants share a common design, but the details differ. The CFM56 is a two-shaft (or two-spool) engine, meaning that there are two rotating shafts, one high-pressure and one low-pressure. Each is powered by its own turbine section (the high-pressure and low-pressure turbines, respectively). The fan and booster (low pressure compressor) evolved over the different iterations of the engine, as did the compressor, combustor and turbine sections.[1]

Fan and booster

The front fan of a jet engine facing the left of the image, surrounded by its metal casing. The conical inlet in seen right in front of the metal fan blades. The fan casing is seen in three distinct (but attached) sections from left to right, first a silver-colored section, then a golden-colored section, then another silver-colored section.
View of the CFM56-5 front fan and fan case

The CFM56 features a single-stage fan, and most variants have a three-stage booster on the low-pressure shaft,[nb 4] with four stages in the -5B and -5C variants.[33] The booster is also commonly called the "low-pressure compressor" (LPC) as it sits on the low-pressure shaft and compresses the flow initially before reaching the high-pressure compressor. The original CFM56-2 variant featured 44 tip-shrouded fan blades,[34][nb 5] although the number of fan blades was reduced in later variants as wide-chord blade technology developed, down to 22 blades in the latest variant, the CFM56-7.[35]

The CFM56 fan features dovetailed fan blades which allows them to be replaced without removing the entire engine, and GE/SNECMA claim that the CFM56 was the first engine to have that capability. This attachment method is useful for circumstances where only a few fan blades need to be repaired or replaced, such as following bird strikes.[36]

The fan diameter varies with the different models of the CFM56, and that change has a direct impact on the engine performance. For example, the low-pressure shaft rotates at the same speed for both the CFM56-2 and the CFM56-3 models; however, the fan diameter is smaller on the -3, which lowers the tip speed of the fan blades. The lower speed allows the fan blades to operate more efficiently (5.5% more in this case), which increases the overall fuel efficiency of the engine (improving specific fuel consumption nearly 3%).[24]

Compressor

An engine is shown on a display stand at a museum, with the front of the engine facing left. Sections of the casing are cut away and replaced with clear plastic, revealing the booster blades, the compressor blades, and the turbine blades, from left to right.
View of an opened CFM56-3 engine, focused at the high-pressure compressor

The high-pressure compressor (HPC), which was at the center of the original export controversy, features nine stages in all variants of the CFM56. The compressor was developed from GE's "GE1/9" core (named for its single-turbine, nine-compressor stage design) which was designed to be a physically compact core. The small physical size of the compressor meant that the entire engine could be lighter and less complex, as the number of support systems (such as bearings and oil systems) could be reduced.[4] As the design developed, the HPC was improved, mostly through better blade design. As a part of the Tech 56 program, CFMI tested a new six-stage high-pressure compressor that was designed to have the same pressure ratio as the CFM56's nine-stage compressor. While that compressor was not integrated into the CFM56, CFMI offered an upgraded HPC, again improved with better blade aerodynamics, as a part of their "Tech Insertion" package in 2007.[27][37]

Combustor

Most variants of the CFM56 feature a single-annular combustor. An annular combustor is a continuous ring where fuel is injected into the airflow and ignited, raising the pressure and temperature of the flow. Other types of combustors include can combustors, where each combustion chamber is separate, and canannular which is a hybrid of the two.

In 1989, CFMI began work on a new, double-annular combustor. Instead of having just one combustion zone, the double-annular combustor has a second combustion zone that is used at high thrust levels. This design lowers the emissions of both nitrogen oxides (NOx) and carbon dioxide (CO2). The first CFM56 engine with the double-annular combustor entered service in 1995, and the combustor is used on "Tech Insertion" CFM56-5B and CFM56-7B variants.[38]

GE started developing and testing a new type of combustor called the Twin Annular Premixing Swirler combustor, or "TAPS", during the Tech 56 program.[27] This design is similar to the double-annular combustor in that it has two combustion zones; however, this combustor "swirls" the flow, creating an ideal fuel–air mixture. This difference allows the combustor to generate much less NOx than other combustors. Tests on a CFM56-7B engine demonstrated an improvement of 46% over single-annular combustors and 22% over double-annular combustors.[39] The analytical tools developed for TAPS have also been used to improve other combustors, notably the single-annular combustors in some CFM56-5B and -7B engines.[40]

Turbine

All variants of the CFM56 feature a single-stage high-pressure turbine (HPT). In some variants, the HPT blades are "grown" from a single crystal superalloy, giving them high strength and creep resistance. The low-pressure turbine (LPT) features four stages in most variants of the engine, but the CFM56-5C has a five-stage LPT. This change was implemented to drive the larger fan on this variant.[41] Improvements to the turbine section were examined during the Tech56 program, and one development was an aerodynamically optimized low-pressure turbine blade design, which would have used 20% fewer blades for the whole low-pressure turbine, saving weight. Some of those Tech56 improvements made their way into the Tech Insertion package, where the turbine section was updated.[27] The turbine section was updated again in the "Evolution" upgrade.[28][31]

The high-pressure turbine stages in the CFM56 are internally cooled by air from the high-pressure compressor. The air passes through internal channels in each blade and ejects at the leading and trailing edges.[36]

Exhaust

Although CFMI tested both a mixed and unmixed exhaust design at the beginning of development,[1] most variants of the engine feature an unmixed exhaust nozzle.[nb 2] Only the high-power CFM56-5C, designed for the Airbus A340, has a mixed-flow exhaust nozzle.[nb 1][41]

Additionally, GE and SNECMA tested the effectiveness of chevrons on reducing jet noise.[nb 6][42] After examining configurations in the wind tunnel, CFMI chose to flight-test chevrons built into the core exhaust nozzle. The chevrons reduced jet noise by 1.3 perceived loudness decibels during takeoff conditions, and are now offered as an option with the CFM56 for the Airbus A321.[43]

Reverse thrust

The middle of an airplane fuselage, white with "easyJet" painted in orange, is visible with the jet engine under the wing in the center of the image. Small doors on the rear half engine are open.
Pivoting door thrust reversers are visible on this Easyjet Airbus A319-100.

The CFM56 is designed to support several reverse thrust systems which help slow and stop the aircraft after landing. The variants built for the Boeing 737, the CFM56-3 and the CFM56-7, use a cascade type of thrust reverser. This type of thrust reverse consists of sleeves that slide back to expose mesh-like cascades and blocker doors that block the bypass air flow. The blocked bypass air is forced through the cascades, reducing the thrust of the engine and slowing the aircraft down.[44][45]

The CFM56 also supports pivoting-door type thrust reversers. This type is used on the CFM56-5 engines that power many Airbus aircraft. They work by actuating a door that pivots down into the bypass duct, both blocking the bypass air and deflecting the flow outward, creating the reverse thrust.[46]

Variants

CFM56-2 series

The CFM56-2 series is the original variant of the CFM56. It is most widely used in military applications where it is known as the F108; specifically in the KC-135, the E-6 Mercury and some E-3 Sentry aircraft. The CFM56-2 comprises a single-stage fan with 44 blades, with a three-stage LP compressor driven by a four-stage LP turbine, and a nine-stage HP compressor driven by a single-stage HP turbine. The combustor is annular.[34]

Model Thrust Bypass Ratio Pressure Ratio Dry Weight[nb 7] Applications
CFM56-2A-2 (-3) 24,000 lbf (110 kN) 5.9 31.8 4,820 lb (2,190 kg) E-3 Sentry, E-6 Mercury
CFM56-2B1 22,000 lbf (98 kN) 6.0 30.5 4,671 lb (2,120 kg) KC-135R Stratotanker, Boeing RC-135
CFM56-2C1 22,000 lbf (98 kN) 6.0 31.3 4,653 lb (2,110 kg) Douglas DC-8-70

CFM56-3 series

 A close-up view of a CFM56-3 series engine mounted on a Boeing 737-300 showing flattening of the nacelle at the bottom of the inlet lip.
A CFM56-3 series engine mounted on a Boeing 737-300 airliner showing flattening of the nacelle at the bottom of the inlet lip.

The first derivative of the CFM56 series, the CFM56-3 is designed for Boeing 737-300/-400/-500 series aircraft, with static thrust ratings from 18,500 to 23,500 lbf (82.3 to 105 kN). A "cropped fan" derivative of the -2, the -3 engine has a smaller fan diameter at 60 in (1.5 m) but retains the original basic engine layout. The new fan is primarily derived from GE's CF6-80 turbofan rather than the CFM56-2, and the booster was redesigned to match the new fan.[24]

A significant challenge for this series was achieving ground clearance for the wing-mounted engine. This was overcome by reducing the intake fan diameter and relocating the gearbox and other accessories from beneath the engine to the sides. The resulting flattened nacelle bottom and intake lip yielded the distinctive appearance of the Boeing 737 with CFM56 engines.[47]

Model Thrust Bypass Ratio Pressure Ratio Dry Weight Applications
CFM56-3B-1 20,000 lbf (89 kN) 6.0 27.5 4,276 lb (1,940 kg) Boeing 737-300, Boeing 737-500
CFM56-3B-2 22,000 lbf (98 kN) 5.9 28.8 4,301 lb (1,950 kg) Boeing 737-300, Boeing 737-400
CFM56-3C-1 23,500 lbf (100 kN) 6.0 30.6 4,301 lb (1,950 kg) Boeing 737-300, Boeing 737-400, Boeing 737-500

CFM56-4 series

The CFM56-4 series was a proposed improved version of the CFM56-2 designed for the Airbus A320 family of aircraft. Competing with the RJ500 engine being developed by Rolls-Royce, the -4 series was designed to produce 25,000 lbf (110 kN) and was to feature a new 68 in (1.73 m) fan, a new low-pressure compressor and a Full Authority Digital Engine Controller (FADEC). However, soon after the upgrade project was launched in 1984, International Aero Engines offered their new V2500 engine for the A320. CFMI realized that the CFM56-4 did not compare favorably with the new engine and scrapped the project to begin working on the CFM56-5 series.[4]

CFM56-5 series

CFM56-5 at Airbus A320-200

The CFM56-5 series is designed for the Airbus aircraft and has a very wide thrust rating of between 22,000 and 34,000 lbf (97.9 and 151 kN). It has three distinct sub-variants; the CFM56-5A, CFM56-5B and CFM56-5C,[4] and differs from its Boeing-fitted cousins by featuring a FADEC and incorporating further aerodynamic design improvements.

CFM56-5A series

The CFM56-5A series is the initial CFM56-5 series, designed to power the short-to-medium range Airbus A320 family. Derived from the CFM56-2 and CFM56-3 families, the -5A series produces thrusts between 22,000 and 26,500 lbf (98 kN and 118 kN). Aerodynamic improvements such as an updated fan, low-pressure compressor, high-pressure compressor and combustor make this variant 10–11% more fuel efficient than its predecessors.[48][49]

Model Thrust Bypass Ratio Pressure Ratio Dry Weight Applications
CFM56-5A1 25,000 lbf (111 kN) 6.0 31.3 4,995 lb (2,270 kg) Airbus A320
CFM56-5A3 26,500 lbf (118 kN) 6.0 31.3 4,995 lb (2,270 kg) Airbus A320
CFM56-5A4 22,000 lbf (97.9 kN) 6.2 31.3 4,995 lb (2,270 kg) Airbus A319
CFM56-5A5 23,500 lbf (105 kN) 6.2 31.3 4,995 lb (2,270 kg) Airbus A319
CFM56-5B series
CFM56-5B6 on an Airbus A319-112

An improvement of the CFM56-5A series, it was originally designed to power the A321. With a thrust range between 22,000 and 33,000 lbf (98 kN and 147 kN) it can power every model in the A320 family (A318/A319/A320/A321) and has superseded the CFM56-5A series. Among the changes from the CFM56-5A is the option of a double-annular combustor that reduces emissions (particularly NOx), a new fan in a longer fan case, and a new low-pressure compressor with a fourth stage (up from three in earlier variants). It is the most numerous engine supplied to Airbus.[33][50]

Model Thrust Bypass Ratio Pressure Ratio Dry Weight Applications
CFM56-5B1 30,000 lbf (130 kN) 5.5 35.4 5,250 lb (2,380 kg) Airbus A321
CFM56-5B2 31,000 lbf (140 kN) 5.5 35.4 5,250 lb (2,380 kg) Airbus A321
CFM56-5B3 33,000 lbf (150 kN) 5.4 35.5 5,250 lb (2,380 kg) Airbus A321
CFM56-5B4 27,000 lbf (120 kN) 5.7 32.6 5,250 lb (2,380 kg) Airbus A320
CFM56-5B5 22,000 lbf (98 kN) 6.0 32.6 5,250 lb (2,380 kg) Airbus A319
CFM56-5B6 23,500 lbf (100 kN) 5.9 32.6 5,250 lb (2,380 kg) Airbus A319
CFM56-5B7 27,000 lbf (120 kN) 5.7 35.5 5,250 lb (2,380 kg) Airbus A319, A319CJ
CFM56-5B8 21,600 lbf (96 kN) 6.0 32.6 5,250 lb (2,380 kg) Airbus A318
CFM56-5B9 23,300 lbf (100 kN) 5.9 32.6 5,250 lb (2,380 kg) Airbus A318
CFM56-5C series

With a thrust rating of between 31,200 and 34,000 lbf (139 kN and 151 kN), the CFM56-5C series is the most powerful of the CFM56 family. It powers Airbus' long-range A340-200 and -300 airliners, and entered service in 1993. The major changes are a larger fan, a fifth low-pressure turbine stage, and the same four-stage low-pressure compressor found in the -5B variant.[51]

Unlike every other variant of the CFM56, the -5C features a mixed-exhaust nozzle,[nb 1] which offers slightly higher efficiency.[41]

Model Thrust Bypass Ratio Pressure Ratio Dry Weight Applications
CFM56-5C2 31,200 lbf (139 kN) 6.6 37.4 8,796 lb (3,990 kg) Airbus A340-200/-300
CFM56-5C3 32,500 lbf (145 kN) 6.5 37.4 8,796 lb (3,990 kg) Airbus A340-200/-300
CFM56-5C4 34,000 lbf (151 kN) 6.4 38.3 8,796 lb (3,990 kg) Airbus A340-200/-300

CFM56-7 series

The CFM56-7 powers the Boeing 737 Next Generation series (737-600/-700/-800/-900). The CFM56-7 is rated with takeoff thrust from 19,500 to 27,300 lbf (86.7 kN to 121 kN). It has higher thrust ranges, improved efficiency, and lower maintenance costs than its predecessor, the CFM56-3 series. It incorporates features from the CFM56-5 series such as FADEC, double-annular combustor (as an option), and improved internal design. The basic mechanical arrangement is as the -3 series, but all aspects were aerodynamically improved from that model. For example, the improved wide-chord fan blades allowed the total number of fan blades to be reduced from 44 to 24. Other improvements came from material advances, such as the use of single-crystal turbine blades in the high-pressure turbine.[52]

The CFM56-7-powered 737 is granted 180-minute Extended-Range, Twin-Engine Operations (ETOPS) approval by the U.S. Federal Aviation Administration. It also powers the military versions of the Next-Generation 737, the C-40 Clipper, the P-8 Poseidon, and Boeing 737 AEW&C.[53]

Model Thrust Bypass Ratio Pressure Ratio Dry Weight Applications
CFM56-7B18 19,500 lbf (86.7 kN) 5.5 32.8 5,216 lb (2,370 kg) Boeing 737-600
CFM56-7B20 20,600 lbf (91.6 kN) 5.5 32.8 5,216 lb (2,370 kg) Boeing 737-600, Boeing 737-700
CFM56-7B22 22,700 lbf (101 kN) 5.3 32.8 5,216 lb (2,370 kg) Boeing 737-600, Boeing 737-700
CFM56-7B24 24,200 lbf (108 kN) 5.3 32.8 5,216 lb (2,370 kg) Boeing 737-700, Boeing 737-800, Boeing 737-900
CFM56-7B26 26,300 lbf (117 kN) 5.1 32.8 5,216 lb (2,370 kg) Boeing 737-700, Boeing 737-800, Boeing 737-900
CFM56-7B27 27,300 lbf (121 kN) 5.1 32.8 5,216 lb (2,370 kg) Boeing 737-800, Boeing 737-900, Boeing Business Jet

Engine failures

Although the CFM56 is a very reliable engine (CFMI state that there is only one in-flight shutdown every 333,333 hours),[54] there have been several engine failures throughout the life of the CFM56 family which were serious enough to either ground the fleet or require aspects of the engine to be redesigned.

Rain/hail ingestion

There are several recorded incidents of CFM56 engines flaming out in heavy rain and/or hail conditions, beginning early in the CFM56's career. In 1987, a double flameout occurred in hail conditions (the pilots managed to relight the engines), followed by the TACA Flight 110 incident in 1988. Both CFM56 engines on the TACA 737 flamed out while passing through hail and heavy rain, and the crew was forced to land without engines on a grassy levee near New Orleans, Louisiana. CFMI modified the engines by adding a sensor to force the combustor to continuously ignite under those conditions.[4]

In 2002, Garuda Indonesia Flight 421 had to ditch into a river because of hail-induced engine flameouts, killing a flight attendant and injuring dozens of passengers. Prior to this accident, there were several other incidents of single or dual flameouts due to these weather conditions. After three incidents through 1998, CFMI made modifications to the engine to improve the way in which the engine handled hail ingestion. The major changes included a modification to the fan/booster splitter (making it more difficult for hail to be ingested by the core of the engine) and the use of an elliptical, rather than conical, spinner at the intake. While these changes did not prevent the 2002 accident, the investigation board found that the pilots did not follow the proper procedures for attempting to restart the engine, which contributed to the final result. Recommendations were made to better educate pilots on how to handle these conditions, as well as to revisit FAA rain and hail testing procedures. No further engine modifications were recommended.[55]

Fan blade failure

One issue that led to accidents with the CFM56-3C engine was the failure of fan blades. This mode of failure led to the Kegworth air disaster in 1989, which killed 47 people and injured 74 more. After the fan blade failed, the pilots mistakenly shut down the wrong engine, resulting in the damaged engine failing completely when powered up after descent. Following the Kegworth accident, CFM56 engines fitted to a Dan-Air 737-400 and a British Midland 737-400 suffered fan blade failures under similar conditions, although neither incident resulted in a crash or injuries.[56] After the second incident, the 737-400 fleet was grounded.

At the time it was not mandatory to flight test new variants of existing engines, and certification testing failed to reveal vibration modes that the fan experienced during the regularly performed power climbs at high altitude. Analysis revealed that the fan was being subjected to worse than expected high-cycle fatigue stresses, causing the blade to fracture; and more severe than tested for certification. Less than a month after grounding, the fleet was allowed to resume operations once the fan blades and fan disc were replaced and the electronic engine controls were modified to reduce maximum engine thrust to 22,000 lbf (98 kN) from 23,500 lbf (105 kN).[57] The redesigned fan blades were installed on all CFM56-3C1 and CFM56-3B2 engines, including over 1,800 engines that had already been delivered to customers.[4]

Applications

Specifications (CFM56-7B18)

Data from CFM International[52]

General characteristics

  • Type: Twin-spool, high-bypass turbofan
  • Length: 98.7 in (2.5 m)
  • Diameter: 61 in (1.55 m) (fan)
  • Dry weight: 5,216 lb (2,366 kg) (dry)

Components

  • Compressor: Single-stage fan, 3-stage low-pressure compressor, 9-stage high-pressure compressor
  • Combustors: annular
  • Turbine: Single-stage high-pressure turbine, 4-stage low-pressure turbine

Performance

See also

Related development

Comparable engines
Related lists

Notes

  1. ^ a b c Mixed Exhaust Flow is a term used to describe turbofan engines (both low and high bypass) that exhaust both the hot core flow and the cool bypass flow through a single exit nozzle. The core and bypass flows are "mixed".
  2. ^ a b Unmixed Exhaust Flow is a term used to describe turbofan engines (usually, but not exclusively high-bypass) that exhaust cool bypass air separately from their hot core flow. This arrangement is visually distinctive as the outer, wider, bypass section usually ends mid-way along the nacelle and the core protrudes to the rear. With two separate exhaust points, the flow is "unmixed".
  3. ^ Engine Trim is a term that generally refers to keeping the components of an engine in synchronisation with each other. For example, maintaining proper engine trim could mean adjusting the airflow to keep the proper amount of air flowing through the high-pressure compressor for a particular flight condition.
  4. ^ The Low-Pressure Shaft, in a two-shaft engine, is the shaft that is turned by the low-pressure turbine (LPT). Generally the fan section(s) and the booster section(s) (also known as the "low-pressure compressor") are located on the low-pressure shaft.
  5. ^ Shrouds are plates that are a part of a fan (or compressor, or turbine) blade. Generally, the shroud of one blade rests on the shroud of the adjacent blade, forming a continuous ring. Shrouds in the middle of blades are often used to damp vibrations. Shrouds at the tips of fan blades are often used to minimize air leakage around the tips. A midspan shroud is visible on the fan blades here. (Note that these fan blades are not from a CFM56.) (Gunston, Bill (2004). Cambridge Aerospace Dictionary. Cambridge University Press. 2004. p.558-9.)
  6. ^ Chevron is the name given to sawtooth cutouts that are sometimes applied to the exhaust nozzles of jet engines to reduce the jet noise. An example can be seen here. (Note that the pictured engine is not a CFM56.)
  7. ^ Dry Weight is the weight of an engine without any fluids in it, such as fuel, oil, hydraulic fluid, etc. Very similar to the dry weight of an automobile

References

  1. ^ a b c d e f g h i Bilien, J. and Matta, R. (1989). The CFM56 Venture. AIAA/AHS/ASEE Aircraft Design, Systems, and Operations Conference. Seattle, WA, 31 July – 2 Aug. 1989. AIAA-89-2038
  2. ^ "CFM delivers 20,000th engine". CFM International Website. Retrieved: 25 January 2010.
  3. ^ Fleet Statistics. CFM International website. Retrieved: 12 May 2010.
  4. ^ a b c d e f g h i j Norris, Guy (1999). CFM56: Engine of Change. Flight International. 19–25 May 1999. Online at CFM56: Engine of Change.
  5. ^ Samuelson, Robert (1972). "Commerce, Security and the "Ten Ton Engine"". The Washington Post. 8 October 1972, p. H7.
  6. ^ Farnsworth, Clyde (1973). "GE, French To Make Jet Engine". St. Petersburg Times, 23 June 1973, p. 11-A. Retrieved: 4 November 2009. Google News Archive.
  7. ^ GE-SNECMA Jet Engine Joint Venture (1972). National Security Decision Memorandum 189. 19 September 1972. NSDM 189 (pdf). Retrieved: 9 November 2009.
  8. ^ a b "A Rebuff to Pompidou on Engine" (1972). The New York Times. 30 September 1972, p. 39.
  9. ^ "Tooling up for Tiger". FLIGHT International. 7 January 1978, p. 8. Retrieved: 9 June 2010.
  10. ^ Farnsworth, Clyde (1973). "U.S. Ban Lifted on G. E. Plan". The New York Times. 23 June 1973, p. 37.
  11. ^ GE-SNECMA. CFM-56 Jet Engine Joint Development (1973). National Security Decision Memorandum 220. 4 June 1973. NSDM 220 (pdf). Retrieved: 9 November 2009.
  12. ^ CFM Timeline. CFM International Website. Retrieved: 10 November 2009.
  13. ^ "Work Split". CFM International website. Retrieved: 12 May 2010.
  14. ^ a b Yaffee, Michael (1975). "Developers Face 1975 CFM56 Decision". Aviation Week & Space Technology. 24 February 1975, p. 41.
  15. ^ Lewis, Flora (1975). "G.E.-SNECMA Deal: U.S.-French Dispute Is Obscured". The New York Times. 5 Mar 1975, p. 53.
  16. ^ "YC-15 Enters New Flight Test Series". Aviation Week & Space Technology. 21 February 1977, p. 27.
  17. ^ Shivaram, Malur (1988). A Survey of the Flight Testing, and Evaluation of CFM56 Series Turbofan. 4th AIAA Flight Test Conference, San Diego, CA. May 18–20, 1988. Technical Papers AIAA-1988-2078.
  18. ^ O'Lone, Richard (1978). Boeing to Offer 707-320 Re-engined with CFM56s. Aviation Week & Space Technology. 14 August 1978, p. 40.
  19. ^ "Plan to Reengine 707 With CFM56 Suspended". Aviation Week & Space Technology. 28 April 1980. p. 35.
  20. ^ a b Kazin, S (1983). KC-135/CFM56 Re-engine, The Best Solution. 19th AIAA/SAE/ASME Joint Propulsion Conference, 27–29 June 1983. Seattle, Washington. AIAA-1983-1374.
  21. ^ "GE, French Firm Get Jet Engines Contract". The Wall Street Journal. 8 November 1978, p. 14.
  22. ^ "CFM56 Selected for KC-135 Re-engining". Aviation Week & Space Technology. 28 January 1980, p. 18
  23. ^ "United Picks CFM56 for DC-8-60s". Aviation Week & Space Technology. 9 April 1979, p. 19.
  24. ^ a b c Epstein, N (1981). "CFM56-3 High By-Pass Technology for Single Aisle Twins". 1981 AIAA/SAE/ASCE/ATRIF/TRB International Air Transportation Conference, 26–28 May 1981, Atlantic City, New Jersey. AIAA-1981-0808.
  25. ^ Boeing 737 Deliveries. The Boeing Company. Retrieved: 19 May 2010.
  26. ^ "Preparing for the future of aircraft engines – TECH56". Aerospace Engineering and Manufacturing Online. Retrieved: 23 March 2010.
  27. ^ a b c d Morris, John (2000). ""Son of CFM56" – TECH56". Aviation Week's Show News Online. 24 July 2000. Retrieved: 23 March 2010.
  28. ^ a b c Angrand, A. (2007). "Tech Insertion: Eternal youth for the CFM56 (pdf)". SAFRAN magazine. November 2007. Retrieved: 23 March 2010. pp. 26–7.
  29. ^ "CFM Certifies Tech Insertion Compressor Upgrade; Brings Lower Fuel Burn, Longer On-Wing Life to Mature Fleet". CFM International Press Release. 14 July 2008. Retrieved: 23 March 2010.
  30. ^ "CFM Launches CFM56-7B Evolution Engine Program to Power Enhanced Boeing Next-Generation 737". GE Aviation Press Release. April 28, 2009. Retrieved: May 19, 2010.
  31. ^ a b c Norris, Guy (2010). Airbus Weighs Modified CFM56-5 Upgrade Options. Aviation Week. May 12, 2010. Retrieved: May 19, 2010.
  32. ^ Ostrower, Jon. "CFM56-7BE achieves FAA and EASA certification". Air Transport Intelligence news via Flightglobal.com. August 2, 2010. Retrieved: August 2, 2010.
  33. ^ a b "CFM56-5B Technology". CFM International website. Retrieved: 12 May 2010.
  34. ^ a b "CFM56-2 Technology". CFM International Website. Retrieved: 12 May 2010.
  35. ^ "CFM56-7: An In-Depth Look At The New Industry Leader". CFM International website, 12 June 1996. Retrieved: 13 May 2010.
  36. ^ a b Velupillai, David (1981). CFM56 Comes of Age. Flight International. 18 April 1981. Retrieved: 1 June 2010.
  37. ^ Norris, Guy (2004). "CFMI details insertion plan for Tech 56". Flight International. 3 August 2004. Retrieved: 17 November 2009.
  38. ^ "CFM'S Advanced Double Annular Combustor Technology". CFM International Press Release. 9 July 1998. Retrieved: 16 November 2009.
  39. ^ Mongia, Hukam (2003). TAPS –A 4th Generation Propulsion Combustor Technology for Low Emissions. AIAA/ICAS International Air and Space Symposium and Exposition: The Next 100 Years, 14–17 July 2003, Dayton, Ohio. AIAA 2003-2657.
  40. ^ "CFM56-5B/-7B Tech Insertion Package On Schedule For 2007 EIS". CFM International Press Release. 13 June 2005. Retrieved: 16 November 2009.
  41. ^ a b c "CFM56 rises to challenge". Flight International. 11 June 1991. Retrieved: 17 November 2009.
  42. ^ Brausch, John F. et al (2002). US Patent number: 6360528, "Chevron exhaust nozzle for a gas turbine engine". Retrieved: 22 March 2010.
  43. ^ Loheac, Pierre, Julliard, Jacques, Dravet, Alain (2004). CFM56 Jet Noise Reduction with the Chevron Nozzle. 10th AIAA/CEAS Aeroacoustics Conference. AIAA 2004-3044
  44. ^ Brady, Chris. Reverse Thrust. The 737 Technical Site. Updated: 23 May 2010. Retrieved: 28 May 2010.
  45. ^ NTSB No: DCA-06-MA-009. Section D.1.3 Thrust Reverser Description (pdf). National Transportation Safety Board. 10 April 2006. Retrieved: 28 May 2010.
  46. ^ Linke-Diesinger, Andreas (2008). "Chapter 8: Thrust Reverser Systems". Systems of Commercial Turbofan Engines: An Introduction to Systems Functions. Springer Berlin Heidelberg. doi:10.1007/978-3-540-73619-6_8. ISBN 978-3-540-73618-9. http://www.springerlink.com/content/u120828176525781/. 
  47. ^ "CFM56-3 Technology. CFM International website. Retrieved: 12 May 2010.
  48. ^ "CFM56-5A History". CFM International website. Retrieved: 12 May 2010.
  49. ^ "CFM56-5A Technology". CFM International website. Retrieved: 12 May 2010.
  50. ^ "CFM56-5B History". CFM International website. Retrieved: 20 November 2009.
  51. ^ "CFM56-5C Technology". CFM International website. Retrieved: 12 May 2012.
  52. ^ a b "CFM56-7B Technology". CFM International website. Retrieved: 12 May 2010.
  53. ^ "CFM56-7B History". CFM International website. Retrieved: 12 May 2010.
  54. ^ CFM56 Turbofan Engine Reliability. CFM International Website. Retrieved: 11 December 2009.
  55. ^ "Safety Recommendation A-05-19 and 20 (pdf)". [NTSB Recommendations]. National Transportation Safety Board, August 31, 2005. Retrieved: December 4, 2009.
  56. ^ "Report on the accident to Boeing 737-400, G-OBME, near Kegworth, Leicestershire on 8 January 1989" (1990). Report No: 4/1990. Air Investigations Branch. 25 August 1990. Retrieved: 22 March 2010.
  57. ^ "Derating Clears CFM56-3Cs to Fly" (1989). Flight International. July 1, 1989. Retrieved: December 11, 2009.

External links


Wikimedia Foundation. 2010.

Игры ⚽ Нужен реферат?

Look at other dictionaries:

  • CFM International CFM56 — Saltar a navegación, búsqueda CFM56 Archivo:Archivo:CFM56 P1220759.jpg Tipo Turbofán Fabricante CFM International Diseñado por …   Wikipedia Español

  • CFM International CFM56 — CFM56 Un CFM56 hors de sa nacelle. Constructeur …   Wikipédia en Français

  • CFM International CFM56 — CFM56 CFM International CFM56 ist die Bezeichnung einer Baureihe von Flugzeugtriebwerken. Die United States Air Force bezeichnet sie auch als F 108. Es handelt sich um Turbofan Triebwerke mit einem Nebenstromverhältnis von bis zu 6,5, die von CFM …   Deutsch Wikipedia

  • CFM International CFM56 — …   Википедия

  • CFM International LEAP-X — Maquette d un CFM International LEAP X Constructeur CFM International Premier vol 2016 Utilisation Comac C919 …   Wikipédia en Français

  • CFM International — Saltar a navegación, búsqueda Plantilla:Ficha de compañía CFM International es una empresa fruto de la colaboración entre GE Aviation de los Estados Unidos y Snecma de Francia. El proposito de esta compañía es construir y mantener los motores de… …   Wikipedia Español

  • CFM International — is a joint venture between GE Aviation of the United States, and Snecma of France. The sole purpose of the joint venture is to build and support the CFM56 series of jet engines.The names of CFM International and the CFM56 product line are derived …   Wikipedia

  • CFM International LEAP-X — Das CFM International LEAP X ist ein Mantelstrom Flugzeugtriebwerk des Herstellers CFM International, eines Joint Ventures von General Electric (USA) und Snecma (Frankreich). GE baut den Hochdruckteil des Triebwerks, Snecma den Niederdruckteil.… …   Deutsch Wikipedia

  • CFM International — Site web http://www.cfm56.com/ …   Wikipédia en Français

  • CFM International — Ein CFM56 Triebwerk CFM International ist ein Joint Venture mit Sitz in Paris, das 1974 zu gleichen Teilen von den beiden Triebwerksherstellern Snecma und General Electric gegründet wurde.[1] Gemeinsam wurde das Turbofan Triebwerk CFM56… …   Deutsch Wikipedia

Share the article and excerpts

Direct link
Do a right-click on the link above
and select “Copy Link”